® Dolphin 6100 Mobile Computer with Windows® CE 5.
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Table of Contents Chapter 1 - Agency Approvals Label Locations ....................................................................................................................1-1 Safety & RF Approvals by Country: .....................................................................................1-2 Dolphin RF Terminal—802.11b/g and/or Bluetooth .............................................................1-3 Chapter 2 - Getting Started Out of the Box ..................................................
Overview.............................................................................................................................. 5-1 Available Image Engines ..................................................................................................... 5-1 Depth of Field ................................................................................................................ 5-1 Supported Bar Code Symbologies ................................................................................
Limited Warranty Duration................................................................................................. 10-3 How to Extend Your Warranty .....................................................................................
vi
1 Agency Approvals Label Locations Dolphin 6100 mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Read these guidelines carefully before using your mobile computer. Compliance Label Laser Light Label Laser Light Label LASER LIGHT. DONOT STARE INTO BEAM CLASS 2 LASER PRODUCT 1.
Safety & RF Approvals by Country: Country Safety RF (Radio) U.S.A. UL60950-1 FCC Part 15, Sub part B Canada cUL60950 ICES-003, RSS 210 European Community IEC/EN 60950-1 EN 55022 (CISPR 22) Class B EN60825-1:1994 + A11 + A2 EN55024:1998 EN300 328 EN301 489-1 EN301 489-7 EN301 489-17 IEC 62209-2 China CCC SRRC Japan PSE AIRB, VCCI Australia EN60950 AS/NZS4268 Brazil ANATEL Mexico NOM COFETEL New Zealand EN60950 AS/NZS4268 R&TTE Compliance Statement—802.
Laser Safety Label If the following label is attached to your product, it indicates the product contains LASER LIGHT. DONOT STARE INTO BEAM CLASS 2 LASER PRODUCT a laser engine or laser aimer. 1.0 mW MAX OUTPUT : 650nM IEC 60825-1:1993+A1+A2 Complies with 21 CFR 1040.10 and 1040.1 1 Laser Eye Safety Statement: This device has been tested in accordance with except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. and complies with IEC60825-1: 1993+A1+A2 and 21 CFR 1040.10 and 1040.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To maintain compliance with FCC RF exposure guidelines for bodyworn operation, do not use accessories that contain metallic components. CAUTION! Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. ! Canadian Compliance This Class B digital apparatus complies with Canadian ICES-003.
2 Getting Started Out of the Box Verify that your carton contains the following items: • Dolphin 6100 mobile computer (the terminal) • Main battery pack (3.7v, Li-ion) • AC power supply • Localized plug adapters Note: Be sure to keep the original packaging in case you need to return the Dolphin terminal for service; see Product Service and Repair on page 10-1. Step 1. Install the Main Battery The 6100 is shipped with the battery packaged separate from the unit.
Step 2. Charge the Batteries 6100s ship with both the main battery pack and internal backup battery significantly discharged of power. Charge the main battery pack with the Dolphin charging cable for a minimum of 4 or 6 hours depending on your battery before initial use. 1. Attach the appropriate plug adapter to the plug of the power cable. 2. 3. Insert the plug into the appropriate power source. 1 2 Plug the Dolphin power cable into the DC Power Jack (see page 3-11) on the bottom end of the unit.
Desktop Note: You can access the Desktop any time by tapping the Change Views icon in the command bar and selecting Desktop on the popup menu. Tap to change views Command Bar Icons The command bar, located at the bottom of application screens, provides access to many system functions and programs. Left and right arrows are used to scroll through additional icons Icon Meaning Opens the Start menu. Tap to change views between open applications or to return to the desktop. Accesses the Bluetooth radio.
Icon Meaning Indicates the status of battery power. Double tap to open the Power control panel setting. When this icon shows a red power plug, it indicates the device is using external power. Displays the current time. Double tap to change the time and date. Indicates whether the keyboard is standard alpha (upper and lower case), all caps alpha, or in numeric mode. Press the alpha button on the keypad to switch modes. The up arrow allows you to turn the Wireless LAN and Bluetooth connection on or off.
Selecting Programs Tap Start > Programs. To open a program, tap the icon on the menu. Pop-Up Menus You can quickly choose an action for an item using the pop-up menus. 1. Tap and hold the stylus on the item name. The pop-up menu appears. 2. Lift the stylus and tap the action you want to perform. The contents of pop-up menus change according to the program you are using. Using Windows Explorer Use Windows Explorer to navigate through the files on your system.
2-6
3 Terminal Hardware Overview 6100 terminals include a number of standard terminal configurations as well as charging and communication peripherals and accessories to maximize the efficiency of your application setting. Standard Terminal Configurations There are two standard 6100 configurations: WPAN only and WPAN/WLAN. Both configurations include the following options; however, the WPAN/WLAN configuration has both a Bluetooth radio and an 802.11b/g radio.
Front Panel Features LED Touch Screen Display (screen protector installed at the factory) Scan key Keyboard (28-key numeric) Navigation keys Power key Software Reset key Scan/Decode LED The LED lights red when you press the Scan trigger in scanning applications. The LED lights green when a scanned bar code is successfully decoded. The LED is user-programmable. Keyboard A 28-key numeric keyboard is included on the unit. Microphone The integrated microphone can be used for audio recording.
Display Backlight The intensity of the backlight of the touch screen display may be changed and the backlight may be programmed to turn off after the terminal has been idle for a specified period of time. To adjust the intensity of the backlight while on battery power, tap Start > Settings > Control Panel > double tap Backlight. Screen Backlight - Battery/External Power Move the slider to adjust the screen backlight while on battery power.
Removing the Screen Protector 6100s ship with a touch screen protector already installed. To replace the screen protector, you must remove the one already installed. 1. Press the Power key to put the terminal in suspend mode. 2. Using a strong, flat, plastic card (e.g., credit card) wedge the edge of the card under the existing screen protector. Catch the edge of the screen protector and pull it up and away from the touch panel.
4. Align the exposed edge of the screen protector along the left edge of the touch panel. Make sure that it lies flush with edges of the touch panel. Backing Paper Screen Protector Note: To reposition the screen protector, lift up gently and reapply. 5. Use the card on top of the screen protector to smooth it out as you pull on the backing paper.
6. Pull smoothly and evenly from left to right until the screen protector is applied. Press gently but firmly. Use the card as necessary to smooth out any air pockets or bumps after application. 7. Press the Power key to wake the terminal and check the touch panel with the stylus. 8. Verify that the screen accepts input from the stylus as usual. If not, re-apply the screen protector. 9. Press the Power key to put the terminal back in suspend mode. 10.
12. For maximum performance, recalibrate the screen. Tap Start > Settings > Control Panel > double tap Stylus > Calibration tab. 13. Tap Recalibrate and follow the instructions on the screen.
Back Panel Features Image Engine Window Hand Strap (with Stylus) Speaker Finger Saddle Installed Battery Hand Strap The 6100 comes with an adjustable, elastic hand strap. The strap is attached to the device with the two small screws. It is threaded through the slot on the bottom of the back of the unit. Keep in mind that the hand strap covers the battery. When you want to replace the battery, you will need to adjust the hand strap accordingly.
Left Side Panel Features Micro SD Slot Side Button Side Button There is a button like this on both side panels. You can use the Programs Buttons option in the Control Panel to change the functionality of the scan buttons. Side Door The rubber door on the left side panel provides access to the Micro SD slot. When closed, the side door seals the terminal from moisture and particle intrusion thus preserving the terminal’s environmental rating.
Right Side Panel Features Side Button Headset Jack Headset Jack The rubber door on the right side panel provides access to the headset jack. This is a 2.5mm audio jack that supports a headset with a mono speaker and microphone. When closed, the side door seals the terminal from moisture and particle intrusion thus preserving the terminal’s environmental rating. Side Button There is a button like this on both side panels.
Bottom Panel Features DC Power Jack I/O Connector DC Power Jack The DC power jack receives external power from the Dolphin power cable that comes in the box with the terminal. When connected to the Dolphin power cable, the terminal is powered and the main battery pack is charging. I/O Connector The I/O mechanical connector is designed to work exclusively with Dolphin 6100 peripherals and cables. This connector powers the terminal, charges the main battery, and facilitates communication.
Dolphin HomeBase™ Device This charging and communication cradle supports USB and RS-232 communication, enabling your terminal to interface with the majority of enterprise systems. When a terminal is seated in a powered base, its main battery pack charges in four hours for the standard capacity 2200mAh pack and in six hours for the extended capacity 3300mAh pack. A spare battery may also be charged in the battery charging well behind the terminal.
Battery Power The intelligent battery technology inside the terminal features two types of battery power: • The main battery pack on the back panel (see Main Battery Pack on page 3-13) • The backup battery located inside the terminal (see Internal Backup Battery on page 3-15) Both batteries work together to prevent data loss when the terminal is used over long periods of time.
To fully charge the Li-ion battery before installing in the terminal, use the • Dolphin QuadCharger Device (see page 9-1) or insert the battery in the spare battery charging well in the back of either the Dolphin HomeBase or Dolphin eBase. Charging Time The standard capacity 2200mAh Li-ion battery pack requires four hours to charge to full capacity, while the extended capacity 3300mAh pack requires six hours.
• Never throw a used battery in the trash. It contains heavy metals and should be recycled according to local guidelines. • Don’t use a battery in any other manner outside its intended use in Dolphin terminals and peripherals. • Don’t short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury. • Excessive discharge damages a battery. Recharge the battery when your terminal indicates low battery power.
Resetting the Terminal Soft Reset: Using the stylus press and release the Reset button. This resets RAM and reloads the OS. Hard Reset: Using the stylus press and hold the Reset button and then press and release the Power button. This resets RAM, reloads the OS, and resets the Real Time Clock. Soft Reset (Warm Boot) A soft reset re-boots the terminal without losing RAM data and launches Autoinstall, which re-initializes the terminal.
1. Tap Start > Settings > Control Panel > System > Memory tab. 2. Move the slider to adjust the memory allocation and tap OK. The changes take effect immediately. Care and Cleaning of the Dolphin Terminal When needed, clean the image engine window and the LCD display with a clean, non-abrasive, lint-free cloth. The terminal can be cleaned with a damp cloth. Dolphin 6100 Technical Specifications Operating System Microsoft Windows CE 5.0 Development Environment Honeywell SDK for Windows® CE 5.
Expected Hours of Operation 8+ hours (with scan and continuously transmitting)* Charging 5V/3A input through bottom access or USB/Serial connector Expected Charge Time Standard Capacity: 2200mAh - four hours Extended Capacity: 3300mAh - six hours Charging Peripherals AC wall adapter and Charge/Communication Cable HomeBase–single-bay terminal charge/communicate eBase–single-bay terminal charge/communicate (via Ethernet connection) Quad Charger–four-slot battery pack charger WPAN (standard) Bluetooth
4 Using the Keyboard Overview The numeric keyboard is as follows: Navigation keys Power key Software Reset key Navigation Keys Located in the center of the keyboard for easy access with either hand, the navigation keys enable you to move the cursor up and down lines and from character to character.
Basic Keys Name Function ALPHA Toggles the keyboard between alpha (upper and lowercase) and numeric modes. Indicator changes accordingly on the command bar. Backspace Backspace moves the cursor back one space. If you are typing text, a character is deleted each time you press the backspace key. Control Modifies the next key pressed to type specific characters. Escape Cancels an action. Enter Performs the same function as the Enter key on a workstation. Power Suspends and resumes the terminal.
Note that when typing in alpha mode, you must use the same multi-press method you would use when typing letters on a phone keypad. Each key press types the next letter in the sequence as displayed by the alpha indicator. Function Key Combinations The Function key (FUNC) modifies the next key pressed to perform specific functions.
CTRL Key Combinations The Control key (CTRL) modifies the next key pressed to type specific characters. Key Combination Function CTRL + 1 ! CTRL + 2 @ CTRL + 3 # CTRL + 4 $ CTRL + 5 % CTRL + 6 ^ CTRL + 7 & CTRL + 8 ( CTRL + 9 ) CTRL + . - (minus) CTRL + 0 * CTRL + SP + (plus) The keyboard is color-coded in yellow to indicate these key combinations. Note: The color-coded indicators are located below each key.
5 Using the Image Engine Overview The 6100 houses a compact image engine using Adaptus™ Imaging Technology that instantly reads all popular 1D and 2D bar codes and supports omni-directional aiming and decoding. The image engine can also capture digital images, such as signatures and pictures of damaged inventory. Available Image Engines 6100s are equipped with 5300 Standard Range (5300SR) image engines. Depth of Field 5300 Standard Range (5300SR) 8.3 mil Linear Working Range*: (.020cm) 10 mil PDF417 (.
Supported Bar Code Symbologies Symbology Type Symbology Name 1D Symbologies Codabar Code 3 of 9 Code 11 Code 32 Pharmaceutical (PARAF) Code 93 Code 128 EAN with Add-On EAN with Extended Coupon Code EAN-13 GS1 Databar 2D Symbologies Aztec Code 16K Composite Data Matrix Grid Matrix GS1 Databar Han Xin MaxiCode OCR PDF417 QR Code Composite Codes Aztec Mesa Codablock F EAN·UCC GS1 Databar-14 OCR OCR-A OCR-B OCR-US Money Font Postal Codes Postnet and most international 4 state codes Australian Post Br
Activating the Engine When a scanning application is open, press the Scan key to activate the image engine. Using Demos Dolphin Demos are software utilities loaded on all Dolphin terminals that demonstrate the advanced features of the terminal. There are two Demos that feature the image engine: Image Demo and Scan Demo. To access these demos, tap Start > Programs > Demos. • Select Scan Demo to verify decoding, or • Select Image Demo to verify imaging.
Sample Bar Codes You can use the following bar codes to verify decoding: Sample 128 Sample PDF417 Code 128 PDF417 Test Message Omni-Directional Scanning Positions The high-vis aiming pattern frames the bar code to provide you with the best scanning performance. Note: To achieve the best read, the aiming beam should be centered horizontally across the bar code. The aiming pattern is smaller when the terminal is held closer to the code and larger when the terminal is held farther from the code.
Capturing Images The image-capture process is an intuitive, split-second operation for experienced users. By following basic guidelines, however, new users can easily develop their own technique and, with practice, quickly learn to adapt to different application environments. Image Preview When the imaging process is initiated, the touch screen displays a preview of the object.
5-6
6 Communication Communication Options Dolphin terminals offer several communication options including Microsoft ActiveSync and wireless radios. I/O Connector (Wired Communication) The mechanical connector on the bottom panel (see DC Power Jack on page 3-11) connects the terminal to various Dolphin communication peripherals that connect to a host workstation via USB (1.1 or higher), thus enabling ActiveSync communication. For more information, see ActiveSync Communication on page 6-2.
Connecting the USB Cable Connect the USB cable to the I/O connector to facilitate USB communication between the Dolphin terminal and the host workstation. DC Power Jack Host Workstation I/O Connector USB Cable USB Connector ActiveSync Communication To synchronize, ActiveSync 4.1 or higher must be installed and configured for the appropriate communication type on the host workstation and the Dolphin terminal. Dolphin terminals ship with ActiveSync already installed.
Hardware Requirements for Setup • • • • • Dolphin communication peripheral Dolphin power cable USB Cable (for USB communication) ActiveSync v4.1 or higher installed on the host workstation Windows 98 Second Edition, Windows Me, Windows 2000, Windows NT (4.0 SP6 or higher) or Windows XP computer. Software Requirements for Communication To sync successfully, ActiveSync must be configured for same communication type on both the host workstation and the Dolphin terminal.
Tap Change Connection to change the current settings. Connection Options Select this option to … Bluetooth Establish an ActiveSync connection via Bluetooth; see Connecting to Other Devices on page 7-1. This menu item is present only when Bluetooth has been activated. ‘USB Establish a USB connection. Communicating with the Dolphin Terminal After setting up both the workstation and the terminal, ActiveSync connection should be automatic. 1.
The Mobile Device folder opens in Windows Explorer. The Dolphin terminal is now treated as a mass storage device, and transferring files is as simple as dragging and dropping or copying and pasting as you would for moving files between folders on your hard drive. Adding Programs via ActiveSync ! When selecting programs, verify that the program and version of the program are designed for the Windows CE 5.0 and the terminal’s processor.
If the File is Not an Installer Some programs cannot be installed on workstations because they are designed exclusively for Windows CE devices. In these cases, the appropriate files must be stored on the host workstation and transferred to the terminal via ActiveSync Explore. Note: You know that the program is not an installer because an error message stating that the program is valid but designed for a different type of computer appears when you try to install the program on the workstation. 1.
For complete configuration instructions, download the Honeywell Secure Wireless (SWC) Client User’s Guide from www.honeywellaidc.com. A link to this guide appears on the Dolphin 6100 product page. Adding Programs from the Internet When you have established a network connection (whether via modem or wireless radio), you can access the Internet and download additional software programs. When selecting programs, verify that the program and version of the program are designed for Windows CE 5.
6-8
7 Bluetooth Manager Bluetooth wireless technology is a short-range communications technology to connect portable and/or fixed devices while maintaining high levels of security. Enabling the Bluetooth Radio 1. Select the device panel indicated by the UP arrow in the lower, right portion of the display. 2. Tap Turn Bluetooth On. The Bluetooth icon appears in the task bar.
2. Activate your mobile phone’s Bluetooth feature. 3. Select Start - Settings - Network and Dial-up Connections. 4. Double tap on Make New Connections. 5. Choose Dial-up Connection and select Next. 6. Select Bluetooth. 7. Select and activate the data modem service for your phone (refer to Pairing Bluetooth Devices (page 7-1) and press OK. 8. Select the data modem service from step 7 from the Select a Modem: drop down menu. 9. Enter a dial-up phone number.
8 Dolphin HomeBase/eBase Device Overview Note: The information in this chapter applies to both the Dolphin HomeBase and Dolphin eBase devices unless otherwise indicated. As the hub of your Dolphin 6100 system, the Dolphin HomeBase charging and communication cradle supports full-speed USB 1.1 and RS-232 communication with a workstation. The Dolphin eBase is identical to the Dolphin HomeBase except it supports Ethernet communication as well as USB 1.1, RS232.
Convenient Storage The battery charging system makes the base a safe and convenient storage receptacle for your terminal. Capacity The base holds one 6100 and charges its battery pack. It also charges a spare battery in the well behind the terminal. Power Supply The power cable that ships with each terminal also powers the base. ! We recommend use of Honeywell peripherals, power cables, and power adapters.
Back Panel HomeBase eBase Serial Port Serial Port USB Port USB Port DC Power Jack Ethernet Port DC Power Jack DC Power Jack Connect the power cable to this power jack; see Powering the Dolphin HomeBase Device on page 8-4. USB Port The USB port is full-speed (v1.1). Using the USB cable, you can connect the base to a USBcompliant device to facilitate USB communication to and from the terminal. USB communication occurs through Microsoft ActiveSync (v.4.1 or higher).
Powering the Dolphin HomeBase Device The terminal requires 5 volts DC input for communication and battery charging; the power adapter on the power cable converts the voltage from the power source to 5 volts DC. Only power adapter cables from Honeywell convert the voltage appropriately. The same power cable that ships with each terminal can be used to power the base. This cable contains a plug adapter for each geography (US, UK, EU, etc.). Plug Adapter Power Adapter Power Cable 1.
Charging the Main Battery The base powers the terminal and fully charges its main battery pack in 4 or 6 hours depending on the battery. As battery packs charge, the charging circuitry follows the twostep charging process (CC-CV) that is recommended for Li-Ion batteries. The process monitors changes in temperature, current, and voltage. Inserting a Terminal 1. Install the battery pack in the terminal; see Install the Main Battery on page 2-1. 2.
Charging a Spare Battery The base can also charge a second battery while the terminal is positioned in the base. The second battery can be inserted in the battery charging well in back of the terminal connection. Place the battery in the well with the label facing up and toward the back of the unit. Angle the battery as shown. Once the connectors engage, the LED lights. If the LED is red, the unit is charging; if it is green, the charge is complete.
Technical Specifications Structural Dimensions 5.3 in. high X 4.5 in. wide X 3.1 in. deep (13.5 cm. X 11.4 cm. X 7.9 cm.) Weight Dolphin HomeBase - 11.0 oz. (313g) Dolphin eBase - 11.
8-8
9 Dolphin QuadCharger Device Overview The Dolphin QuadCharger device is a four-slot charging station that charges up to four Li-ion battery packs—both standard capacity 2200mAh and extended capacity 3300mAh—in four hours and six hours respectively. For more details about charging, see Battery Charging on page 9-2. ! We recommend use of Honeywell peripherals, power cables, and power adapters. Use of any non-Honeywell peripherals, cables, or power adapters may cause damage not covered by the warranty.
Battery Charging Charging Process This charger charges 6100 standard capacity Li-ion 2200mAh battery packs in four hours and extended capacity 3300mAh packs in six hours. Each charging slot works independently of the other three. As battery packs charge, the charging circuitry follows the two-step charging process (CC-CV) that is recommended for Li-Ion batteries. The process monitors changes in temperature, current, and voltage.
Recommendations for Storing Batteries To maintain top performance from batteries, follow these storage guidelines: • Avoid storing batteries outside of the specified temperature range of -4 to 122° F (-20 to 50°C) or in extremely high humidity. • For prolonged storage, do not keep batteries stored in a charger that is connected to a power source. Troubleshooting If you encounter problems with the charger, refer to chart below for possible solutions.
Technical Specifications Structural Dimensions 7.3 in. long X 3.7 in. wide X 2.4 in. high (18.5 cm. X 9.4 cm. X 6.1 cm.) Weight 11.5 oz.
10 Customer Support Product Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product. North America Telephone: (800) 782-4263 Fax: (803) 835-8012 E-mail: naservice@honeywell.
Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 E-mail: latechsupport@honeywell.com Brazil Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105 E-mail: brsuporte@honeywell.com Mexico Telephone: (803) 835-8000 E-mail: latechsupport@honeywell.com Europe, Middle East, and Africa Telephone: +31 (0) 40 7999 393 Fax: +31 (0) 40 2425 672 E-mail: eurosupport@honeywell.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS.
10 - 4
Honeywell 700 Visions Drive P.O.
