Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series m WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series TABLE OF CONTENTS 1 PRODUCT DESCRIPTION . . . . . . . . . . . . . 1 1.1 1.2 1.3 1.4 1.5 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Principle of Operation . . . . . . . . . . . . . . . . . . Product Nomenclature . . . . . . . . . . . . . . . . . . Abbreviations & Definitions . . . . . . . . . . . . . . Symbols & Definitions . . . . . . . . . . . . . . . . . .
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 8 ANTENNA SELECTION, ADJUSTMENT & MOUNTING . . . . . . . . . 26 8.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Antenna Designs & Considerations . . . . . . . 8.2.1 Omni-directional Antenna Design . . . . . 8.3 Antenna Mounting & Considerations . . . . . . 8.3.1 Mounting to RF Signal . . . . . . . . . . . . . . 8.4 Antenna Options . . . . . . . . . . . . . . . . . . . . . 8.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 List of Figures Figure 1. Figure 2. Figure 3a. Figure 3b. Figure 3c. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 Intended Audience 1 | PRODUCT DESCRIPTION This guide is intended for people who are responsible for planning, configuring, administering, and operating the Limitless™ Network. 1.1 | General Prerequisite Skills It is assumed that you are familiar with the operation of Limitless™ Networks.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 1.3 | Product Nomenclature This document is valid for the Limitless™ Receiver, WMPR Series in the following variations. Figure 1. Limitless™ Receiver, WMPR Series Nomenclature WMPR 1 A 00 A 1 A 1 Receiver type GEN code RF code Antenna type code Country use code Output code Seal code Mounting code WMPR Series Multi-Protocol Receiver 2 1 Version 1 sensing.honeywell.com A 2.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 1.4 | Abbreviations and Definitions Table 1.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 1.5 | Symbol Definitions The following table lists those symbols used in this document to denote certain conditions. Table 2. Symbol Definitions Symbol Definition , ATTENTION: Identifies information that requires special consideration. TIP: Identifies advice or hints for the user, often in terms of performing a task.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 2 | SPECIFICATIONS, CERTIFICATIONS, AND APPROVALS 2.1 | Intended Country Usage Table 3. North America; Country Code Use “A” Country ISO 3166 2 letter code UNITED STATES US CANADA CA Table 4. Asia Pacific; Country Code Use “B” Country ISO 3166 2 letter code AUSTRALIA AU Table 5.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 2.2 | Certifications and Approvals 2.4 | Electrical Specifications See product labels for applicable approvals and ratings. Table 9. Electrical Specifications Table 7. Communication Approvals and Standards Item Specification Approval/Item Ratings/Description Supply voltage 10 Vdc to 30 Vdc Enclosure type IP20 Supply current 500 mA max.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 2.5.2 | Update Rate vs. RF Lost Indication 2.9 | Antenna Connection Table 12 displays the approximate amount of time it takes for the WMPR to indicate a Node Lost RF with respect to the Update Rate that the Node is set to. Antennas connect to an RP-SMA male connector on the upper surface of the WMPR.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 2.10.2 | Industry Canada (IC) Compliance Statements • To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the equivalent isotropic radiated power (EIRP) is not more than that permitted for successful communication.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 2.10.5 | European Declaration of Conformity Statements This section contains the European Declaration of Conformity (DoC) statement for the radio used in the Limitless™ WMPR receiver. European Declaration of Conformity (DoC) 2.10.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 3 | WMPR FEATURES 3.1 | LED Indicator Figure 2. Limitless™ WMPR Multi-Protocol Receiver with location call-out The WMPR LED operates as follows (see Figure 2 7): 10 sensing.honeywell.com Table 14.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 3.2 | Limitless™ Switch and Sensor Function Buttons ISSUE 1 32309669 Figure 3c. Limitless™ WPS: Reset Button and LED Figure 3a. Limitless™ WBX: Function Button and LED Figure 3b.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 4 | R.F. INTERFERENCE CONSIDERATIONS 4.1 | R.F. Interference Considerations 4.1.1 | General The 802.15.4 specification provides a high resistance to interference. Within the 2.4 GHz band, there are 16 channels, each using approximately 2 MHz of bandwidth. The channel used may be rapidly changed depending on the presence of other signals sensed in that channel.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 5 | SETUP AND ELECTRICAL CONNECTIONS m WARNING RISK OF ELECTRICAL SHOCK Potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4 V peak, or 60 Vdc may be accessible. ISSUE 1 32309669 5.2 | EtherNet/IP™ Output Connection 5.2.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 6 | LCD/MENU/MODE OPERATION ISSUE 1 32309669 Figure 6. Main Menu 6.1 | Start-up or Re-start Sequence Mode (EtherNet/IP™ Active Connection and Power Supplied to WMPR) 6.1.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 EtherNet/MAC ID screen appears (see Figure 9). (Record the MAC ID, IP Address, and then touch the “Next” function button to move to the Main Menu) (see Figure 10). 6.2 | Main Menu Figure 9. EtherNet/IP™ MAC ID & IP Address The Main Menu (see Figure 11) allows you to see the status “at-a-glance” of the EtherNet/IP™ connection and information of ALL the Nodes currently paired to the WMPR.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 6.2.3 | Node Information Node Information: The Main Menu will display RF Lost and Low Battery (see Figure13) for a single node or multiple nodes based the conditions occurring. Table 15.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series Configuration Menu: Allows you to take action to Pair or Purge Nodes, Change Update Rate or Node LCD Display Time, or Reset to WMPR to Factory Defaults. Functionality described in Section 8.6 Receiver Detail: Receiver information specific the WMPR device which includes WMPR FirmWare revision, Part Number, Radio FirmWare revision, Radio MAC ID, and Radio Transmit Power. Functionality described in Section 8.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 6.5.3 | Node Detail Menu, Screen 3 Figure 19. Node Detail, Screen 3 ISSUE 1 32309669 MORE: Moves to next screen where there are more modes to choose (see Figure 21). Figure 21. Configuration Menu, continued A description of the Node Detail “screen 3” information (see Figure 19) is as follows: Table 18.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 6.7 | Receiver Detail Figure 22. Receiver Detail Menu 32309669 Table 20. Receiver Information, Screen 2 Display Indication WMPR REV Firmware version of WMPR main processor IP Address Internet Protocol address Enternet IP/ MAC ID EtherNet/IP™ Media Access Control address Figure 24.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series Table 23. Pair Mode Step Action 1 Completely read this procedure before starting in order to understand the timing of events that need to be performed. 2 Limitless™ switch: Remove (if required) the screws on then housing cover and then the cover of the Limitless™ switch and locate the function button 8 (see Figure 3a or b) to be used in Step 4.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series The PURGE MODE (see Figure 29) can be accessed by touching the “PURGE” function button as displayed in the Configuration Menu (see Figure 21). Once you are in the PURGE MODE you can choose ALL or any of the 14 node numbers to purge by scrolling “Up” or “Down” to the desired Node number and then touching “Start”. ISSUE 1 32309669 6.10 | Node Update Rate Mode Figure 33.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series Figure 35. Node Update Rate - Update Rate Displayed ISSUE 1 32309669 The NODE LCD DISPLAY TIME Mode (see Figure 37) can be accessed by touching the “NODE LCD DISPLAY” function button as displayed in the Configuration Menu (see Figure 21). Once you are in the NODE LCD TIME Mode you can choose any of the 14 node numbers to update by scrolling “Up” or “Down” to the desired Node number and then touching “Enter”.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series Figure 40. Node LCD Time - Updated LCD Time Displayed (i.e., 5s, Off 5s) Note: If the particular Node # that you are trying to update does not have an LCD display, the screen will display “Node LCD N/A”. ISSUE 1 32309669 Figure 42. Reset of Receiver In-Process Figure 43. Network Start Notice 6.12 | Factory Reset Receiver Mode Figure 41.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 7 | ANTENNA, CABLE, & MOUNTING OPTIONS 7.1 | Approved Antenna Options This section defines the antenna options that can be used in a particular country of interest; reference Section 2.1 for a list of Countries per Country Use Code. It is important to determine the country the WMPR will be used in.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 Table 23.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 8 | ANTENNA SELECTION, ADJUSTMENT, AND MOUNTING 8.1 | Warnings 8.1.1 General Installation Warnings , ATTENTION • Professional Installation is required to ensure conformity with Federal Communications Commission (FCC) in the USA, Industry Canada (IC) in Canada and the Radio and Telecommunications Terminal Equipment Directive, 1999/5/ EC (R&TTE), in the European Union (EU).
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series If a person comes in contact with electrical power, and cannot move DO NOT TOUCH THAT PERSON OR RISK ELECTROCUTION. • 32309669 8.2 | Antenna Designs and Considerations m WARNING • ISSUE 1 Use a non-conductive dry board, stick, or rope to push, pull, or drag them so they no longer are in contact with electrical power.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 8.3 | Antenna Mounting and Considerations 8.3.1 Antenna Mounting Location with Respect to RF Signal m WARNING RF EXPOSURE To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm [7.87 in] or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operation at closer than this distance is not recommended.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 8.4 | Antenna Options The following chart lists the antenna options along with the various characteristics that will be referenced throughout this section. This section is intended to assist an end user in determining which antenna(s) are worth investigating and subjecting to application requirements for proof of suitability. Table 26. Antenna Options Ant.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 , ATTENTION , CAUTION The antenna cables should not be modified (i.e. cut short and/ or re-terminated) as it may affect Communication Agency approval. Power to the WMPR should not be applied during installation of an antenna as damage could occur to the WMPR electronics.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 8.5.2 | Cable Requirement Some remote mount antennas have an antenna cable permanently attached, with an RP-SMA plug, that is simply connected to the jack on the WMPR. Other remote mount antennas do not include cable, and require the use of an extension cable.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series Mast mount: The benefit of the mast-mount antenna is its rigid design and resistance to displacement when subjected to shock, vibration, wind, etc. It can be easily mounted high above the ground to obtain greater RF signal performance and it withstands winds up to 100 mph. Catalog listing: WAN06RNJ Mast-mount bracket (Included with the 8 dBi antenna): Attach antenna to its mounting bracket. Tighten nut.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 Figure 56. Highest RF signal when antennas are as parallel to each other as possible (parallel arrangement shown with the Limitless™ WMPR monitor and WPS sensor) 8.5.5 | Grounding the Remote Antenna Follow these guidelines to ground the antenna in accordance with national electrical code instructions. Table 25. Grounding the Antenna Step Action 1 Use No. 10 AWG copper or No.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 8.6 | Antenna Environmental Usage/Concerns 4 8.6.1 | Choosing an Antenna/Cable to Meet Application Exposure Conditions There is no antenna or cable design impervious to every environmental condition it could be exposed to. Review the application environment as follows: Step Action 1 Determine where the antenna will be installed and the application conditions: indoor, outdoor, or limited outdoor exposure.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 8.6.3 | Outdoor Antenna Installations - Lightning Concerns Outdoor antenna installations can lead to the possible damage caused by nearby lightning strikes that induce charges or surges on the antenna and/or antenna extension cables. A lightning arrestor such as the AL6-RSPRSJBW-9 from L-COM Global Connectivity can be reviewed against application requirements.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 8.7 | Choosing an Antenna Gain (dBi) with Acceptable Fade-Margin There are several different Limitless™ Series antenna gain options to choose from. This section helps determine the antenna version(s) that will provide suitable RF signal performance for specific applications.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series 9 | WMPR MOUNTING ISSUE 1 32309669 Figure 59. Limitless™ WMPR Mounting Plate The WMPR is intended to be mounted to a Din-Rail or mounted via the mounting plate. 9.1 | Din-Rail Mounting The WMPR DIN-Rail bracket is supplied with the WMPR and can be “snapped” on to a 35mm DIN-RAIL. Figure 58. Limitless™ WMPR DIN-RAIL bracket 10 | INSPECTION AND MAINTENANCE 10.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 11 | CHOOSING A WMPR SERIES CATALOG LISTING This section is intended to be used for identifying a catalog listing from the WMPR nomenclature to determine suitability in a particular application. Figure 60.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 13 | ACCESSORIES Table 27. Limitless™ Antennas Part Number Antenna Type Code (if ordered with a wireless switch) Antenna Design Antenna Gain (dBi) Connector/ Mounting Dimensions WAN01RSP 01 straight 2.2 RP-SMA plug/direct mount Ø 9,91 mm x 112,78 mm L [Ø 0.39 in x 4.44 in L] WAN02RSP 02 tilt/swivel 2.2 RP-SMA plug/direct mount Ø 9,91 mm x 112,78 mm L [Ø 0.39 in x 4.
Installation and Technical Manual for the ISSUE 1 Limitless™ Multi-Protocol Receiver, WMPR Series 32309669 Table 28.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series ISSUE 1 32309669 14 | INSTALLATION DRAWING Figure 61. WMPR DImensions 41,4 mm [1.63 in] RP-SMA antenna connector jack Din bracket (mounting code 2) 80,0 mm [3.15 in] EtherNet/IP™ RJ-45 connector +- Power supply lever-actuated connector 7,87 mm [0.31 in] 159,51 mm [6.28 in] 152,4 mm [6.0 in] 2,36 mm [0.093 in] thickness 88,9 mm [3.5 in] 4X Ø 4,57 mm [4X Ø 0.
Installation and Technical Manual for the Limitless™ Multi-Protocol Receiver, WMPR Series WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details.