69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 1 Friday, April 29, 2011 12:04 PM System Installation Guide TL9160 Wireless Thermostat Kit With Equipment Interface Module Français : voir la page 25 • Espagnol : vea la página 49 Installation guide for: • Wireless equipment interface module • TL9160 wireless thermostat • Wireless remote control • Wireless outdoor air sensor IMPORTANT INSTRUCTIONS ELECTRICAL HAZARD Can cause electrical shock or equipment damage.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 2 Friday, April 29, 2011 12:04 PM Installation Guide System installation at a glance 1.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 3 Friday, April 29, 2011 12:04 PM TL9160 Install the Equipment Interface Module (EIM) 2. Determine the location The equipment interface module (EIM) consists of a relay and an antenna. They can be installed either in the wiring compartment of the baseboard heater or in a 4”x4” junction box. NOTE: Install EIMs at a minimum distance of 2 feet (0.6 m) of each other.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 4 Friday, April 29, 2011 12:04 PM Installation Guide Installation in the heater ELECTRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect AC power before beginning installation. Wiring must comply with local electrical codes. Use special CO/ALR solderless connectors if supply wires are made of aluminum. NOTE: First, disconnect the heater wires from the supply wires. If the heater has a built-in thermostat, remove it.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 5 Friday, April 29, 2011 12:04 PM TL9160 Installation in a 4”x4” junction box ELECTRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect AC power before beginning installation. Wiring must comply with local electrical codes. Use special CO/ALR solderless connectors if the supply wires are made of aluminum. 1) Mount the junction box on the wall.
9-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 6 Friday, April 29, 2011 12:04 PM Installation Guide Install batteries in wireless devices Thermostat Install 2 AA alkaline batteries Remote control Install 3 AA alkaline batteries 3. Outdoor air sensor Install 2 AA lithium batteries Link all devices to wireless network 4. Start wireless setup Press the CONNECT button on the antenna to place it in wireless setup.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 7 Friday, April 29, 2011 12:04 PM TL9160 Link thermostat and EIM to wireless network Perform the following steps on the thermostat: NOTE: You can skip step 2 if you do not have a wireless remote control or do not have more than one wireless thermostat in your house. # Display Button Step 1) The Link menu appears when you connect the thermostat to wireless network for the first time. Press OK to select Zone.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 8 Friday, April 29, 2011 12:04 PM Installation Guide Link additional EIM to wireless network (if applicable) NOTE: Perform steps 1 to 6 for each additional EIM. You can link a maximum of 8 EIMs to the wireless neywork. 1) If the green light on the EIM that was last linked is still flashing, press its CONNECT button. The green light will become steady.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 9 Friday, April 29, 2011 12:04 PM TL9160 Link outdoor sensor to wireless network (if applicable) 1) Make sure the green light on the EIM is flashing; this indicates the wireless setup is still active. If not, activate the wireless setup (see page 6). Press and NOTE: If you have more than one wireless release thermostat, make sure to activate the wireless setup from an EIM connected to the same network as the thermostat.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 10 Friday, April 29, 2011 12:04 PM Installation Guide 1) 2) Exit wireless setup 5. Press the CONNECT button at the EIM. The green flashing light on the antenna will change to a steady green light. NOTE: If you do not press the CONNECT button, the EIM will automatically exit wireless setup after 15 minutes of inactivity. Put the cover back on the antenna module. Customize the thermostat 6.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 11 Friday, April 29, 2011 12:04 PM TL9160 Default settings Parameter Temperature unit Time format Choices Default setting To modify, see °C / °F °F Page 11 12h Page 11 Minimum setpoint 41°F (5°C) Page 12 Maximum setpoint 86°F (30°C) Page 12 On / Off On Page 13 Lock None / Partial / All None Pages 13-14 Zone 1, ...
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 12 Friday, April 29, 2011 12:04 PM Installation Guide Minimum and maximum setpoints Follow this procedure to set the minimum and maximum setpoint temperature. # Display Button Step 1) From the installer’s setup menu, press to select Setpoints and press OK. 2) Press OK to select Min. 3) If necessary, press or to change the minimum setpoint. Press OK. 4) Press OK to select Max.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 13 Friday, April 29, 2011 12:04 PM TL9160 Anti-freeze When this function is on, the EIM will maintain the room temperature at 55°F (13°C) if it loses communication with the thermostat or if the thermostat sensor is defective. The protection automatically turns on when the EIM is linked to the thermostat. Leave the protection on unless the EIM is installed in a junction box in a separate room from the heater.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 14 Friday, April 29, 2011 12:04 PM Installation Guide # Display Button Step 1) From the installer’s setup menu, press to select Lock and press OK. 2) Press or to select All, Part (partial) or None. Press OK. 3) Press Exit once to return to installer’s setup menu or twice to return to home screen. Zone The zone name is used to identify the thermostat on the wireless remote control.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 15 Friday, April 29, 2011 12:04 PM TL9160 3) Press or to set the value. Press OK. 4) Press Exit once to return to installer’s setup menu or twice to return to home screen.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 16 Friday, April 29, 2011 12:04 PM Installation Guide Adaptive Intelligent Recovery Available only if you use the thermostat in programmable mode. When Adaptive Intelligent Recovery is on, the thermostat “learns” how long your heater takes to reach the set temperature. The thermostat will then determine when to activate heating so the desired temperature is attained at the desired time.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 17 Friday, April 29, 2011 12:04 PM TL9160 Copy Use this function to copy the configuration settings, the schedule settings or both to the other wireless thermostats if you have several wireless thermostats in your house. This function is available only if the thermostat is connected either to a remote control or to an outdoor sensor.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 18 Friday, April 29, 2011 12:04 PM Installation Guide Mount thermostat and outdoor sensor 7. Follow the guidelines below when mounting the thermostat: • Do NOT install the thermostat in an area where it can be exposed to water or rain. • Avoid locations where there are air drafts (top of staircase, air outlet), dead air spots (behind a door), direct sunlight or concealed chimney or stove pipes.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 19 Friday, April 29, 2011 12:04 PM TL9160 3) Install the outdoor sensor (optional) Press and release Hold sensor where you intend to install it and press the CONNECT button. If sensor is communicating with the thermostat, the latter will display the outdoor temperature. Mount the sensor vertically on an exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 20 Friday, April 29, 2011 12:04 PM Installation Guide Verifying the signal strength between the EIM and the thermostat 9. NOTE: If you have several EIMs linked to the thermostat, the displayed value is between the thermostat and the first linked EIM. The signal strength ranges from 0 (no signal) to 10 (strongest). # Display Button Step 1) From the home screen, press and hold the right center button for 5 secs.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 21 Friday, April 29, 2011 12:04 PM TL9160 NOTE 1: If you have more than one EIM in the wireless network, you can link the wireless device from any of the EIMs. NOTE 2: If you have more than one wireless thermostat, link the remote control or the outdoor sensor to the wireless network of each wireless thermostat.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 22 Friday, April 29, 2011 12:04 PM Installation Guide Specifications & replacement parts Thermostat Temperature setpoint range: Temperature setpoint resolution: Temperature display range: Temperature display resolution: Heating cycle rate: Programming: 41°F - 86°F (5°C - 30°C) 1°F (0.5°C) 32°F - 104°F (0°C - 40°C) 1°F/ 0.
69-2474EFS (Honeywell YTL9160 System Installation Guide).book Page 23 Friday, April 29, 2011 12:04 PM TL9160 Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.
69-2474EFS (Honeywell YTL9160 System Installation Guide).