OneWireless OWA 100 OneWireless Adapter User Manual 34-XY-25-40 Revision 1 September 2010
Notices and Trademarks Copyright 2010 by Honeywell International Inc. Revision 1 September 2010 While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may be stated in its written agreement with and for its customers. In no event is Honeywell liable to anyone for any indirect, special or consequential damages.
About This Document This document describes mounting, installation, wiring, operation and maintenance of the OWA 100 Wireless Adapter are covered in other documents. Honeywell does not recommend using devices for critical control where there is a single point of failure or where single points of failure result in unsafe conditions. OneWireless is targeted at open loop control, supervisory control, and controls that do not have environmental or safety consequences.
Europe Contact: Phone: Facsimile: Mail: Honeywell TAC-EMEA +32-2-728-2732 +32-2-728-2696 TAC-BE02 Hermes Plaza Hermeslaan, 1H B-1831 Diegem, Belgium Contact: Phone: Honeywell Global TAC – Pacific 1300-300-4822 (toll free within Australia) +61-8-9362-9559 (outside Australia) +61-8-9362-9564 Honeywell Limited Australia 5 Kitchener Way Burswood 6100, Western Australia GTAC@honeywell.
Singapore Contact: Phone: Facsimile: Mail: Email: Honeywell Global TAC – South East Asia +65-6580-3500 +65-6580-3501 +65-6445-3033 Honeywell Private Limited Honeywell Building 17, Changi Business Park Central 1 Singapore 486073 GTAC-SEA@honeywell.com Taiwan Contact: Phone: Facsimile: Mail: Email: Honeywell Global TAC – Taiwan +886- 7- 536-2567 +886-7-536-2039 Honeywell Taiwan Ltd. 17F-1, No. 260, Jhongshan 2nd Road. Cianjhen District Kaohsiung, Taiwan, ROC Global-TAC-Taiwan@honeywell.
Symbol Definitions The following table lists those symbols used in this document to denote certain conditions. Symbol Definition ATTENTION: Identifies information that requires special consideration. TIP: Identifies advice or hints for the user, often in terms of performing a task. CAUTION Indicates a situation which, if not avoided, may result in equipment or work (data) on the system being damaged or lost, or may result in the inability to properly operate the process.
Symbol Description The C-Tick mark is a certification trade mark registered to ACMA (Australian Communications and Media Authority) in Australia under the Trade Marks Act 1995 and to RSM in New Zealand under section 47 of the NZ Trade Marks Act. The mark is only to be used in accordance with conditions laid down by ACMA and RSM. This mark is equal to the CE Mark used in the European Union. N314 directly under the logo is Honeywell’s unique supplier identification number.
Contents Support and contact info .......................................................................................................................iii 1. INTRODUCTION .................................................................................................... 1 1.1 SAFETY MESSAGES.....................................................................................................................1 Warnings......................................................................................
Contents 4. OPERATION ........................................................................................................ 19 4.1 Overview ......................................................................................................................................19 OWA 100 Adapter display modes ........................................................................................................................19 4.2 OWA 100 Adapter connection status ...................................
Contents Tables Tables Table 1 OWA 100 Adapter connection status .............................................................................................19 Table 2 Buttons for Device Local Configuration ..........................................................................................24 Table 3 Read Node Information ..................................................................................................................25 Table 4 Advanced Options ......................................
1. Introduction 1.1. Safety Messages 1. Introduction 1.1 Safety Messages These instruction procedures may require special precautions to ensure the safety of the personnel performing the operations. Information that potentially raises safety issues is indicated by a warning symbol ( ). Please refer to the following safety messages before performing an operation preceded by this symbol. WARNING Warnings Failure to follow these instructions could result in death or serious injury.
1. Introduction 1.5. About the OWA 100 OneWireless Adapter 1.5 About the OWA 100 OneWireless Adapter The OWA 100 Adapter is designed with an OneWireless interface to allow wired HART devices to operate in a compatible distributed OneWireless system. The adapter will interoperate with any OneWireless-registered device and provide the HART diagnostic and process information to any ISA100.11a compliant system. The OWA 100 Adapter includes OneWireless electronics for operating in a 2.4GHz network.
2. Specifications 2.1. European Union Usage 2. Specifications 2.1 European Union Usage This product may be used in any of the following European Union nations.
2. Specifications 2.2. Certifications and approvals 2.2 Certifications and approvals OneWireless Adaptor Refer to product label for applicable ratings. Approval / Item Ratings / Description CSA IS - Cl I, Div. 1, Gp ABCDEFG; T4 (–40°C ≤ Ta ≤ +85°C); DIP Cl II, Div. 1, Gp EFG, CL III, Div. 1; T4 (–40°C ≤ Ta ≤ +85°C); Type 4X Intrinsically Safe CSA Non-Incendive FM Approvals Intrinsically Safe FM Approvals Nonincendive FM-ATEX 10.xxxxX Intrinsically Safe FM-ATEX 10.xxxxX Non Sparking IECEx-FM10.
2. Specifications 2.3. Agency compliance information For detailed OWA 100 Adapter specifications see the following Specification and Model Selection Guide. OWA 100 Adapter (document 34-XY-03-43) Provisioning Device Install the Provisioning Device application on any PDA having 2.3 Windows Mobile version 4.2+ Infrared port.
2. Specifications 2.3. Agency compliance information Radio Frequency (RF) statement To comply with FCC’s and Industry Canada’s RF exposure requirements, the following antenna installation and device operating configurations must be satisfied. This device must not be co-located with any other antenna or OWA 100 Adapter device and have a separation distance of at least 20cm from all persons.
2. Specifications 2.4. Honeywell European (CE) Declaration of Conformity (DoC) 2.4 Honeywell European (CE) Declaration of Conformity (DoC) This section contains the European Declaration of Conformity (DoC) statement for the OWA 100 OneWireless Adapter. R&TTE Directive 1999/5/EC EMC Directive 2004/108/EC ATEX Directive 94/9/EC Standards Applied EN 300 328 V1.7.1 Emissions Specification EN301 893 V1.4.1 Emissions Specification and Method EN 301 489-17 V1.2.
2. Specifications 2.4. Honeywell European (CE) Declaration of Conformity (DoC) European Declaration of Conformity statements 8 Language Statement Česky (Czech): Honeywell tímto prohlašuje, že tento OWA 100 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk (Danish): Undertegnede Honeywell erklærer herved, at følgende udstyr OWA 100 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
2. Specifications 2.5. IECEx Conditions of Certification: Language Statement postanowieniami Dyrektywy 1999/5/EC. Português (Portuguese): Honeywell declara que este OWA 100 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko (Slovenian): Honeywell izjavlja, da je ta OWA 100 v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
3. Configuration 3.1. Ssfety Messages 3. Configuration 3.1 Ssfety Messages These instruction procedures may require special precautions to ensure the safety of the personnel performing the operations. Information that potentially raises safety issues is indicated by a warning symbol ( ). Please refer to the following safety messages before performing an operation preceded by this symbol. WARNING Warnings Failure to follow these instructions could result in death or serious injury.
3. Configuration 3.1 Safety Messages These instruction procedures may require special precautions to ensure the safety of the personnel performing the operations. Information that potentially raises safety issues is indicated by a warning symbol ( ). Please refer to the following safety messages before performing an operation preceded by this symbol.
3. Configuration 3.2. Installation 3.2 Installation 3-1 1. Loosen the four M4 screws to remove the cover, (See Figure 5-1) If a new battery needs to be installed follow the directions for Replacing the Battery in Section 5.2. If a battery is installed remove the shipping tag between the battery and battery holder and replace the cover. 2. Remove termination cover to which the adapter is to be connected. 3. Remove plastic protective cover on adapter hub 4.
3. Configuration 3.3. Connecting to network -002 50050078-001 Figure 3-3 3.3 Connecting to network Before the adapter can be configured it must be unlocked with a security key so it can join the network. Use the Provisioning Device Pocket PC software to receive security keys from the Key Server manager, then aim the Pocket PC at the OWA 100 Adapter and transmit a key. Use Provisioning Device to connect your OWA 100 Adapter to the OneWireless network. See page X.
3. Configuration 3.4. Configuration 3.4 Configuration The OWA 100 Adapter contains the electronics interface compatible for connecting to the OneWireless network. An operator uses the Wireless Builder application to configure blocks and to change operating parameters. These changes are written to the OWA 100 Adapter when it is authenticated by a security key. No local configuration of device is required.
3. Configuration 3.4. Configuration NOTE: A passive loop exists when the wired device is not supplying power to the 4-20mA loop. It is important to verify if the wired device is operating in the active or passive mode. Figure 3-6 OWA 100 – 4-WIRE PASSIVE DEVICE CONFIGURATION NOTE: A passive loop exists when the wired device is not supplying power to the 4-20mA loop. It is important to verify if the wired device is operating in the active or passive mode.
3. Configuration 3.4. Configuration NOTE: An active loop exists when the wired device is supplying power to the 4-20mA loop. It is important to verify if the wired device is operating in the active or passive mode. Figure 3-8 OWA 100 – 4-WIRE ACTIVE DEVICE CONFIGURATION Figure 3-9 OWA 100 – 4-WIRE ACTIVE DEVICE CONFIGURATION WITH NO 4-20 mA LOOP Rev.
3. Configuration 3.4. Configuration Figure 3-10 OWA 100 – AS A ROUTER, NO WIRED DEVICE Figure 3-11 OWA 100 – AS A ROUTER, NO WIRED DEVICE 16 OWA 100 Adapter User Manual Rev.
3. Configuration 3.4. Configuration Figure 3-12 OWA 100 – 4-WIRE ACTIVE DEVICE CONFIGURATION WITH NO 4-20 mA LOOP Figure 3-13 REMOTE INSTALLATION Rev.
3. Configuration 3.4. Configuration Is this meant to be a blank page? 18 OWA 100 Adapter User Manual Rev.
4. Operation 4.1. Overview 4. Operation 4.1 Overview OWA 100 Adapter display modes The OWA 100 Adapter contains one Red LED and one Green LED that are used to indicate status. 4.2 1. No Lights = No Power (No battery power and no 4-20 mA scavenging power) 2. Steady Red = No Key 3. Steady Red, Slow Blinking Green = Discovery in Progress 4. Steady Green, Slow Blinking Red = Securing in Progress 5. Slow Blinking Green = Unit is connected to OneWireless System 6.
4. Operation 4.2. OWA 100 Adapter connection status Displayed status Definition What to do 4 Transmitter has connected with the network and is validating its key. Wait for connection. If Transmitter does not make a connection within five minutes, see NOT CONN in this table. 5 Transmitter has validated the key and has made a secure connection with at least one infrastructure node For units with radio firmware build 53 or Normal higher: No action required.
4. Operation 4.3. Provisioning device menus 4.3 Provisioning device menus Overview Hold the Provisioning Device no more than 6” (15 cm) from the OWA 100 Adapter and aim the infrared beam at the OWA 100 Adapter window while tapping on the screen command or button. Main menu The main menu is shown below. Details start on the next page. Figure 4-1 Main menu Rev.
4. Operation 4.3. Provisioning device menus Security and Node Deployment Use this to: receive new security keys, transmit security keys for connecting the OWA 100 Adapter (or other nodes) to the OneWireless network, clear all security keys from the PDA, clear the OWA 100 Adapter’s key and reset its configuration to factory default (such as for decommissioning). Figure 4-2 Security and Node Deployment 22 OWA 100 Adapter User Manual Rev.
4. Operation 4.3. Provisioning device menus To connect your OWA 100 Adapter to the OneWireless network perform the following steps. Step 1 Action If the PDA contains no keys, obtain new security keys from the PC application Key Server Manager. To do this, select Receive Security Keys. Keys can be received either through Infrared (by aiming PDA at the infrared dongle) or through an ActiveSync/USB connection. See Key Server Communication Method under Advanced options on page 27 for details.
4. Operation 4.3. Provisioning device menus Device Local Configuration Use Device Local Configuration buttons (Table 2) to navigate the OWA 100 Adapter menus (Table 1) and to make selections and changes. You can also use the PDA buttons. Figure 4-3 Device Local Configuration screen Table 2 Buttons for Device Local Configuration Button Function Enter the Menu Tree. Enter submenu of the menu that is appearing on the screen. Execute action. Submit the entered number while doing number entry.
4. Operation 4.3. Provisioning device menus Read Node Information Use this to read the OWA 100 Adapter’s information shown in Figure 4-4. Similar to quick view parameters on the OWA 100 Adapter display. (See Table 2) Replace table 3 per Figure 4-4 Read Node Information next page Table 3 Read Node Information Item Description Tag The name given to this OWA 100 Adapter Serial OWA 100 Adapter serial number. This is the WBSN on the OWA 100 Adapter’s nameplate.
New Table 3 part 1 4. Operation 4.3. Provisioning device menus Item Connection Description The first line displays one of the following connection states. No Security Key – No security key has been deployed to the device or multinode. The user must give a security key to the device or multinode before it will join the wireless sensor network. No Connection – A security key exists in the device or multinode, but no connection has been formed.
4. Operation 4.3. Provisioning device menus Advanced Options Advanced options are non-typical configuration commands. Figure 4-5 Advanced Options Rev.
4. Operation 4.3. Provisioning device menus Table 4 Advanced Options Item Key Server Communication Method Description Determines how the PDA will receive security keys from the PC’s Key Server Manager application. From the Comm Method menu select one of the following methods. ActiveSync – Select this to receive keys over a USB connection, such as while the PDA battery is being charged in its base. Infrared – Select this to receive keys over the infrared port.
5. Maintenance/Repair 5.1 Parts The following replacement parts may be ordered from Honeywell. Part number Qty. Description 50056644-501 1 REMOTE MOUNTING KIT FOR 1/2 NPT OWA 100 ADAPTER 50056644-502 1 REMOTE MOUNTING KIT FOR M20 OWA 100 ADAPTER 30671907-001 1 PIPE MOUNT BRACKET KIT (SS) FOR MOUNTING OWA 100 ADAPTER 50026010-001 2 3.6V LITHIUM THIONYL CHLORIDE (Li-SOCI2) BATTERY 50026010-002 4 3.6V LITHIUM THIONYL CHLORIDE (Li-SOCI2) BATTERY 50026010-003 10 3.
SHOCK HAZARD Depending on your installation, OWA 100 Adapter input wiring sources may contain high voltage. Disconnect all power from OWA 100 Adapter input sources before accessing the batteries. Failure to do so could result in death or serious injury if the input terminals or wires are accidentally touched. Figure 5-1 Battery replacement 30 OWA 100 Adapter User Manual Rev.
Table 5 Battery replacement procedure Step Action ATTENTION Use only the following 3.6V lithium thionyl chloride (Li-SOCl2) batteries (non-rechargeable), size D. No other batteries are approved for use in OWA 100 Adapter. Xeno Energy XL-205F Eagle Picher PT-2300H Tadiran TL-5930/s 1 Loosen (4) M4 screws and remove the cover. 2 Remove the old battery from the battery holder. If needed, pry out the battery by using a slotted screwdriver as a lever.
6. Certification Installation Requirements 6.1 Certification Drawings Use the following drawings and accompanying notes and text for hazardous locations. Any deviation from the installation requirements could void the certification. For non-hazardous locations you can use the same drawings without the accompanying notes and text. 32 OWA 100 Adapter User Manual Rev.
Rev.
34 OWA 100 Adapter User Manual Rev.
Rev.
36 OWA 100 Adapter User Manual Rev.
Rev.
7. Reference Data 7.1 Product Specifications Operating Conditions Parameter Reference Condition °C Ambient Temperature** 25 ±1 Humidity (%RH) Rated Condition Operative Limits Transportation and Storage °F °C °F °C °F °C °F 77 ±2 -40 to 85 -40 to 185 -40 to 85 -40 to 185 -40 to 85 -40 to 185 10 to 55 0 to 100 Vibration Maximum of 4g over 15 to 200 Hz Shock Maximum of 40g 0 to 100 0 to 100 Battery powered 3.
CSA IS – ENTITY - Cl I, Div. 1, Gp ABCDEFG; T4 (–40°C ≤ Ta ≤ +85°C); DIP Cl II, Div. 1, Gp EFG, CL III, Div. 1; T4 (–40°C ≤ Ta ≤ +85°C); Type 4X; IS – ENTITY - Cl I, Zone 0; Ex ia IIC, T4 (–40°C ≤ Ta ≤ +85°C); IP66 Hazardous Location Certifications CSA NI - Cl I, Div. 2, Gp ABCD; T4 (–40°C ≤ Ta ≤ +85°C); DIP A22, Cl II, Div. 2, Gp FG; CL III, Div. 2; T4 (–40°C ≤ Ta ≤ +85°C); Type 4X; NI - Cl I, Zone 2; Ex nA IIC, T4 (–40°C ≤ Ta ≤ +85°C); Type 4X FM Approvals IS – ENTITY - Cl I, Div.
Sales and Service For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one of the offices below. Asia Pacific Global Technical Support Field Instruments Phone: +65 6580 3156 Fax: +65 6445-3033 Australia Honeywell Limited Phone: +(61) 7-3846 1255 FAX: +(61) 7-3840 6481 Toll Free 1300-36-39-36 Toll Free Fax: 1300-36-04-70 China – PRC - Beijing Honeywell China Inc.
