Connected Freight Quick Start Guide Rev (a) 5/17
This document covers the following models: • 3G-ST-THALP-C1 Gateway • RTHAL-C1 Tag 1
STEP 1: Gather Materials $ ( , " $ * ,/ 5:9 " ) / " 5 " $(" # # / " # ( 4 # ) " " $ ( $ $ # " $ # $1 $ ,# !( %$, $ $ * , $ # #$ $ ( $ #$ $ $ # ( $ 239 Waybill 239 Shipping # 123456 7 8910 16348D80F6 2
STEP 2: Check Gateway Battery Status #% ( / " $ $ $ ' ", # ,# " $5 $ # $ # ( " Fully charged Solid green 16348D80F6 Charging Solid red 16348D80F6 Faulty Battery OR Battery Has No Charge Left Alternately blinking red and green 16348D80F6 If Battery has no charge left, the Gateway needs 15-20 minutes to precharge, before the battery starts charging normally.
STEP 3: Pair Gateway With Tags Before They’re Powered On Pair each tag to the gateway by holding the gateway pairing button and tapping the tag to the gateway, verifying a successful pairing has occurred each time (see user guide). Successful Pairing NFC button solid green Failed Pairing NFC button blinks red 16348D80F6 F6 6 Short beep x Long beep The Tag LED light will not display, because the Tag is not powered on.
STEP 4: Apply Shipping Labels to Box 5
STEP 5: Turn on Tag Battery ) $ ' ", #$" # " $ ) " , $ , " * " 7# (# " ( 81 " ) $ " #% " " $ $ $ $ # $ el & stick p peel & stick p peel & stick p peel & stick p peel & stick p peel & stick ck peel & stick peel & stick peel & stick peel & stick peel & stick peel & el & stick peel & stick peel & stick peel & stick peel & stick peel & stick ck peel & stick peel & stick peel & stick peel & stick peel & stick peel & el & st
STEP 6: Confirm Tags are Powered On Battery Activated and Tag Paired with Gateway LED blinks red 3 times, then blinks green once, then turns off. E0023D7304090A6A x3 X x1 Bad Tag No LED indicator STEP 7: Attach Tags to Shipment Then remove the large sticker backing and adhere the tag to the shipment.
STEP 8: Launch and Refresh Movilizer App 6 $ ) - " $ $5:9 " ) 1 6 $ " " # (' $ $ ' $ 7$* "" *#8/ $ # , $ #$ ("" $ # $ " % 1 6 $ # " # " " # 7$ ( # ( 81 $ 0 " ) - " # ) " $ ) #( $" $ $#/ ($ $ # # " # 4 " ##1 8
STEP 9: Select Shipment Click the “Shipments – OBD” icon and locate the Shipment ID under the “New Shipments:” list and click it 9
STEP 10: Review Shipment Info Review the basic shipment information, route, monitoring and all other info to ensure it is correct against the information available to you on the shipping document.
OPTIONAL STEP View Instructions Click “View Instructions” for step-by-step information and video tutorials on how to set up shipments with Gateways & Tags.
STEP 11: Pair Gateway With Shipment Click the “Scan Gateway” button at the bottom of the screen and scan the barcode on the gateway using the rear facing camera on the mobile device. This pairs the Gateway with the Shipment for tracking purposes.
STEP 12: Confirm # of Tags and Find Tag Scanning the Gateway will bring up the list of tags you already connected to the gateway Verify that the correct number of tags are listed here. Find the shipment Tag.
Step 13: Pair Tags With Boxes / Pallets Find the tag ID in the OBD app tag list and click on it, this will bring up a scanner. Scan the unique box/ pallet barcode ID where you attached your tag. This pairs the Tag with the box or pallet it’s on, to identify which Traceable Shipping Unit (TSU) has been compromised if a sensor limit is exceeded. Repeat until all tags are associated.
STEP 14: Review Shipment Data & Complete Shipment +$ " ) * $ $ # "" $ $ # $1 2 $ $13 15
STEP 15: Attach Gateway to the Box or Pallet $ $ * ,/ # ( $ " " $(" # $ # $ ) 1 E0023D7304090A6A 16
Discuss Shipment Loading Requirements When loading pallets with Tags and Gateways onto a truck, try to place one pallet in the back of the truck, one pallet in the center of the truck and one pallet with the Gateway right by the door. Make sure that the Gateway faces the truck door, and is as close to the door as possible to ensure the Gateway signal can best maintain cell connectivity.
Support To search our knowledge base for a solution or to log into the Technical Support portal and report a problem, go to www.hsmcontactsupport.com. User Documentation For the user guide and other documentation, go to www.honeywellaidc.com. Limited Warranty For warranty information, go to www.honeywellaidc.com and click Get Resources > Product Warranty. Patents For patent information, see www.hsmpats.com.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results. This document contains proprietary information that is protected by copyright. All rights are reserved.