Installation Instructions

ManualsBrandsHoneywell International ManualsElectronicse7w Wireless EMS Thermostat

1 31-00308–01

e7w Wireless EMS Thermostat

INSTALLATION INSTRUCTIONS

FOR ALL UNITS IN CARTON. DO NOT THROW AWAY!

INSTALLATION REQUIREMENTS

Required Installation Hardware

• Four 6-32 × 1.5” Philips Pan head screws (provided with e7w) if attaching to a 4X4 electrical junction

box.

• Four AA alkaline batteries; provided with e7w.

• e7w Smart Wall Mounting Plate; provided with e7w.

• Three 4-24 1/2’’ Phillips screws Phillips captive screws; provided with e7w.

• Phillips Screwdriver.

• Wire cutters/strippers.

Required Commissioning Tools

DO NOT THROW THIS UNIT AWAY: One PC-503 USB Commissioning Tool and USB cable per property/project

is shipped to the site.

This tool is used in conjunction with Honeywell's engINN commissioning software when advanced commis-

sioning of the e7w is required by a trained and certified INNCOM technician. Contact Honeywell technical sup-

port for more information.

Figure 1: PC-503 USB commissioning tool and cable

Summary of content (12 pages)

PAGE 1
e7w Wireless EMS Thermostat INSTALLATION INSTRUCTIONS FOR ALL UNITS IN CARTON. DO NOT THROW AWAY! INSTALLATION REQUIREMENTS Required Installation Hardware • Four 6-32 × 1.5” Philips Pan head screws (provided with e7w) if attaching to a 4X4 electrical junction box. • Four AA alkaline batteries; provided with e7w. • e7w Smart Wall Mounting Plate; provided with e7w. • Three 4-24 1/2’’ Phillips screws Phillips captive screws; provided with e7w. • Phillips Screwdriver. • Wire cutters/strippers.
PAGE 2
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS CAUTION • Read instructions carefully. Failure to follow them could damage the product or create a hazard. • Check the ratings given in the instructions and on the product to ensure that the product is suitable for your application. • Installer must be a trained, experienced service technician. • After installation is complete, check product operation as indicated in instructions.
PAGE 3
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS a. Verify that the batteries installed in correct terminal. Battery Details b. Check the battery voltage. 6. Hook the tabs at the top rear of the e7w housing into the matching depressions at the top of the Smart Mounting Plate and rotate the bottom of the housing toward the wall until it snaps into place. 7.
PAGE 4
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS Specifications Mounting Standard US Double Gang: w/o Spacer Ring Standard US Single Gang: w/o Spacer Ring Standard UK Single Gang: w/o Spacer Ring Dimension L 120mm x W 120mm x H (23) mm (w/o spacer) Ambient Operating 41 to 149 °F (5 to 40 °C), 0-95% RH non-condensing Ambient Storage 33 to 149 °F (1 to 65 °C) C/F degrees display Toggle Button located on front display. In room Temperature 60°F to 85°F (± 1°F) [15°C to 30°C (± 0.
PAGE 5
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS Wireless Communications Parameter Description Encryption AES -128 RF Data Rate 250kbps Protocol 802.15.4 Antenna Type SMT Frequency Channels 11-26 Indoor range 70ft Transmit Power +5dBm Receive Sensitivity -95dBm Frequency Band 2.4Ghz Note: • Required Deep Mesh Network 2.4GHz. LCD Display Figure 5.
PAGE 6
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS INITIAL SETUP Note: Before going through the initial setup sequences, ensure the thermostat is mounted and connected to the Smart Wall. Note: The five-digit number is comprised of three fields: highest digit, middle two digits, lowest two digits (HIMEDLO), default value (65535). Three settings must be made. − When properly connected, the thermostat will proceed into INTIALIZATION MODE and display rId. 2.
PAGE 7
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS Setup RF Channel Setup PAn ID Figure 8. Setup RF Channel Figure 10. Setup PAn ID 1. After rF is displayed, press MODE. After PAn is displayed, press MODE. 2. Default rF value 26 displayed on the screen. 1. Default PAn value is 0 displayed on the screen. 3. Use the UP/DOWN arrows to change value range between 11 to 26. 4. Press FAN, the unit beeps to confirm the value stored in the memory and display will be back rF. 5.
PAGE 8
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS BINDING AUXILIARY DEVICES 3. Use the UP/DOWN arrow buttons to change the displayed value range from 0 to 255. Set the Io value to the desired I/O map number. Note: Before binding or verifying auxiliary devices. • e7w must be configured with correct Room ID, PAN ID, and RF Channel. • For forward bind method, place the remote device into a discovery mode that can receives the request sent from the thermostat and reply to the request.
PAGE 9
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS STANDARDS AND APPROVALS Note 1 EN • Product Standard − EN 60730-1:2011 and EN 60730-2-9:2010 (covers EMC and LVD Safety requirements). • EMC Standard − ETSI 301489-1 V2.2.1, ETSI 301 489-17 V 3.2.0. • EMC Standard EN 55032 − Radiated RF Emissions. UL (IEC) • UL 60730-1, 5th edition and UL 60730-2-9, 4th edition.
PAGE 10
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
PAGE 11
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS WEEE Directive 2012/19/EC Waste Electrical and Electronic Equipment Directive The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. Dispose of the packaging and this product in an authorized collection or recycling center. Do not dispose of the unit with domestic refuse. Do not incinerate.
PAGE 12
e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS The material in this document is for information purposes only. The content and the product described are subject to change without notice. Honeywell makes no representations or warranties with respect to this document. In no event shall Honeywell be liable for technical or editorial omissions or mistakes in this document, nor shall it be liable for any damages, direct or incidental, arising out of or related to the use of this document.