Foxconn WFUR6 Foxconn WFUR6 Hardware Specification Rev. 0.
Foxconn WFUR6 Document Revision History Document Revision Date Modifier Comments 0.1 Dec. 30, 2013 Lin Eric Initial release 0.2 Feb.
Foxconn WFUR6 Contents 1. INTRODUCTION ............................................................................................ 5 1.1 Product Overview ............................................................................................. 5 1.2 Key Features ..................................................................................................... 5 2. ELECTRICAL SPECIFICATIONS.......................................................................... 6 2.1 Pin Definitions .............
Foxconn WFUR6 7. MODULE PHOTO .........................................................................................
Foxconn WFUR6 1. Introduction 1.1 Product Overview The Foxconn WFUR6 wireless LAN module contains the Realtak® RTL8812AU single chip which is a highly integrated single‐chip MIMO (Multiple In, Multiple Out) Wireless LAN (WLAN) USB 2.0 network interface controller complying with the wireless very high throughput IEEE 802.11ac Draft 2.0 and 802.11n specifications. It fully complies with IEEE 802.
Foxconn WFUR6 2. Electrical Specifications 2.1 Pin Definitions Table 2.1 Pin Definitions Pin # Name Pin # Name 51 N/A 52 +3.3V 49 N/A 50 GND 47 N/A 48 N/A 45 N/A 46 N/A 43 GND 44 N/A 41 +3.3V 42 N/A 39 +3.
Foxconn WFUR6 2.2 Power Consumption Specifications Power consumption is measured using current probe loop on the Power rails of the USB interface (Pins). Table 2.
Foxconn WFUR6 3.RF Specification 3.1 TX Specifications (preliminary) Table 3.1 TX Specifications Target Power(dBm) Tolerance(dB) Chain 0/Chain 1 802.11a 13 +1.5/-2 802.11ac(20MHz) 14.5 +/-1.5 802.11ac(40MHz) 14 +/-1.5 802.11ac(80MHz) 12 +/-2 801.11b 16 +/-2 802.11g 15 +/-2 802.11n(20MHz) 14 +/-2 802.11n(40MHz) 13.5 +/-2 3.2 RX Specifications (preliminary) Table 3.2 RX Specifications (ANT 1 & ANT 2) Data Rate (Mbps) Modulation 1 Rx Sensitivity (dBm) Data Rate (Mbps) Max. Typ.
Foxconn WFUR6 24 OFDM ‐77 ‐82 HT40‐15 BPSK ‐79 ‐87 36 OFDM ‐73 ‐79 HT40‐30 QPSK ‐76 ‐84 48 OFDM ‐69 ‐75 HT40‐45 QPSK ‐74 ‐81 54 OFDM ‐68 ‐74 HT40‐60 16‐QAM ‐71 ‐79 HT40‐90 16‐QAM ‐67 ‐74 HT40‐120 64‐QAM ‐63 ‐71 HT40‐135 64‐QAM ‐62 ‐70 HT40‐150 64‐QAM ‐61 ‐68 HT80‐32.5 BPSK ‐76 ‐83 HT80‐65 QPSK ‐73 ‐83 HT80‐97.5 QPSK ‐71 ‐81 HT80‐130 16‐QAM ‐68 ‐77 HT80‐195 16‐QAM ‐64 ‐74 HT80‐260 64‐QAM ‐60 ‐70 HT80‐292.
Foxconn WFUR6 3.3 Antenna Specifications Nominal antenna port impedance specification is 50 ohms for the Foxconn WFUR6 hardware. For regulatory requirements, it is assumed that the antenna gain is: Antenna gain for the 2.4GHz band : 3.47 dB Antenna gain for the 5GHz band : 4.66 dB There are two antennas supporting 2.4~2.5GHz band and 5.15~5.85GHz. The antenna will be defined ANT 1 and ANT 2 where is listing below: Figure 4.
Foxconn WFUR6 4. Mechanical Specifications 4.1 Mechanical Drawing Figure 4.
Foxconn WFUR6 4.2 RF connector Manufacturer: Speed tech Manufacturer P/N: C88P132‐01001‐H 4.2.1 Specification Operating temperature range: ‐40℃~90℃ Storage temperature range: ‐40℃~90℃ Characteristic impedance: 50Ω (0~3GHz) Voltage standing wave ratio: 1.3 max. at 2.4GHz, 1.4 max. at 6GHz 4.2.2 Dimensions: (Unit: mm) Figure 4.2 RF connector dimensions 4.3 Label Specifications 24mm 17mm Figure 4.
Foxconn WFUR6 5. Environmental Specifications The following tables provide normal operating conditions and maximum rating requirements for WFUR6 hardware. Table 5.1 Operating Conditions (preliminary) Environment Limits Operating 0 ~ 60℃ ※The radio parts at operating state and above temperature of T‐shield. Table 5.2 Non‐operating Conditions (preliminary) Environment Non‐Operating Temperature Humidity Min. Typ. Max. Unit Min. Typ. Max.
Foxconn WFUR6 6. Part Numbering 6.1 ID Definitions Table 6.1 ID Definitions WLAN Type Realtek RTL8812‐AU LAN 802.11n usb2.
Foxconn WFUR6 7.
Foxconn WFUR6 Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user＇s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules.
Foxconn WFUR6 Industry Canada Statement This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Foxconn WFUR6 Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. End Product Labeling When the module is installed in the host device, the FCC/IC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re‐moved.
