PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Ambit PCI Full Rate ADSL Modem Installation Manual For Windows 95, 98, and NT4.0 Dec 16, 1999 Date Printed: 12/20/99 Page 1 Man_A2.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Table of Contents ABOUT THIS G UIDE 1.INTRODUCTION......................................................................................................................................................3 SYSTEM REQUIREMENT .............................................................................................................................................. 4 Hardware Requirement...................................................................
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 1. INTRODUCTION The Ambit PCI Full Rate ADSL Modem is an internal ADSL modem, which conveniently plugs into a PC system, eliminating the need for an external modem. The Ambit PCI ADSL Modem connects to a telephone line via a standard RJ-11 connector and fully complies with practices governing the PC world (e.g. Plug 'n Play).
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 System Requirement The following equipment and information is required (at a minimum) to setup your ADSL network modem. Hardware Requirement The following is the minimum hardware requirement. Please make sure your PC system meets ALL of the following requirements.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Before you start: Ambit ADSL Modem Installation & Configuration Flow Chart Insert Ambit ADSL card Connect the card to ADSL network Installing driver and application programs Reboot and verify last step Configure ADSL network Reboot and activating Ambit ADSL modem Date Printed: 12/20/99 Page 5 Monitoring the Ambit ADSL modem Man_A2.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 2. INSTALLING THE ADSL NETWORK MODEM BOARD To install the Ambit PCI Full Rate ADSL Modem in your PC and connect it to ADSL network, follow these steps: Insert ADSL Network Interface Card – Step 1 1) Open the shipping container and inspect each item for damage. 2) Remove all jewelry from your hands and wrists. Use only insulated or nonconductive tools. 3) Unplug the PC and disconnect all cables. 4) Remove the PC cover.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 3. INSTALLING THE AMBIT PCI DEVICE DRIVERS AND UTILITY Please have the following information available in order to complete the installation and setup of the Ambit PCI ADSL Modem. 1. 2. TCP/IP properties, this includes the PVC values (VPI and VCI), IP address, the gateway, and the domain name server. You will need this information to complete the configuration of the network modem card.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 The Add New Hardware Wizard window will appear. When prompted, select "Search for the best driver for your device. (Recommended)". Click "Next". If your Ambit PCI ADSL Modem comes with floppy diskettes, then insert the Windows 98 driver diskette (use the Windows 98 2nd edition diskette for installing on Windows 98 2nd edition and the Windows 98 diskette for installing on Windows 98 1st edition) into the floppy disk drive.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Windows should find the *.INF (NETITEX.INF for Windows 98 2nd edition) file in the directory specified. Click "Next" to continue. Windows will start to copy the drivers. Make sure that the Windows 98 CD is in the CD-ROM or that it is easily accessible. Date Printed: 12/20/99 Page 9 Man_A2.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 For RFC1483, the default PVC values are 8 and 35 for VPI and VCI respectively. If necessary, these values can be changed at this time. The range for both VPI and VCI is from 0 to 255. Windows has finished installing all the Ambit ADSL Modem drivers. Click "Finish" to complete the installation. Click "Yes" when prompted "Do you want to restart your computer now?" If you are using floppy diskettes, remove the floppy diskette from the diskette drive.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 3.2 Windows 95 * BEFORE YOU START: You need the Windows 95 system installation files to complete the installation. This section describes how to install the network driver when your PC is running Windows 95.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 For RFC 1483, the default PVC values are VPI=8 and VCI=35 respectively. If necessary, these values can be changed at this time. The range for both VPI and VCI is 0 to 255. For more detailed information regarding the values of VPI and VCI, please check with your ADSL service provider. CAUTION: Failure to setup the right VPI, VCI may cause the ADSL network to fail. Follow the screen instructions until Windows 95 asks you to restart your computer.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 4. Verifying the Driver Installation 4.1 Windows 95 and Windows 98 From the Start menu, select settings and open the control panel. Double click on the Network Icon.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Windows 95 § ITeX ADSL Network Modem (Apollo 2 - 8MB/s) § ATM Call Manager à ITeX ADSL Network Modem (Apollo 2 - 8MB/s) § TCP/IP Click "Cancel" to close the Network window. 4.2 Windows NT 4.0 Double-click the Network icon. The network dialog window appears. In the Network dialog window, select the Configuration tab.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Select the Configuration Tab and scroll through the installed network component list. For Windows 98 2nd Edition, highlight the TCP/IP à ITeX RFC1483 Ethernet Adapter component. For Windows 98 1s t Edition, highlight the TCP/IPàITeX ADSL Network Modem (Ambit PCI 8Mbps). For Windows 95, highlight "TCP/IP". Click "Properties.” The TCP/IP Properties window will appear.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 To setup a new gateway, enter the setting in the new gateway section and click "Add.” This will add the setting into the installed gateways. To configure the Domain Name Server, simply select the Enable DNS option. Enter the Host and Domain settings. Enter the DNS Server search order and click "Add.” Once all the TCP/IP properties have been set, click "OK" to return to the Network window. Date Printed: 12/20/99 Page 16 Man_A2.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Click "OK" to close the Network window. Click "No" when prompted "Do you want to restart your computer now?" SETTING THE PVC VALUES FOR ETHERNET OVER ATM (RFC1483) Windows 98 2nd Edition For RFC1483, the VPI and VCI have a default setting of 8 and 35 respectively. To change the values for RFC1483, follow these instructions: Using the Modem Icon Utility to Set the PVC Values Refer to "User's Guide to the Modem Icon Utility" for more information.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 5.2 Windows NT4.0 Ethernet over ATM (RFC1483) Open the Network dialog window by double clicking My Computer->Control Panel->Network. In the Network window, select the Adapters tab. Scroll through the installed network components list. Highlight the "ITeX ADSL Network Modem (Apollo 2 - 8Mbps)" and click Properties. The TCP/IP Properties window appears. Please check your TCP/IP configuration with your Internet service provider.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 To setup a new gateway, enter the setting in the new gateway section and click "Add.” This will add the setting into the installed gateways. To configure the Domain Name Server, simply select the Enable DNS option. Enter the Host and Domain settings. Enter the DNS Server Search Order and click "Add.” Once all the TCP/IP properties have been set, click "OK" to return to the Network window. Date Printed: 12/20/99 Page 19 Man_A2.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 Click "OK" to close the Network window. Click "Yes" when prompted "Do you want to restart your computer now?" 6. ACTIVATING THE AMBIT PCI ADSL NETWORK MODEM For RFC1483 : Once the drivers are installed and the setup is complete, the Ambit ADSL Modem is ready to run. Each time the computer is turned on, the modem automatically connects to the central office equipment. Simply run the internet browser software to verify. 7.
PCI Full Rate ADSL Modem Driver Installation A2RAI-081699 • Right click on the “My Computer” icon; select Properties; select Device Manager; Scroll down to "Network Adapters.” Open the "Network Adapters" folder. • Right click "ITeX A2 ADSL NIC" and click "Remove.” Click "OK" when prompted with a warning about removing and adapter. Click "OK" to close the Systems window.
