U S E R’S M A N J20H049 USB2.
Contents SECTION ONE: INTRODUCTION ............................................................................................ 3 1.INTRODUCTION ................................................................................................................................ 3 1.1 SCOPE ........................................................................................................................................... 3 1.2 FUNCTION .....................................................................
HON HAI PRECISION IND. CO., LTD. Section one: Introduction 1.Introduction Project Name: 802.11b/g/n (1x1) card based on IC Atheros AR9271(UB91) with QFN package. 802.11b/g/n module provides wireless modem functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. The typical use model for this embedded device is to allow the host device to be connected to an 802.11b/g/n 1x1 wireless network with infrastructure mode or to serve as an ad-hoc (peer-to-peer) data path. 1.
HON HAI PRECISION IND. CO., LTD. 2.Product Specification 2.1 Hardware Specification Wireless LAN Standards IEEE802.11b/g/n compatible ARIB STD-T66 compatible ETSI 300.328 compatible FCC 15.247 compatible FCC 15.407 compatible Operating Frequency Channel Numbers 2.400~2.4835GHz 1~11 channels active 12,13 channels passive 14 channels no need 802.11g: 54Mbps with fall back of 48, 36, 24, 18, 12, 9, 6Mbps. 802.11b: 11Mbps with fall back rates of 5.5, 2, and 1Mbps 11n: 6.5, 13, 19.5, 26, 39, 52, 58.
HON HAI PRECISION IND. CO., LTD. 3. Product Requirements 3.1 Hardware Requirements Host Interface PCB Antenna port: USB 2.0 2-layer FR4 ANT1 for TX/RX , ANT2 for RX Diversity 3.2 Hardware Architecture This specification describes an embedded 802.11b/g/n WiFi interface PCA ‘module’ for embedded device products. The module has two on-board connector. This module is powered from the host (5.0V) and interfaces to the host with USB 2.0 signals.
HON HAI PRECISION IND. CO., LTD. 4 FCC Notice Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
HON HAI PRECISION IND. CO., LTD. The users manual for OEM integrators must include the following information in a prominent location “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
HON HAI PRECISION IND. CO., LTD. 5 Canada Notice Industry Canada Statement Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.
HON HAI PRECISION IND. CO., LTD. Section Two: Windows XP Wireless Utility and install 1. Open your Install Programs files folder or InstallCD and double Clicked the file named“setup.exe”. 2. You can see next interface, press “next” 3.
HON HAI PRECISION IND. CO., LTD. 4.
HON HAI PRECISION IND. CO., LTD. 5. You will see next two interfaces and they will direct you to select the the destination location.
HON HAI PRECISION IND. CO., LTD. 6. you can see this interface and the note will tell you how to select in the second interface.
HON HAI PRECISION IND. CO., LTD. 7.the program will reboot the system before working, and click“ yes” 8.the warning prompt you to inert your client adapter before install the program. 9.
HON HAI PRECISION IND. CO., LTD. 10.