User's Manual

ManualsBrandsHON HAI Precision Ind ManualsElectronicsLoRa Express Gateway

GPE810U

Confidential Page 1

Indoor LoRa Gateway

Quick Setup Guide

(GPE810U)

1. Introduction

LoRa indoor gateway is designed to meet the needs of IoT services. This indoor gateway

allow the users to setup this in indoor environment as an aggregator of LoRa sensors to the

internet for the related services. Tomorrow's connected devices will control everything from

indoor temperatures to air conditioner, from the flow of energy through our cities to the flow

of critical healthcare data, unlocking hidden value in unconnected machines. So the

connectivity is critical to generate intelligence, except the WiFi, LoRa is also an alternatively

solution for indoor applications.

Summary of content (8 pages)

PAGE 1
GPE810U Indoor LoRa Gateway Quick Setup Guide (GPE810U) 1. Introduction LoRa indoor gateway is designed to meet the needs of IoT services. This indoor gateway allow the users to setup this in indoor environment as an aggregator of LoRa sensors to the internet for the related services.
PAGE 2
GPE810U 2. Hardware Specifications Feature Description Processor TI AM3352 ARM Cortex-A8, 1-GHz Storage 4/8GB eMMC Memory DDR3 4Gb 2.4G WiFi TI WL1831MOD b/g/n single band 2.4G 1T1R Sensor-LoRa 868 MHz Semtech FPGA+SX1301 (daughter card) External Power Jack 12V/1.5A DC_IN I/O Port 1.RJ45x1, 1 WAN 10/100/1000 2.Reset button x 1 3.USB x 1 4.SMA x 1 Dimension A x B x C mm (128.9 x 128.9 x 26.2) Weight 205g Housing Color White 3.
PAGE 3
GPE810U 4.Software setup 4.1Use web interface to setup LoRa Indoor GW under Ethernet deployment mode 4.1.1 Power up Indoor LoRa GW 4.1.2 Set PC/NB ether port IPv4 setting in user PC statically for example, 192.168.127.100. 4.1.3 Use PC/NB ether port connect to the Indoor LoRa GW Ethernet port, and then open a browser to Indoor LoRa GW’s IP (192.168.127.250) to access its web interface.
PAGE 4
GPE810U 4.2. Set WAN interface Select [WAN] page for setting WAN configuration  WiFi client can be WAN interface, and it is independent from WiFi AP mode.
PAGE 5
GPE810U 4.2.1 Select “Ethernet” as WAN Use DHCP Mode to get IP address automatically A. Set Primary WAN type as “Ethernet” B. Set Ethernet IP Type under Ethernet Settings as “DHCP” C. Press Apply button  Secondary WAN will be used when Primary WAN is dead. 4.2.3 Use static IP Mode A. Set Primary WAN type as “Ethernet” B. Set Ethernet IP Type under Ethernet Settings as “Static” C. Configure proper settings in IP address / Netmask / Gateway / Primary DNS / Secondary DNS under Static IP Settings D.
PAGE 6
GPE810U 5. Mechanical and Accessory 5.1 Wall Mount support This product may provide the optional wall mounting support due to the 3 nuts on its bottom. For this function, 3 pieces of machine screws shall be used, and the recommended spec is M3X6mm or others appropriate.
PAGE 7
GPE810U Confidential Page 7
PAGE 8
GPE810U Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.