6800-90 Ottoman IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Cushion 1 pc. B. Panel 2 pcs. C. Panel 2 pcs. D. Base 1 pc. E. Foot 4 pcs. F. Panel 1 pc. Hardware List Hex Wrench 1 pc. (+1 extra) Small Hex Wrench 1 pc.
Assembly Instructions 2/6 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Attach Base (D) to Panel (B) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/6 Flat Washer Spring Washer Head Cap Bolt C STEP 3 Attach Panel (C) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Head Cap Bolt Spring Washer Flat Washer STEP 4 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway.
Assembly Instructions 4/6 Flat Washer Spring Washer Head Cap Bolt B STEP 5 Attach Panel (B) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Head Cap Bolt Spring Washer Flat Washer STEP 6 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2, 3, 4, 5 and 6.
Assembly Instructions 5/6 Head Cap Bolt Spring Washer Flat Washer E E E E Figure 2 STEP 7 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers. (See Figure 2) Velcro Strap aaa aaa aaa aaa Velcro Strap aaa aaa aaaa aaaa F Figure 3 A STEP 8 Attach Panel (F) to Cushion (A) with velcro straps.
Assembly Instructions 6/6 A STEP 9 Turn unit over to its upright position. Place Cushion (A) into position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
6800-101 Arm Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Back 1 pc. B. Seat 1 pc. C. Side 2 pcs. E. Foot 4 pcs. Hardware List Hex Wrench 1 pc. Small Hex Wrench 1 pc. M6x35 Head Cap Bolt 24 pcs. (+1 extra) Spring Washer 24 pcs.
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 A Attach Seat (B) to Back (A) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/5 Head Cap Bolt Spring Washer Flat Washer STEP 3 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway. (See Figure 3) Figure 3 Head Cap Bolt Spring Washer Flat Washer C STEP 4 Attach unit to Side (C) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 4/5 Head Cap Bolt Spring Washer Flat Washer STEP 5 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2, 3, 4 and 5. Head Cap Bolt Spring Washer Flat Washer STEP 6 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 5/5 Toggle G Figure 5 Toggle F STEP 7 Turn over unit to its upright position. Attach Seat Cushion (F) to unit by pushing toggles through weaving in back of unit. (See Figure 5) Place Back Cushion (G) into position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
6800-58 Seating IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List O. Back 1 pc. P. Seat 1 pc. D. Frame 2 pcs. J. Clip 2 pcs. E. Foot 4 pcs. Hardware List Hex Wrench 1 pc. Small Hex Wrench 1 pc. M6x35 Head Cap Bolt 20 pcs.
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. Middle Unit O STEP 1 Attach Seat (P) to Back (O) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/5 STEP 3 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2 and 3. Flat Washer Spring Washer Head Cap Bolt D Head Cap Bolt Spring Washer Flat Washer E E E E Figure 2 STEP 4 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 4/5 For a sofa, follow instructions in 6800-57 carton, then complete Steps 5 and 6. For a 5, 6 or 7 seat sectional, follow instructions in 6800-401 and 6800-402 cartons. Sofa STEP 5 Attach left unit, middle unit and right unit with Clips (J).
Assembly Instructions 5/5 Toggle Figure 4 G G G Toggle F F F STEP 6 Three 6800-CUS cartons are also needed for this step. Turn unit to its upright position. Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit. (See Figure 4) Place Back Cushions (G) into position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
6800-401 Sectional IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Back 2 pcs. B. Seat 2 pcs. O. Back 1 pc. C. Side 2 pcs. D. Frame 4 pcs. P. Seat 1 pc. E. Foot 12 pcs. Hardware List Hex Wrench 1 pc. Small Hex Wrench 1 pc.
Assembly Instructions 2/7 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. Left Unit STEP 1 A Attach Seat (B) to Back (A) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/7 STEP 3 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2 and 3. Flat Washer Spring Washer Head Cap Bolt D Head Cap Bolt Spring Washer Flat Washer E E E E Figure 3 STEP 4 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 4/7 Right Unit A STEP 5 Attach Seat (B) to Back (A) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. B Flat Washer Spring Washer Head Cap Bolt STEP 6 Attach unit to Side (C) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 5/7 STEP 7 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 5, 6 and 7. D Flat Washer Spring Washer Head Cap Bolt Head Cap Bolt Spring Washer Flat Washer E E E E STEP 8 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 6/7 Middle Unit STEP 9 O Attach Seat (P) to Back (O) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. P Flat Washer Spring Washer Head Cap Bolt STEP 10 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 7/7 STEP 11 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 9, 10 and 11. Flat Washer Spring Washer Head Cap Bolt D Head Cap Bolt Spring Washer Flat Washer E E E E STEP 12 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers. To complete assembly, follow instructions in 6800-402 carton.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
6800-402 Sectional IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List L. Back 1 pc. M. Seat 1 pc. N. Back 1 pc. E. Foot 4 pcs. H. Seat Cushion 1 pc. I. Back Cushion 1 pc. K. Back Cushion 1 pc. J. Clip 6 pcs. Hardware List Hex Wrench 1 pc.
Assembly Instructions 2/7 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. Follow instructions in 6800-401 carton first, then proceed with Step 13.
Assembly Instructions 3/7 STEP 15 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway. Tighten all bolts used in Steps 13, 14 and 15. Head Cap Bolt Spring Washer Flat Washer Head Cap Bolt Spring Washer Flat Washer E E E E STEP 16 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers. For a 4 seat sectional, complete Steps 17 and 18. For a 5 seat sectional, follow instructions in 6800-58 carton, then complete Steps 19 and 20.
Assembly Instructions 4/7 4 Seat Sectional STEP 17 Attach left unit, middle unit, corner unit and right unit with Clips (J). (See Figure 4) Right Unit Left Unit Middle Unit J J J Figure 4 J Corner Unit J I G G J K G Toggle H F F Figure 5 F STEP 18 Turn unit to its upright position. Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit. (See Figure 5) Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Assembly Instructions 5/7 5 Seat Sectional STEP 19 Right Unit Attach left unit, middle units, corner unit and right unit with Clips (J). (See Figure 7) Middle Unit Left Unit Middle Unit Figure 7 G F K I G F H F G J J J J J J J J Corner Unit G Toggle F Figure 8 STEP 20 6800-CUS carton is also needed for this step. Turn unit to its upright position. Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit.
Assembly Instructions 6/7 6 Seat Sectional STEP 21 Right Unit Attach left unit, middle units, corner unit and right unit with Clips (J). (See Figure 10) Left Unit Middle Unit Middle Unit Figure 10 Middle Unit J J G G I K J G H F F F J J J J Corner Unit J G J J G Toggle F F Figure 11 STEP 22 Two 6800-CUS cartons are also needed for this step. Turn unit to its upright position. Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit.
Assembly Instructions 7/7 7 Seat Sectional Right Unit STEP 23 Attach left unit, middle units, corner unit and right unit with Clips (J). (See Figure 13) Middle Unit J J J J J J Middle Unit Left Unit Middle Unit Middle Unit J Figure 13 J G G F I G F F K H F G G J J J J Corner Unit G Toggle F F Figure 14 STEP 24 Three 6800-CUS cartons are also needed for this step. Turn unit to its upright position.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
6800-CUS3 Cushions IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Part List F. Seat Cushion 3 pcs. G. Back Cushion 3 pcs. Care Instructions Keep cushions free of natural debris. Tip and angle cushions after use. Store cushions inside when not in use.
6801-57 Seating IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Back 1 pc. B. Seat 1 pc. C. Side 1 pc. D. Frame 1 pcs. E. Foot 4 pcs. J. Clip 1 pc. Hardware List Hex Wrench 1 pc. Small Hex Wrench 1 pc. M6x35 Head Cap Bolt 22 pcs.
Assembly Instructions 2/7 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. Left Unit STEP 1 A Attach Seat (B) to Back (A) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/7 STEP 3 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2 and 3. Flat Washer Spring Washer Head Cap Bolt D Head Cap Bolt Spring Washer Flat Washer E E E E Figure 3 STEP 4 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 4/7 Right Unit A STEP 5 Attach Seat (B) to Back (A) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. B Flat Washer Spring Washer Head Cap Bolt STEP 6 Attach unit to Side (C) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 5/7 STEP 7 Attach Frame (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 5, 6 and 7. D Flat Washer Spring Washer Head Cap Bolt Head Cap Bolt Spring Washer Flat Washer E E E E STEP 8 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 6/7 For a loveseat, complete Steps 9 and 10. For a sofa, follow instructions in 6801-58 carton. Loveseat STEP 9 Attach left unit and right unit with Clips (J).
Assembly Instructions 7/7 Toggle Figure 5 G G Toggle F F STEP 10 Two 6801-CUS cartons are also needed for this step. Turn unit to its upright position. Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit. (See Figure 5) Place Back Cushions (G) into position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
6801-CUS Cushions IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Part List F. Seat Cushion 1 pc. G. Back Cushion 1 pc. Care Instructions Keep cushions free of natural debris. Tip and angle cushions after use. Store cushions inside when not in use.
6800-20 End Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Panel 2 pcs. D. Base 1 pc. C. Panel 2 pcs. E. Foot 4 pcs. Hardware List Hex Wrench 1 pc. (+1 extra) Small Hex Wrench 1 pc. M6x35 Head Cap Bolt 20 pcs.
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Attach Base (D) to Panel (B) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/5 Flat Washer Spring Washer Head Cap Bolt B STEP 3 Attach Panel (B) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Head Cap Bolt Spring Washer Flat Washer STEP 4 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway.
Assembly Instructions 4/5 Head Cap Bolt Spring Washer Flat Washer STEP 5 Attach Panel (C) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. C Tighten all bolts used in Steps 1, 2, 3, 4 and 5. Head Cap Bolt Spring Washer Flat Washer E E E E Figure 2 STEP 6 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 5/5 A STEP 7 Turn over unit to its upright position. Place Top (A) into position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.