Installation Guide

ManualsBrandsHOMESTYLES ManualsGarages & Outdoor StorageMaho 24 in. W x 15.75 in. D x 64 in. H French Grey Storage Cabinet

Part List

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

20 05664 0026

IMPORTANT

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Cabinet

Hardware List

Base

1 pc.

Stretcher

1 pc.

Door

1 pc.

Side Panel

1 pc.

Side Panel

1 pc.

Back Panel

1 pc.

Knob

1 pc.

Key

1 pc.

M8x32

Wood Screw

for Knob

1 pc. (+1 extra)

M7x60

Assembly Screw

12 pcs. (+1 extra)

M6x19

Wood Screw

for Door Hinge

9 pcs. (+1 extra)

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

Adjustable Pin

12 pcs. (+1 extra)

Top

1 pc.

Shelf

3 pcs.

Summary of content (6 pages)

PAGE 1
20 05664 0026 Cabinet IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Shelf 3 pcs. C. Base 1 pc. D. Stretcher 1 pc. E. Side Panel 1 pc. F. Side Panel 1 pc. G. Back Panel 1 pc. H. Door 1 pc. Hardware List Small Hex Wrench 1 pc.
PAGE 2
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. Assembly Screw E G D F C STEP 1 Attach Back Panel (G), Base (C) and Stretcher (D) to Side Panel (E) with Assembly Screws.
PAGE 3
Assembly Instructions 3/5 Adjustable Pin Knob Figure 1 B H B Wood Screw for Knob Figure 2 B Figure 3 STEP 3 Turn unit to its upright position. Insert Adjustable Pins into side panels at desired level. (See Figure 1) Place Shelves (B) into position. Attach Door (H) to unit with Wood Screws for Door Hinge. (See Figure 2) Figure 4 Attach Knob to Door (H) with Wood Screw for Knob. (See Figure 3) Turn Key counter clockwise to lock Door (H) and clockwise to unlock.
PAGE 4
Assembly Instructions 4/5 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 4 Anchor in wall Place unit at desired location. Bracket on wall Pre-drilled hole at top of unit Wall Screw Wood Screw 3/8” wall hole Drill a 3/8” hole in wall in-line with the pre-drilled hole at top of unit. Move unit. Insert Anchor into the wall hole and attach Bracket with Wall Screw.
PAGE 5
Assembly Instructions 5/5 IMPORTANT If magnetic door catches are too strong and door is difficult to open, magnetic power can be reduced and door made easier to open by doing the following: 1 Magnet Magnet location. 2 Magnet position. Magnet 3 4 Rotate Magnet until one Screw is all the way forward and other Screw is all the way back in catch slots. Loosen Screws only halfway. 5 6 Tighten Screws. New position.
PAGE 6
CARE INSTRUCTIONS Advisory Notes · · · · · · · Do not use power tools above 8 volts to assemble. Periodic structural checks of this furniture should be undertaken. Do not use if there are any doubts about its’ fitness for purpose. Exercise care so as to not trap fingers in any of the hinged parts of this furniture. Always use on firm level ground, ensuring that all legs remain in contact with the ground. Do not stand on a chair or sit or stand on any other item.