20 05520 0912 Storage Island IMPORTANT Part List G. Side Panel 1 pc. H. Side Panel 1 pc. I. Shelf 3 pcs. J. Drawer 1 pc. Refer to later page(s) of these instructions for drawer assembly. K. Drawer 3 pcs. For assembly see instructions in carton 20 05520 0911.
0 05520 0911 Storage Island IMPORTANT Part List A. Top 1 pc. B. Rail 2 pcs. C. Rail 3 pcs. D. Back Panel 1 pc. E. Bottom 1 pc. F. Plinth 2 pcs. Hardware List Hex Wrench 1 pc. Cam Lock 26 pcs. (+6 extra) Flat Washer 12 pcs. (+1 extra) Spring Washer 12 pcs. (+1 extra) M6x32 Head Cap Bolt 12 pcs. (+1 extra) Handle 4 pcs. Small Hex Wrench 1 pc. Cam Lock Screw 26 pcs. (+2 extra) Adjustable Pin 12 pcs. (+1 extra) M3.5x32 Wood Screw 4 pcs. (+1 extra) M4x16 Machine Screw 8 pcs.
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/8 STEP 2 Attach Back Panel (D) to Bottom (E) with Cam Locks. (See Figure 2) D Attach Plinths (F) to unit with Cam Locks. F E F Cam Lock Figure 2 Wood Screw Flat Washer Spring Washer STEP 3 Head Cap Bolt Attach unit form Step 2 to Side Panel (H) with Flat Washers, Spring Washers, Head Cap Bolts and Cam Locks, tightening bolts only halfway. (See Figure 3) B B C C Attach Rails (B) and (C) to unit with Cam Locks and Wood Screws.
Assembly Instructions 4/8 Wood Screw G STEP 4 Attach Side Panel (G) to unit with Cam Locks, Flat Washers, Spring Washers, Head Cap Bolts and Wood Screws, tightening bolts only halfway. Turn unit to it’s upright position. Cam Lock Flat Washer Spring Washer Head Cap Bolt Adjustable Pin STEP 5 I Insert Adjustable Pins into side panels at desired level. I Place Shelves (I) into position.
Assembly Instructions 5/8 Drawer (J) STEP 6 J4 Attach Drawer Sides (J3) and (J4) to Drawer Back (J2), then flip Locks. (See Figures 4 and 5) J3 J2 Lock STEP 7 Figure 4 Figure 5 Slide Drawer Bottom (J5) into groove. J1 Attach Drawer Front (J1) to unit, then flip Locks. J5 Lock Machine Screw STEP 8 Attach Handle with Machine Screw. Handle Part List J1. Drawer Front 1 pc. J2. Drawer Back 1 pc. J3. Drawer Side 1 pc. J4. Drawer Side 1 pc. J5. Drawer Bottom 1 pc.
Assembly Instructions 6/8 Drawer (K) STEP 9 K4 Attach Drawer Sides (K3) and (K4) to Drawer Back (K2), then flip Locks. K3 K2 Lock K1 STEP 10 K5 Slide Drawer Bottom (K5) into groove. Attach Drawer Front (K1) to unit, then flip Locks. Lock Machine Screw STEP 11 Attach Handle with Machine Screw. Handle Part List K1. Drawer Front 3 pcs. K2. Drawer Back 3 pcs. K3. Drawer Side 3 pcs. K4. Drawer Side 3 pcs. K5. Drawer Bottom 3 pcs.
Assembly Instructions 7/8 A Flat Washer Spring Washer Head Cap Bolt Cam Lock STEP 12 Attach Top (A) to unit with Cam Locks Flat Washer, Spring Washer and Head Cap Bolts, tightening bolts only halfway. STEP 13 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 6) Note: Unit must be level to work properly. Slide Drawers (J) and (K) into position.
Assembly Instructions 8/8 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 14 to install it. STEP 14 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is against a wall. Anchor in wall Bracket on wall Wall Screw 3/8” wall hole 3/16” hole in side panel of unit Wood Screw Place unit at desired location. Drill a 3/8” hole in wall in-line with 3/16” hole drilled in side panel. Tie end Move unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05520 0921 Storage Island IMPORTANT Part List A. Top 1 pc. For assembly see instructions in carton 20 05520 0923.
20 05520 0922 Storage Island IMPORTANT Part List D. Back Panel 1 pc. G. Side Panel 1 pc. H. Side Panel 1 pc. For assembly see instructions in carton 20 05520 0923.
20 05520 0923 Storage Island IMPORTANT Part List B. Rail 2 pcs. C. Rail 3 pcs. F. Plinth 2 pcs. E. Bottom 1 pc. J. Drawer 1 pc. I. Shelf 3 pcs. K. Drawer 3 pcs. Refer to later page(s) of these instructions for drawer assembly. Hardware List Hex Wrench 1 pc. Cam Lock 30 pcs. (+6 extra) Flat Washer 12 pcs. (+1 extra) Spring Washer 12 pcs. (+1 extra) M6x32 Head Cap Bolt 12 pcs. (+1 extra) Handle 4 pcs. Small Hex Wrench 1 pc. Cam Lock Screw 30 pcs. (+2 extra) Adjustable Pin 12 pcs.
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/8 STEP 2 D F Attach Back Panel (D) to Bottom (E) with Cam Locks. (See Figure 2) Attach Plinths (F) to unit with Cam Locks. E F Cam Lock Figure 2 Wood Screw Flat Washer Spring Washer STEP 3 B Head Cap Bolt Attach unit form Step 2 to Side Panel (H) with Flat Washers, Spring Washers, Head Cap Bolts and Cam Locks, tightening bolts only halfway. (See Figure 3) B C C Attach Rails (B) and (C) to unit with Cam Locks and Wood Screws.
Assembly Instructions 4/8 Wood Screw G STEP 4 Attach Side Panel (G) to unit with Cam Locks, Flat Washers, Spring Washers, Head Cap Bolts and Wood Screws, tightening bolts only halfway. Turn unit to it’s upright position. Cam Lock Flat Washer Spring Washer Head Cap Bolt Adjustable Pin STEP 5 I I I Insert Adjustable Pins into side panels at desired level. Place Shelves (I) into position.
Assembly Instructions 5/8 Drawer (J) STEP 6 J4 Attach Drawer Sides (J3) and (J4) to Drawer Back (J2), then flip Locks. (See Figures 4 and 5) J3 J2 Lock Figure 4 STEP 7 Figure 5 Slide Drawer Bottom (J5) into groove. J1 Attach Drawer Front (J1) to unit, then flip Locks. J5 Lock Machine Screw STEP 8 Attach Handle with Machine Screw. Handle Part List J1. Drawer Front 1 pc. J2. Drawer Back 1 pc. J3. Drawer Side 1 pc. J4. Drawer Side 1 pc. J5. Drawer Bottom 1 pc.
Assembly Instructions 6/8 Drawer (K) K4 K3 K2 STEP 9 Lock Attach Drawer Sides (K3) and (K4) to Drawer Back (K2), then flip Locks. STEP 10 K1 Slide Drawer Bottom (K5) into groove. Attach Drawer Front (K1) to unit, then flip Locks. K5 Lock Machine Screw STEP 11 Attach Handle with Machine Screw. Handle Part List K1. Drawer Front 3 pcs. K2. Drawer Back 3 pcs. K3. Drawer Side 3 pcs. K4. Drawer Side 3 pcs. K5. Drawer Bottom 3 pcs.
Assembly Instructions 7/8 A Flat Washer Spring Washer Head Cap Bolt Cam Lock STEP 12 Attach Top (A) to unit with Cam Locks Flat Washer, Spring Washer and Head Cap Bolts, tightening bolts only halfway. STEP 13 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 6) Note: Unit must be level to work properly. Slide Drawers (J) and (K) into position.
Assembly Instructions 8/8 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 14 to install it. STEP 14 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is against a wall. Anchor in wall Bracket on wall Wall Screw 3/8” wall hole 3/16” hole in side panel of unit Wood Screw Place unit at desired location. Drill a 3/8” hole in wall in-line with 3/16” hole drilled in side panel. Tie end Move unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05520 0931 Storage Island IMPORTANT Part List A. Top 1 pc. For assembly see instructions in carton 20 05520 0932.
20 05520 0932 Storage Island IMPORTANT Part List D. Back Panel 1 pc. E. Back Panel 1 pc. F. Middle Panel 1 pc. G. Side Panel 1 pc. H. Side Panel 1 pc. Hardware List Hex Wrench 1 pc. Cam Lock 45 pcs. (+6 extra) Flat Washer 14 pcs. (+1 extra) Spring Washer 14 pcs. (+1 extra) M6x32 Head Cap Bolt 14 pcs. (+1 extra) Handle 8 pcs. Small Hex Wrench 1 pc. Cam Lock Screw 45 pcs. (+2 extra) Adjustable Pin 24 pcs. (+1 extra) M3.5x32 Wood Screw 4 pcs. (+1 extra) M4x16 Machine Screw 16 pcs.
Assembly Instructions 2/9 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/9 Cam Lock STEP 2 E Attach Back Panels (D) and (E) to Middle Panel (F) with Cam Locks. (See Figure 2) F D Figure 2 Head Cap Bolt Spring Washer Flat Washer STEP 3 Attach Bottom (J) to unit with Flat Washers, Spring Washers, Head Cap Bolts and Cam Locks, tightening bolts only halfway.
Assembly Instructions 4/9 Cam Lock I I STEP 4 Attach Plinths (I) to unit with Cam Locks. B Flat Washer Spring Washer B Head Cap Bolt STEP 5 Attach Rails (C) to Side Panel (H) with Cam Locks. Attach unit from Step 4 to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. C C C Attach Rails (B) to unit with Wood Screws.
Assembly Instructions 5/9 Wood Screw STEP 6 G Attach Rails (C) to unit with Cam Locks. Attach Side Panel (G) to unit with Cam Locks Flat Washers, Spring Washers, Head Cap Bolts and Wood Screws, tightening bolts only halfway. C Turn unit to it’s upright position. C C Flat Washer Spring Washer Head Cap Bolt Cam Lock A Flat Washer Spring Washer Head Cap Bolt Cam Lock STEP 7 Attach Top (A) to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
Assembly Instructions 6/9 Drawer (L) STEP 8 L4 Attach Drawer Sides (L3) and (L4) to Drawer Back (L2), then flip Locks. (See Figures 4 and 5) L3 L2 Lock STEP 9 Figure 4 Figure 5 Slide Drawer Bottom (L5) into groove. L1 Attach Drawer Front (L1) to unit, then flip Locks. L5 Lock Machine Screw STEP 10 Attach Handle with Machine Screw. Handle Part List L1. Drawer Front 2 pcs. L2. Drawer Back 2 pcs. L3. Drawer Side 2 pcs. L4. Drawer Side 2 pcs. L5. Drawer Bottom 2 pcs.
Assembly Instructions 7/9 Drawer (M) M4 STEP 11 M3 M2 Attach Drawer Sides (M3) and (M4) to Drawer Back (M2), then flip Locks. Lock STEP 12 M1 Slide Drawer Bottom (M5) into groove. M5 Attach Drawer Front (M1) to unit, then flip Locks. Lock Machine Screw STEP 13 Attach Handle with Machine Screw. Handle Part List M1. Drawer Front 6 pcs. M2. Drawer Back 6 pcs. M3. Drawer Side 6 pcs. M4. Drawer Side 6 pcs. M5. Drawer Bottom 6 pcs.
Assembly Instructions 8/9 L M L M M M M M STEP 14 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 6) Note: Unit must be level to work properly. Slide Drawers (L) and (M) into position. Figure 6 Adjustable Pin K K K STEP 15 K K K Insert Adjustable Pins into side panels and middle panel at desired level. Place Shelves (K) into position.
Assembly Instructions 9/9 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 16 to install it. STEP 16 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is against a wall. Anchor in wall Bracket on wall Wall Screw 3/8” wall hole 3/16” hole in side panel of unit Wood Screw Place unit at desired location. Drill a 3/8” hole in wall in-line with 3/16” hole drilled in side panel. Tie end Move unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05520 0933 Storage Island IMPORTANT Part List B. Rail 2 pcs. K. Shelf 6 pcs. C. Rail 6 pcs. L. Drawer 2 pcs. I Plinth 2 pcs. M. Drawer 6 pcs. Refer to later page(s) of these instructions for drawer assembly. J. Bottom 1 pc. For assembly see instructions in carton 20 05520 0932.
20 05520 0761 Closet Wall Shelf Unit IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List B. Shelf 3 pcs. A. Top 1 pc. C. Front Rail 1 pc. D. Side Panel 1 pc. E. Side Panel 1 pc. F. Back Panel 1 pc. For assembly see instructions in carton 20 05520 0762.
20 05520 0762 Closet Wall Shelf Unit IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List H. Front Rail 1 pc. G. Top 1 pc. J. Plinth 1 pc. N. Back Panel 1 pc. L. Side Panel 1 pc. B. Shelf 3 pcs. M. Side Panel 1 pc. Hardware List Plug 4 pcs.
Assembly Instructions 2/7 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/7 STEP 3 L Attach unit to Side Panel (M) with Cam Locks, then flip Locks. (See Figure 4) Attach Back Panel (N) to unit, then flip Locks. Attach Front Rails (H) to unit with Wood Screw (long). N Attach Side Panel (L) to unit with Cam Locks and Wood Screw (long), then flip Locks. H M Cam Lock Wood Screw (long) STEP 4 Figure 4 Attach Levelers to bottom of unit with Wood Screws for Levelers into pre-drilled holes.
Assembly Instructions 4/7 Cam Lock C STEP 6 Attach Back Panel (F) to Side Panel (D), then flip Locks. Attach Front Rail (C) to unit with Cam Lock. Attach Side Panel (E) to unit with Cam Lock, then flip Locks. D F E Lock A STEP 7 Attach Top (A) to unit, then flip Locks.
Assembly Instructions 5/7 STEP 8 Place top unit onto base unit, then flip Locks. B Adjustable Pin Lock B B B Adjustable Pin B B Plug STEP 9 Place unit at desired location. Note: If assembling multiple Closet Wall Units together, place all units at desired location. Figure 6 Level unit(s) by adjusting the adjustable levelers on bottom of unit(s). (See Figure 6) Note: Unit(s) must be level to proceed. Cover all holes with Plugs. (See Figure 7) Insert Adjustable Pins into side panels at desired level.
Assembly Instructions 6/7 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 10 Place unit at desired location. Anchor in wall Drill a 3/8” hole in wall in-line with the pre-drilled hole at top of unit. Bracket on wall Pre-drilled hole at top of unit Wall Screw 3/8” wall hole Wood Screw Move unit. Insert Anchor into the wall hole and attach Bracket with Wall Screw.
Assembly Instructions 7/7 Wood Screw for Bracket Bracket Figure 9 STEP 11 Note: If assembling multiple Closet Wall Units together, complete Step 11. Attach tops of units together with Brackets and Wood Screws for Brackets into pre-drilled holes. (See Figure 9) Return to and complete Step 10.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05520 0771 Closet Wall Hanging Unit IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List B. Front Rail 1 pc. A. Top 1 pc. C. Side Panel 1 pc. D. Side Panel 1 pc. E. Back Panel 1 pc. F. Back Panel 1 pc.
20 05520 0772 Closet Wall Hanging Unit IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List L. Rod 2 pcs. G. Top 1 pc. M. Front Rail 1 pc. N. Plinth 1 pc. H. Side Panel 1 pc. I. Side Panel 1 pc. J. Back Panel 1 pc. Hardware List Plug 4 pcs.
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/8 Lock O N STEP 2 Attach Plinth (N) to Bottom (O), then flip Locks. (See Figures 3 and 4) Figure 3 Figure 4 Wood Screw (long) Cam Lock STEP 3 H Attach unit to Side Panel (I) with Cam Locks, then flip Locks. (See Figure 5) J Attach Back Panels (K) and (J) to unit, then flip Locks. Attach Front Rail (M) to unit with Wood Screw (long). Attach Side Panel (H) to unit with Cam Locks and Wood Screw (long), then flip Locks.
Assembly Instructions 4/8 STEP 4 Attach Levelers to bottom of unit with Wood Screws for Levelers into pre-drilled holes. (See Figure 6) Figure 6 G Wood Screw for Leveler Leveler Lock Wood Screw (long) STEP 5 Attach Top (G) to unit with Wood Screws (long), then flip Locks.
Assembly Instructions 5/8 Cam Lock B STEP 6 Attach Back Panel (E) to Side Panel (C), then flip Locks. Attach Back Panel (F) to Side Panel (D), then flip Locks. C E F Attach Front Rail (B) to unit with Cam Lock. D Attach unit to unit with Cam Lock. Lock A STEP 7 Attach Top (A) to unit, then flip Locks.
Assembly Instructions 6/8 STEP 8 L Place top unit onto base unit, then flip Locks. Lock L Plug STEP 9 Place unit at desired location. Figure 7 Note: If assembling multiple Closet Wall Units together, place all units at desired location. Level unit(s) by adjusting the adjustable levelers on bottom of unit(s). (See Figure 7) Note: Unit(s) must be level to proceed. Cover all holes with Plugs. (See Figure 8) Figure 8 Figure 9 Place Rods (L) into position.
Assembly Instructions 7/8 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 10 Place unit at desired location. Anchor in wall Drill a 3/8” hole in wall in-line with the pre-drilled hole at top of unit. Bracket on wall Pre-drilled hole at top of unit Wall Screw 3/8” wall hole Wood Screw Move unit. Insert Anchor into the wall hole and attach Bracket with Wall Screw.
Assembly Instructions 8/8 Wood Screw for Bracket Bracket Figure 11 STEP 11 Note: If assembling multiple Closet Wall Units together, complete Step 11. Attach tops of units together with Brackets and Wood Screws for Brackets into pre-drilled holes. (See Figure 11) Return to and complete Step 10.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05520 0751 Closet Wall Drawer Unit IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List B. Shelf 3 pcs. A. Top 1 pc. C. Front Rail 1 pc. D. Side Panel 1 pc. E. Side Panel 1 pc. F. Back Panel 1 pc. For assembly see instructions in carton 20 05520 0752.
20 05520 0752 Closet Wall Drawer Unit IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List H. Front Rail 1 pc. G. Top 1 pc. L. Side Panel 1 pc. Plug 4 pcs. (+1 extra) Leveler 4 pcs. Hex Wrench 1 pc. J. Plinth 1 pc. N. Back Panel 1 pc. K. Bottom 1 pc. O.
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/8 STEP 3 L Attach unit to Side Panel (M) with Cam Locks, then flip Locks. (See Figure 4) Attach Back Panel (N) to unit, then flip Locks. Attach Front Rails (H) and (I) to unit with Cam Locks and Wood Screw (long). Attach Side Panel (L) to unit with Cam Locks and Wood Screw (long), then flip Locks. I N I H Cam Lock M Wood Screw (long) STEP 4 Figure 4 Attach Levelers to bottom of unit with Wood Screws for Levelers into pre-drilled holes.
Assembly Instructions 4/8 Cam Lock C STEP 6 Attach Back Panel (F) to Side Panel (D), then flip Locks. Attach Front Rail (C) to unit with Cam Lock. Attach Side Panel (E) to unit with Cam Lock, then flip Locks. D F E Lock A STEP 7 Attach Top (A) to unit, then flip Locks.
Assembly Instructions 5/8 Drawer (O) O4 STEP 8 O2 O3 Attach Drawer Sides (O3) and (O4) to Drawer Back (O2), then flip Locks. (See Figures 6 and 7) Lock Figure 6 STEP 9 Figure 7 Slide Drawer Bottom (O5) into grooves in Drawer Sides (O3) and (O4) until it meets Drawer Back (O2). Attach Drawer Front (O1) to unit, then flip Locks. Machine Screw O1 O4 O3 O2 O5 Lock STEP 10 Attach Handle with Machine Screws. Handle Part List O1. Drawer Front 3 pcs. O2. Drawer Back 3 pcs. O3. Drawer Side 3 pcs.
Assembly Instructions 6/8 STEP 11 Place top unit onto base unit, then flip Locks. B Lock Adjustable Pin B B O O O Plug STEP 12 Place unit at desired location. Note: If assembling multiple Closet Wall Units together, place all units at desired location. Figure 8 Level unit(s) by adjusting the adjustable levelers on bottom of unit(s). (See Figure 8) Note: Unit(s) must be level to proceed. Cover all holes with Plugs. (See Figure 9) Insert Adjustable Pins into side panels at desired level.
Assembly Instructions 7/8 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 13 Place unit at desired location. Anchor in wall Drill a 3/8” hole in wall in-line with the pre-drilled hole at top of unit. Bracket on wall Pre-drilled hole at top of unit Wall Screw 3/8” wall hole Wood Screw Move unit. Insert Anchor into the wall hole and attach Bracket with Wall Screw.
Assembly Instructions 8/8 Wood Screw for Bracket Bracket Figure 11 STEP 14 Note: If assembling multiple Closet Wall Units together, complete Step 14. Attach tops of units together with Brackets and Wood Screws for Brackets into pre-drilled holes. (See Figure 11) Return to and complete Step 13.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.