Bedienungsanleitung User manual Wechselrahmen – schmal S. 2 Clip-on Frame – small p.
Lieferumfang Anzahl Bezeichnung 1 Homematic IP Wechselrahmen – schmal 2 Doppelseitige Klebestreifen 2 Schrauben 3,0 x 30 mm 2 Dübel 5 mm 1 Bedienungsanleitung Dokumentation © 2017 eQ-3 AG, Deutschland Alle Rechte vorbehalten. Ohne schriftliche Zustimmung des Herausgebers darf diese Anleitung auch nicht auszugsweise in irgendeiner Form reproduziert werden oder unter Verwendung elektronischer, mechanischer oder chemischer Verfahren vervielfältigt oder verarbeitet werden.
1 A B
2 C 3
4 5
Inhaltsverzeichnis 1 2 3 4 5 Hinweise zur Anleitung.................................................... 7 Gefahrenhinweise............................................................. 7 Funktion und Geräteübersicht.......................................9 Allgemeine Informationen............................................10 Montage............................................................................10 5.1 5.2 6 7 6 Klebestreifenmontage.........................................................
Hinweise zur Anleitung 1 Hinweise zur Anleitung Lesen Sie diese Anleitung sorgfältig, bevor Sie den Homematic IP Wechselrahmen montieren. Bewahren Sie die Anleitung zum späteren Nachschlagen auf! Wenn Sie den Rahmen anderen Personen zur Nutzung überlassen, übergeben Sie auch diese Bedienungsanleitung. Benutzte Symbole: Achtung! Hier wird auf eine Gefahr hingewiesen. Hinweis.
Gefahrenhinweise Aus Sicherheits- und Zulassungsgründen (CE) ist das eigenmächtige Umbauen und/oder Verändern des Rahmens nicht gestattet. Verwenden Sie den Rahmen nur in Innenräumen und setzen Sie ihn keinem Einfluss von Feuchtigkeit, Vibrationen, ständiger Sonnen- oder anderer Wärmeeinstrahlung, übermäßiger Kälte und keinen mechanischen Belastungen aus. Der Rahmen ist kein Spielzeug, erlauben Sie Kindern nicht damit zu spielen.
Funktion und Geräteübersicht 3 Funktion und Geräteübersicht Der Homematic IP Wechselrahmen – schmal kann universell für die Montage von batterieversorgten Geräten im 55er-Format (z. B. Homematic IP Wandthermostat oder Homematic IP Wandtaster – 2-fach) verwendet werden. Die Geräte können einfach und ohne Werkzeug in den Wechselrahmen eingesetzt werden.
Allgemeine Informationen 4 Allgemeine Informationen Dieses Gerät ist Teil des Homematic IP Systems und kann mit allen Homematic IP Geräten im 55er-Format kombiniert werden (s. „5 Montage“ auf Seite 10). Gleichermaßen können auch batteriebetriebene Geräte im 55er-Format anderer Systeme (wie z. B. HomeMatic, MAX! oder FS20) in den Wechselrahmen eingesetzt werden. Alle technischen Dokumente und Updates finden Sie stets aktuell unter www.eQ-3.de. Die vollständige Konformitätserklärung finden Sie unter www.
Montage 5.1 Klebestreifenmontage Um den Wechselrahmen mit den Klebestreifen zu montieren, gehen Sie wie folgt vor: • Wählen Sie einen beliebigen Montageort aus. Achten Sie darauf, dass der Montageuntergrund glatt, eben, unbeschädigt, sauber, fett- sowie lösungsmittelfrei und nicht zu kühl ist, damit der Klebestreifen langfristig haften kann. • • • • Befestigen Sie die Klebestreifen (C) auf der Rückseite des Wechselrahmens in den dafür vorgesehenen Markierungen (s. Abbildung 2).
Montage 5.2 Schraubmontage Um den Wechselrahmen mithilfe der Schrauben zu montieren, gehen Sie wie folgt vor: • Wählen Sie einen geeigneten Montageort aus. Stellen Sie sicher, dass an der ausgewählten Position in der Wand keine Leitungen verlaufen! • • • Halten Sie den Wechselrahmen an die gewünschte Montageposition. Zeichnen Sie zwei Bohrlöcher (B) anhand des Wechselrahmens in einem Abstand von 30 mm mit einem Stift an der Wand an (s. Abbildung 4). Bohren Sie die vorgezeichneten Löcher.
Wartung und Reinigung Wie Sie das eingesetzte Gerät ins Homematic IP System integrieren können, entnehmen Sie bitte der jeweiligen Bedienungsanleitung. 6 Wartung und Reinigung Das Produkt ist für Sie wartungsfrei. Überlassen Sie eine Wartung oder Reparatur einer Fachkraft. Reinigen Sie das Produkt mit einem weichen, sauberen, trockenen und fusselfreien Tuch. Für die Entfernung von stärkeren Verschmutzungen kann das Tuch leicht mit lauwarmem Wasser angefeuchtet werden.
Entsorgungshinweis Gerät nicht im Hausmüll entsorgen! Elektronische Geräte sind entsprechend der Richtlinie über Elektro- und Elektronik-Altgeräte über die örtlichen Sammelstellen für Elektronik-Altgeräte zu entsorgen. Konformitätshinweis Das CE-Zeichen ist ein Freiverkehrszeichen, das sich ausschließlich an die Behörden wendet und keine Zusicherung von Eigenschaften beinhaltet. Bei technischen Fragen zum Gerät, wenden Sie sich bitte an Ihren Fachhändler.
Package contents Quantity Description 1 Homematic IP Clip-on Frame – small 2 Double-sided adhesive strips 2 Screws 3.0 x 30 mm 2 Plugs 5 mm 1 User manual Documentation © 2017 eQ-3 AG, Germany All rights reserved. Translation from the original version in German. This manual may not be reproduced in any format, either in whole or in part, nor may it be duplicated or edited by electronic, mechanical or chemical means, without the written consent of the publisher.
Table of contents 1 2 3 4 5 Information about this manual.................................... 17 Hazard information......................................................... 17 Function and device overview.....................................19 General information...................................................... 20 Mounting.......................................................................... 20 5.1 5.2 6 7 16 Adhesive strip mounting.....................................................
Information about this manual 1 Information about this manual Please read this manual carefully before beginning installation of your Homematic IP Clip-on Frame. Keep the manual so you can refer to it at a later date if you need to. If you hand over the frame to other persons for use, please hand over the operating manual as well. Symbols used: Attention! This indicates a hazard. Please note: This section contains important additional information.
Hazard information For safety and licensing reasons (CE), unauthorized change and/or modification of the frame is not permitted. The frame may only be operated indoors and must be protected from the effects of moisture, vibrations, solar or other methods of heat radiation, cold and mechanical loads. The frame is not a toy; do not allow children to play with it. Do not leave packaging material lying around, plastic films/bags, pieces of polystyrene etc., can be dangerous in the hands of a child.
Function and device overview 3 Function and device overview The Homematic IP Clip-on Frame – small is suitable for universal installation of battery operated devices with the dimensions of 55 x 55 mm (e.g. Homematic IP Wall Thermostat or Homematic IP Wall-mount Remote Control – 2 buttons). The devices can be put into the clipon frame easily and without any tools. The clip-on frame is mounted very easily using the supplied screws or adhesive strips.
General information 4 General information This device is a component of the Homematic IP smart home system and can be combined with all devices with the dimensions of 55 x 55 mm (see sec. “6 Mounting” on page 20). Also battery operated devices with the dimensions of 55 x 55 mm of other systems (e.g. Homematic, MAX!, etc.) can be used with the clip-on frame. All current technical documents and updates are provided at www.eQ-3.com. You can find the full declaration of conformity at www.homematic-ip.com.
Mounting 5.1 Adhesive strip mounting For mounting the clip-on frame using the adhesive strips, please proceed as follows: • Choose a site for installation. Make sure that the mounting surface is smooth, solid, non-disturbed, free of dust, grease and solvents and not too cold to ensure long-time adherence. • • • • Fix the adhesive strips (C) on the back side of the clip-on frame in the provided area (see fig. 2). Remove the protective film from the adhesive strips.
Mounting 5.2 Screw mounting For mounting the clip-on frame using screws, please proceed as follows: • Choose a site for installation. Make sure that no electricity or similar lines run in the wall at this location! • • • Position the clip-on frame on the desired site on the wall. Use a pen to mark the positions of the two bore holes (B) according to the clip-on frame with a distance of 30 mm on the wall (see fig. 4). Now drill the bore holes.
Maintenance and cleaning Please refer to the operating manual of the inserted device for further information on integration into the Homematic IP system. 6 Maintenance and cleaning The product does not require you to carry out any maintenance. Enlist the help of an expert to carry out any maintenance or repairs. Clean the product using a soft, lint-free cloth that is clean and dry. You may dampen the cloth a little with lukewarm water in order to remove more stubborn marks.
Technical specifications Instructions for disposal Do not dispose of the device with regular domestic waste! Electronic equipment must be disposed of at local collection points for waste electronic equipment in compliance with the Waste Electrical and Electronic Equipment Directive. Information about conformity The CE sign is a free trading sign addressed exclusively to the authorities and does not include any warranty of any properties. For technical support, please contact your retailer.
Kostenloser Download der Homematic IP App! Free download of the Homematic IP app! Bevollmächtigter des Herstellers: Manufacturer’s authorised representative: eQ-3 AG Maiburger Straße 29 26789 Leer / GERMANY www.eQ-3.