Home NetWerks SIMPLE SOLUTIONS FOR A SMARTER HOME VENTILATING BATH FAN WITH BLUETOOTH® SPEAKER AND LED LIGHT MODEL #7130-18-BT Español p. 16 The BLUETOOTH® word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of the said mark by Homewerks Worldwide is under license. Other trademark and trade names are those of their respective owners. Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757, 8 a.m.
TABLE OF CONTENTS Product Specifications.........................................................................................................................2 Package Contents...............................................................................................................................3 Safety Information...............................................................................................................................4 Preparation..............................................
PACKAGE CONTENTS A B PART A DESCRIPTION Fan housing Grille with speaker and LED light B QUANTITY 1 1 HARDWARE CONTENTS (not shown actual size) AA Long Wood Screw Qty. 4 www.homewerksww.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. 1. Always disconnect the power supply prior to servicing the fan, motor or junction box. 2. Installation work must be carried out by a qualified person(s) in accordance to all local and safety codes including the rules for fire-rated construction. 3.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Tools Required for Assembly (not included): Hammer, Drill Bits, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Screwdriver, Utility Knife Helpful Tools (not included): Electric Drill, Wood Screws WARNING: Turn off electricity at breaker box before beginning installation.
NEW CONSTRUCTION ASSEMBLY INSTRUCTIONS NEW CONSTRUCTION – ATTACHING TO THE JOIST BEFORE INSTALLATION Turn off power source. Review all safety precautions. 1 2. Before mounting the fan housing to the joist, remove the plastic duct connector for easier access to the mounting hole on the fan housing. 2 1 2 1. Place the fan housing next to a ceiling joist or wall stud. The fan housing should be level and perpendicular to the joist or stud. Allow for thickness of ceiling board used in your application.
NEW CONSTRUCTION ASSEMBLY INSTRUCTIONS 4. Replace duct connector by hooking the connector on one side of the metal flange opening on the fan housing and then pressing down on the other side to snap the connector into place. Ensure that all four metal flanges on the fan housing are inside the plastic duct connector when it is replaced. 4 5. Pull the house wires through the wire box cover hole.
BLUETOOTH® SPEAKER FAN GRILLE INSTALLATION 2. Attach grille by pinching mounting springs and insert into narrow rectangular slots in the fan housing. 2 Turn on power source. PAIRING YOUR BLUETOOTH® DEVICE TO THE SPEAKER 1. Turn ON the bath fan if using one switch, or turn on the LIGHT if using two switches. 2. To play your personal music files, you need a wireless BLUETOOTH® device. 3. Set your device to a midrange volume before connecting to the speaker. 4.
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS 2. Measure the opening to ensure it is large enough to accommodate the new fan housing (A) (7-1/2 in. x 7-1/4 in.). 2 3. If this fan is not replacing an old fan, be sure to cut a 7-1/2 in. x 7-1/4 in. opening for the fan housing (A). 3 9.4in" . 7-1/4 . "in 9/2.4 7-1 4 5. Before mounting the fan housing to the joist, remove the plastic duct connector for easier access to the mounting hole on the fan housing. 5 1 2 4.
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS 6. Mount fan housing to the joist or stud using long wood screws (AA) where indicated by arrows outside fan housing. 6 Hardware Used AA Long wood screws x2 7. Replace duct connector by hooking the connector on one side of the metal flange opening on the fan housing and then pressing down on the other side to snap the connector into place. Ensure that all four metal flanges on the fan housing are inside the plastic duct connector when it is replaced. 7 8.
BLUETOOTH® SPEAKER FAN GRILLE INSTALLATION Housing must be installed flush with ceiling board or the grille mounting spring will not be long enough to insert into the slots inside the fan housing. 1. Join the connectors for the BLUETOOTH® 1 speaker and power adapter. 2. Attach grille by pinching mounting springs and insert into narrow rectangular slots in the fan housing. 2 Turn on power source. EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS – ATTIC SPACE NOT ACCESSIBLE 1. Remove existing fan. 1 2.
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS – ATTIC SPACE NOT ACCESSIBLE 3. If this fan is not replacing an old fan, be sure to cut a 7-1/2 in. x 7-1/4 in. opening for the fan housing (A). 3 4. Remove grille mounting bracket by unscrewing two screws on each bracket. NOTE: Save screws for re-installation of fan motor and grille mounting brackets. 4 5. With screw removed slide the brackets to the left and then remove the housing. Remove the three prong fan plug from the housing.
EXISTING CONSTRUCTION ASSEMBLY INSTRUCTIONS – ATTIC SPACE NOT ACCESSIBLE 7. I nstall a circular 4 in. duct (not included) and secure it with duct tape or clamps (neither included). 7 Finish ceiling work. Ceiling hole should be aligned with edge of the fan housing. 8. With the wiring and duct connected insert the fan housing into the ceiling hole. Mount the housing to the joist with three wood screws through the holes in the side of the fan housing.
BLUETOOTH® SPEAKER FAN GRILLE INSTALLATION 2. Attach grille by pinching mounting springs and insert into narrow rectangular slots in the fan housing. 2 Turn on power source. PAIRING YOUR BLUETOOTH® DEVICE TO THE SPEAKER 1. Turn ON the bath fan if using one switch, or turn on the LIGHT if using two switches. 2. To play your personal music files, you need a wireless BLUETOOTH® device. 3. Set your device to a midrange volume before connecting to the speaker. 4.
TROUBLESHOOTING PROBLEM The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION CFM too great Be sure the CFM rating on the fan matches the size of your room. Damper not working properly or damaged Check damper to ensure it is opening and closing properly. If the damper has become damaged, please call Customer Service. Bend in duct too close to fan discharge Be sure you do not have any sharp bends in duct closer than 18 in. to the fan discharge.
VENTILADOR DE VENTILACIÓN CON BLUETOOTH®ALTAVOZ Y LUZ LED Home NetWerks SIMPLE SOLUTIONS FOR A SMARTER HOME MODELO #7130-18-BT Número de patente de EE.UU. 9,398,357 La marca BLUETOOTH® y sus logotipos son marcas comerciales registradas propiedad de Bluetooth SIG, Inc. y cualquier uso de dicha marca por Homewerks Worldwide es bajo licencia. Otros nombres de marcas y el comercio son de sus respectivos propietarios.
TABLA DE CONTENIDO Especificaciones del producto...........................................................................................................17 Contenido del paquete......................................................................................................................18 Información de seguridad .................................................................................................................19 Preparación ...........................................................
CONTENIDO DEL PAQUETE A B PIEZA A DESCRIPCIÓN Carcasa del ventilador Parrilla con altavoz y luz LED B CANTIDAD 1 1 ADITAMENTOS (no es el tamaño real) AA Tornillo de madera largo Cantidad 4 18 www.homewerksww.
INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. 1. Desconecte siempre el suministro de electricidad antes de realizar tareas de mantenimiento en el ventilador, el motor o la caja de unión. 2. Se recomienda instalación profesional. El trabajo de instalación debe ser realizada por una persona cualificada (s) de acuerdo con todos los códigos locales y de seguridad, incluyendo las normas de construcción resistente al fuego. 3.
PREPARACIÓN Antes de comenzar el montaje del producto, asegúrese de que todas las piezas estén presentes. Compare las piezas con la lista de contenido del paquete y la lista de contenido del hardware. Si falta alguna pieza o está dañada, no intente montar el producto.
INSTRUCCIONES DE ENSAMBLAJE NUEVA CONSTRUCCIÓN - COLOCACIÓN DE LA VIGA ANTES DE LA INSTALACIÓN Apague la fuente de poder. Revisar toda la seguridad precauciones. Coloque la carcasa del ventilador junto a una viga del techo o un perno de pared. La carcasa del ventilador debe estar nivelada y perpendicular a la viga o perno. Permitir el espesor de la tabla de techo utilizado en su aplicación. NO montar enrasado a la viga.
INSTRUCCIONES DE ENSAMBLAJE 4. Vuelva a colocar el conector del conducto enganchando el 4 5. Tire de los cables de la casa a través del orificio de la 3 conector en un lado de la abertura de brida metálica en la carcasa del ventilador y presionando hacia abajo en el otro lado para encajar el conector en su lugar. Asegúrese de que las cuatro bridas metálicas de la carcasa del ventilador están dentro del conector del conducto de plástico cuando se sustituye. tapa de la caja de alambre.
INSTALACIÓN DE LA PARRILLA DEL VENTILADOR DE BLUETOOTH® 2. Conecte la rejilla presionando los resortes de montaje e inserte en ranuras rectangulares estrechas en la carcasa del ventilador. 2 Encienda la fuente de alimentación. EMPAREJANDO SU DISPOSITIVO BLUETOOTH® AL ALTAVOZ 1. Encienda el ventilador de baño si usa un interruptor, o encienda la LUZ si usa dos interruptores. 2. Para reproducir sus archivos de música personales, necesita un dispositivo inalámbrico BLUETOOTH®. 3.
INSTRUCCIONES DE MONTAJE DE LA CONSTRUCCIÓN EXISTENTE 2. Mida la abertura para asegurar que es lo suficientemente 2 3. Si este ventilador no está reemplazando un ventilador 3 grande como para acomodar la nueva carcasa del ventilador (A) (7-1 / 2 pulgadas x 7-1 / 4 pulgadas). viejo, asegúrese de para cortar una abertura de 7-1 / 2 pulg. X 7-1 / 4 pulg. ventilador (A). 7-1/4 . 9p.4u"lg lg. "u 29.p4 / 7-1 4 5.
INSTRUCCIONES DE MONTAJE DE LA CONSTRUCCIÓN EXISTENTE 6. Monte la carcasa del ventilador a la viga o al perno usando tornillos de madera largos (AA) donde se indican mediante flechas fuera de la carcasa del ventilador. 6 Aditamentos utilizados AA Tornillo de madera largo x2 7. Vuelva a colocar el conector del conducto enganchando el 7 8.
INSTALACIÓN DE LA PARRILLA DEL VENTILADOR DE BLUETOOTH® La carcasa debe instalarse al ras con la placa de techo o el muelle de montaje de la rejilla no será lo suficientemente largo para insertar en las ranuras dentro de la carcasa del ventilador. 1. Una los conectores para el altavoz y el adaptador de cor1 riente BLUETOOTH®. 2. Conecte la rejilla presionando los resortes de montaje e inserte en ranuras rectangulares estrechas en la carcasa del ventilador. 2 Encienda la fuente de alimentación.
INSTRUCCIONES DE MONTAJE DE CONSTRUCCIÓN EXISTENTES – ESPACIO DEL ÁTICO NO ACCESIBLE Si este ventilador no está reemplazando un ventilador viejo, asegúrese de para cortar una abertura de 7-1 / 2 pulg. X 7-1 / 4 pulg.ventilador (A). 3 Retire el soporte de montaje de la parrilla desatornillando dos tornillos en cada soporte. 4 7-1/4 lg. p4"u /29. 7-1 NOTA: Guarde los tornillos para volver a instalar el ventilador soportes de montaje del motor y de la parrilla.
INSTRUCCIONES DE MONTAJE DE CONSTRUCCIÓN EXISTENTES – ESPACIO DEL ÁTICO NO ACCESIBLE Tire de los cables de la casa a través del orificio de la tapa de la caja de alambre. Utilizando un conector rápido, asegure el cableado de la casa de 120 V AC desde el interruptor de pared al ventilador como se muestra en el diagrama de cableado en la página 5. 14 AWB es el conductor más pequeño que se debe usar para el cableado del circuito derivado. Consulte los diagramas de cableado para obtener detalles en la página 5.
INSTALACIÓN DE LA PARRILLA DEL VENTILADOR DE BLUETOOTH® La carcasa debe instalarse al ras con la placa de techo o el muelle de montaje de la rejilla no será lo suficientemente largo para insertar en las ranuras dentro de la carcasa del ventilador. 1. Una los conectores para el altavoz y el adaptador de cor1 riente BLUETOOTH®. 2. Conecte la rejilla presionando los resortes de montaje e inserte en ranuras rectangulares estrechas en la carcasa del ventilador. 2 Encienda la fuente de alimentación.
CUIDADO Y MANTENIMIENTO Consulte la información de seguridad antes de proceder. El mantenimiento de rutina se debe hacer por lo menos una vez al año. • Nunca utilice solventes, diluyentes o productos químicos agresivos para limpiar el ventilador. • No permita que el agua entre en el motor. • No sumerja las piezas de metal en el agua. • No sumerja las piezas de resina en el agua por encima de 140 grados Fahrenheit.