Item# Model# FP21525 USE AND CARE GUIDE Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this fire pit. We strive to continually create quality products designed to enhance your home.
Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Pre-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Leakage Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operation . . . . . . . . . . . . . . . . . . .
Safety Information (continued) WARNING Read and follow all the instructions and warnings in this Owner’s Manual thoroughly before installing, operating, or servicing this fire pit. lmproper installation, use, maintenance, adjustment or storage can cause fire or explosion, resulting in serious injury or property damage. Prepare for use: Keep away from combustible/flammable items Do not put any other fireplace cover or anything flammable on or beneath the fire pit.
Safety Information (continued) Observe the flame color and the flame height in the fire pit after being lit: 1.) The flame color should be yellow. 2.) The flame height burns at 2 - 10 inches high. THIS PRODUCT USES PROPANE ONLY Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall) with a capacity of 9 kg/19.84 lbs. Max gas supply 28 cm/11 in. w.c.(2.74kpa). Only cylinders marked “propane” may be used.
Pre-Assembly Before beginning assembly of the fire pit, make sure all the parts are present. Compare the parts with the package contents list. If any part is missing or damaged, do not attempt to assemble the fire pit. NOTE: You must follow all the steps to properly assemble the fire pit. Make sure the gas valve is turned OFF before assembling. Do not attempt to assemble without the proper tools.
Assembly 1 Connecting the Propane Tank WARNING This fire pit requires air flow under the unit. Do not place on an uneven surface or on grass, turf, or carpet. Make sure the control knob (J) is turned to “OFF”. Turn door knob (N), and remove door (C). Place the propane tank (not included) in the metal stand inside the body (B) and make sure the propane tank sits on the metal stand completely. Turn the wing screw on the outer part of metal stand clockwise to secure the propane tank tightly.
Assembly (continued) a b Turn the cylinder valve on the top of tank clockwise to close off the gas supply. See Figure a. Screw the regulator coupling clockwise by hand only. Make sure it is fastened. See Figure b. Replace the door (C) onto the body (B) and turn the door knob (N) to secure. 2 Installing the Battery K G To install the battery (G), unscrew the rubber cap of the electric igniter (K) and place the battery (G) into the battery case.
Assembly (continued) 3 Installing the Fire Glass a b E WARNING c Keep the fire glass (F) and other objects off of the gas screen (E). Holes in the screen must be E D exposed in order to allow gas to escape. A blocked screen can cause gas to build inside the fire pit and ultimately cause an explosion and risk of serious injury. Note that the burner ring (D) is visible. The burner ring (D) is completely covered (except for the gas screen (E)). Place the fire glass (F) evenly in the fire bowl.
Operation Before each use, be sure to inspect the hose. Replace the hose if there are any signs of cutting, wear or abrasion. WARNING! During the initial lighting of the fire pit, stay away from the fire pit for 30 minutes as the fire glass may pop and cause injury to the face or eyes. CAUTION: Only use the pressure regulator and hose assembly supplied with the fire pit. The replacement pressure regulator and hose assemblies must be specified or supplied by the manufacturer. See Figure 8 1.
Troubleshooting Problem There is no power to the igniter. There is no spark between the ignition wire and the burner's hole while pushing the igniter button. The ignition wire does not conduct electricity. Solution Cause There is no igniter battery or the igniter battery is short of power. Replace with a new igniter battery. The igniter battery is incorrectly inserted. Reinsert the battery properly. The igniter is broken or cracked. Call customer service for a replacement part.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
