TOOLS REQUIRED Hammer (Not Included) Philip,s Screwdriver (Not Included) 2 - Persons Recommended ASSEMBLY RATING EASY----1► DIFFICULT The Assembly Rating is a 5-point system showing the level of effort needed to assemble a specific product.
Thank you for your purchase! We hope you enjoy this new addition to your home for many years to come. Our commitment to providing quality products does not simply end when you purchase our product. We fully stand behind our products from start to finish. Our customer service well help with assembly questions as well as, if necessary, replacing damaged or missing parts. To help expedite our service, please have these assembly instructions readily available, along with your order receipt.
PRE ASSEMBLY INTRODUCTION We understand building ready-to-assemble furniture can be a challenging experience for some. To help avoid confusion, we have provided some helpful tips that may speed up the process. Teamwork ALWAYS have at least two people to help with transporting and assembling the product to avoid potential injury and/or damage. Suitable Location Assembling near the area of the intended location is highly recommended.
ASSEMBLY AND CARE ADVICE FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. Turn clockwise to tighten and only tighten when step is completed or when instructed to do so. Position each part correctly and insert screws or bolts into their respective holes. Use the appropriate hand tools or power tools for assembly. Select steps, such as tightening screws and/or bolts, may require hand tools to avoid causing damage during assembly.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS Note : Every cam lock bolt must have a cam lock connector in order to fasten the parts together. cam bolt cam lock screwdriver 1 2 Screw the cam bolt into panel. Insert the cam bolt into the bolt hole of joint panel. 3 4 Align the cam lock with its side opening (or arrow) pointing to cam bolt. Turn the cam lock clockwise gently until it will not turn any more.
CONSOLE TABLE A I C J B D H PARTS B 1PC A 1PC C 2PCS D 2PCS E 1PC F 2PCS H 2PCS K 1PC I 1PC L 1PC M 1PC J 1PC N 1PC 2 24PCS 3 30PCS (8x30) 5 2PCS 6 4PCS 7 2PCS O 1PC Q 1PC P 1PC R 2PCS ACCESSORIES HARDWARE 1 24PCS G 2PCS 4 4PCS A1 1PC A2 1SET A3 6PCS A4 2SETS 1.
GET READY Please group boards as below. (92PCS Q1PC .. • I 11 @ 1PC 0 1PC G)2PCS . 0 0 1PC 0 . • f) 1PC Q 2PCS G)2PCS =□ O 1PC O 1PC 0 0 2PCS 0 0 0 G 2PCS Body 0 1PC bd 4D1PC Io. e G 1Pc 1Pc .
ASSEMBLY INSTRUCTIONS 1 2nd Holes of Inner Rail Hardware G) x 14 pcs Hardware ® x 4 pcs (8x30) Hardware @ x 2 pcs Hardware @ x 4 pcs 000 Front � Apply a dab of glue into dowel holes of panels before inserting dowels (#3).
ASSEMBLY INSTRUCTIONS 2 Hardware G) x 8 pcs Hardware @ x 24 pcs (8x30) [X2] [X2] 9 / 17
ASSEMBLY INSTRUCTIONS 3 Part (9x 1 pc Part 6)x 1 pc PartGx 2 pcs Part0x 2 pcs Hardware® x 4 0 G r:; owel hole '\@cm � 4 Part €)x 1 pc Partmx 2 pcs Hardware ® x 4 pcs Please refer to Page 5 for detailed instructions on how to fasten cam locks (#2) to cam bolts (#1 ).
ASSEMBLY INSTRUCTIONS 5 Hardware@ x 2 pcs 0 �owelhole Front �(TI] Top � 6 Part 0x 1 pc Part G)x 1 pc Hardware x 4 pcs Hardware @ x 2 pcs ® �owelhole �(TI] l•l:IU•H41■ Front �Top 11 / 17
ASSEMBLY INSTRUCTIONS 9 Part Ox 1 pc Part f)x 1 pc Part Ox 1 pc Part Gx 1 pc Hardware ® x 2 pcs 10 Hardware® x 2 pcs �cm owel hole r:-; Top Front) 13 / 17
ASSEMBLY INSTRUCTIONS 11 Hardware @ x 4 pcs 12 Hardware ® x 6 pcs 0 Top Front) 14 / 17
ASSEMBLY INSTRUCTIONS 13 Part 4ix 1 pc Part 4Dx 1 pc Part C!)x 1 pc Part Gx 1 pc Part@x 1 pc Hardware G) x Hardware® x Hardware@ x Hardware@ x Accessory[A2)x 2 2 2 4 1 pcs pcs pcs pcs set 14 Hardware (J) x 2 pcs 0 Top Fully extend drawer rails then align the rail's smallest hole to the drawer side panel's holes. Secure with bolts (#7).
ASSEMBLY COMPLETED Please ensure the furniture rests on an even and flat surface. If the product wobbles or feels loose, double-check all bolts and/or screws are properly tightened and secured. Keep this handy! Please retain this instruction manual and any order-related information for future reference.
/ 17