manual

ManualsBrandsHobbyKing ManualsCarsX-Car Beast Series ESC 1:8 Scale 150A

Alien Power System BEAST Series Sensored/Sensorless Brushless ESC for 1:8 scale Car or Truck

Thank you for purchasing the Alien Power System Brushless Electronic Speed Controller (ESC). The Alien Power System 1:8 Scale BEAST

Series ESC is specifically designed for operating 4 Pole Sensored/Sensorless brushless motors. Alien Power System Model have no control

over the correct use, installation, application or maintenance of these products, thus no liability shall be assumed nor accepted for any

damages, losses of costs resulting from the use of this item. Any claims arising from the operating, failure or malfunction etc. will be denied.

We assume no liability for personal injury, property damage or consequential damages resulting from our product or our workmanship. As far

as is legally permitted, the obligation for compensation is limited to the invoice amount of product in question.

Features:



Enhanced throttle response, excellent acceleration, linearity and driveability



Using advanced PC interface to set up or update the firmware



Using both of LED and LCD program card to make adjustments.



Adjustable BEC output 6.0V/8.4V



Multiple protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protection



Compatible with NOVAK, LRP , ORION brushless motor

BEAST Series 1:8 ESC Specifications:

Block Diagram :

Model 1:8 Beast-ZTWSS120A 1:8 Beast-ZTWSS150A

PN#Model 4212030 4215030

Cont.Current 120A 150A

Burst Current 760A 1080A

Resistance 0.0003ohm 0.0002ohm

Suitable Car 1:8 on-road and off-road cars/trucks for general

race or RTR application

1:5&1:8 on-road and off-road cars/trucks for

competitive race

Motor Type 4 Pole Sensorless and Sensored Brushless Motor

Suitable Brushless Motor 4P 3674 3.5D 2150KV 4P 4074 2Y 2150KV

Battery cell 2-6S Lipo/5-18S NiMH/NiCd

BEC Output 6.0V,8.4V adjustable/3A

Dimension(without fan) 55*48*37mm 55*48*37mm

Weight(g)

142g 159g

Summary of content (6 pages)

PAGE 1
Alien Power System BEAST Series Sensored/Sensorless Brushless ESC for 1:8 scale Car or Truck Thank you for purchasing the Alien Power System Brushless Electronic Speed Controller (ESC). The Alien Power System 1:8 Scale BEAST Series ESC is specifically designed for operating 4 Pole Sensored/Sensorless brushless motors.
PAGE 2
Note: Please refere to the illustration and connect the wire accordingly, wrong connection may get your ESC fried. Sensored Mode When using a Sensored Brushless motor, the Blue motor wire A, Yellow motor wire B and Orange motor wire C of the ESC must be connected with the Sensored motor wire A,B,C respectively. It is necessary to connect the Sensor wire to the “Sensor” socket on the ESC. Don’t change the wires sequence optionally.
PAGE 3
Percentage Drag Brake Motor Rotation Neutral Range BEC Output 0% 4% 8% 12% 15% 20% Normal 2% 6.0V Reverse 3% 8.4V 4% 5% 6% 10% 25% 30% Noted: Items above Colored are default settings Cutoff Voltage  Automatically detect the number of the cells According to the type of your batteries , set up the type of the batteries and Low Voltage Cutoff Threshold via PC software or program card.
PAGE 4
• High More power than efficiency so run time will reduce, and you should be monitoring motor heat. The higher KV or lower turn motors will generate heat quickly using this setting. A safe high temperature range is 165F to 180F (74° - 82° Celsius), going higher may damage your motor. • Very high This is maximum power and must be used with caution. Note : Any motor has the potential to over-heat in this setting.
PAGE 5
• 3% • 4% (Default) • 5% • 6% • 10% BEC Output 6.0V (Default) , 8.4V Alien Power System LCD Program Card Finish Alien Power System LCD Program card can be used to set up all brushless ESC for RC aircraft and car produced by Alien Power Systemprogram except Turbo SS120A. Users can choose their desired parameter at any time. LCD program Card Can be used as follows: a) Working as an individual device to set the parameters of ESC.
PAGE 6
“Menu”: Change the programmable items circularly; “Value”: Change the parameters of each programmable item circularly Note: Keeping the “Menu” or “Value” button holding can select the desired parameters quickly. “Reset”: Return to the default settings “OK”: Save the current parameters into the ESC. If you don’t press “OK” button, the customized settings will not be saved and updated into the ESC. If you just press “Menu” button, the customized settings are just saved into the program card, not into the ESC.