User's Manual

5 6
IMPORTANT NOTES
a. 8 x "AA" alkaline batteries (not included) for transmitter.(Diagram 2a)
b. 7.2V 2/3 "A" Ni-MH rechargeable battery pack (included).(Diagram 2b)
(A). Check the contents list and parts (Diagram 1):
BATTERIES REQUIREMENT
1 2
8 x 1.5V / 8 x"AA" / 8 x LR6
7.2V 2/3"A"900mAh
3 4
7 8 9 10
ITEM NO. 0202
CONTENTS
Air Knight
7.2V 2/3“A” 900 mAh
FAST CHARGER-OFF-SLOW CHARGER SWITCH
FAST-OFF-SLOW
CHARGING
SIGNAL LIGHT
BATTERY POWER
SIGNAL LIGHT
CAR CHARGER
CHARGER PLUG
CHARGER'S CONNECTOR
8 x LR6 / 8 x 1.5V / 8 x "AA" 8 x LR6 / 8 x 1.5V / 8 x "AA"
ON
OFF
ON
OFF
ON
OFF
speed control
trims
direction control
speed up
speed down
the adjustor of
vertical rudder
the adjustor of
horizontal rudder
2 Main wings
2 Joints
1 Wing cover
1 Fuselage
1 Horizontal wing
1 Vertical wing
1 Plastic sheet
1 Landing gear
1
2
3
4
5
6
7
8
9
10
11
12
13
1 Cross-headed screw driver
1 7.2 V 2/3 "A" rechargeable
battery pack screws
1 Antenna
12 Screws
1 Transmitter
16 Rubber bands
1 Car charger
1
2
14
15
3
4
5
6
7
8
9
10
12
11
14
15
13
LET'S GO FLYING
b). Take off from the ground.
Place the airplane on the ground and
switch “ON” the transmitter. Push the left
stick to the top on the transmitter and
propeller will rotate in the highest speed .
The airplane will move forword in full
speed and take off from the ground.
(Diagram 15)
CAUTIONS!
The person who holds the airplane should NOT touch the propeller
with any parts of his body to avoid injury.
1. Switch to "OFF" position, and plug into the electric power input of car,
connecting the rechargeable battery to the charger.
2. Switch to fast charge/slow charge, charging signal light or battery power
signal light is "ON" that means started charging.
3. After while(fast charge around 40 mins, slow charge around 80 mins),
charging signal light is "OFF" and battery is warm that means fully charged
for the rechargeable battery.
4. Switch to "OFF" position, take off the charger.
Attention:
1. Please do not charge the same rechargable battery continous two times.
2. Please do not use over 12V electric power or the other kind of battery
connect to the charger.
3. After fully charged battery are left over 24 hours, please charge again when
use.
4. The charger has build-in fuse, when the circuit or rechargable battery set are
overheated, the fuse will off the power for protection and safety used.
5. The situation of the liquid coming out from the battery, overheat of the
surface of the battery, smoke coming out from the battery are happened,
when it is charging. Please take out the battery and the charger immediately.
1
1
3
2
2
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Battery indicator
Warning light
Battery voltage indicators
1. BATTERIES INSTALLATION OF TRANSMITTER
1) Horizontally pull down the battery cover, depending on the polarity of
batteries installs batteries to the transmitter. (Diagram 3)
2) Transmitter battery power indicator has 5 LED light. (Red light is battery
power, yellow light is warning, green light are voltage indicators)
1. Check the contents list and all parts.
2. Study the instruction manual carefully before assembling.
3. Ensure all required batteries are ready.
4. Follow the instructions printed in manual when using the quick
charger
5. This product is intended for 14 years and up. (Adult supervision is
required if user is below 14 years old)
6. Do not fly over or near people, power pylon, buildings, highways, train
rails, vehicles, trees, lake, and airport.
7. Do not fly if wind speed is over 3 M/S(or over 5 mph)
2. PLANE ASSEMBLY
2. THE METHOD OF USING CHARGER AND
RECHARGEABLE BATTERY
1) Wing assembly
After match left/right wings
together, put the wings cover
on top of the left/right wings
and put 4 pieces of ø2.0
*
5PWB
screws. Installs and put 4
pieces of ø2.0
*
5PWB screws
into the joints.(Diagram 5)
2) Landing gear installation
Put the landing gear and plastic
sheet together to install into the
bottom of the plane. After that,
put the ø2.0
*
5PB screw to fix
it.(Diagram 6)
4) Wings and body installation
Put wings on top of the plane body and use r ubber bangs to fix it,
following the picture instruction.(Diagram 8)
Switch to “OFF” position
before installing the
battery.
Motor on/off switch
After connecting battery and charger, switch to “FAST” position for fast
charging(40 mins) or switch to “SLOW” position for slow charging (80mins).
The charger will be automatically cut off power. Charging time is around 40
minutes.
1. Insert a fully charged rechargeable battery into the plane body.(Diagram 11a)
2. Follow the direction showed in diagram to tied up the battery inside the
plane.(Diagram 11b)
3. Place the cover on top of the body then screw in one screw into both end of
the cover holes.(Diagram 11c)
4. BATTERY INSTALLATION
5. USE AND CONTROL OF TRANSMITTER
6. USE OF CONTROL STICK
1. First pull out the antenna to full position, and then switch to “ON” position
(all light will switch on). Advised to move trims to middle position.
2. Left control stick on the transmitter is for speed control. Turn over the plane
body and then switch “ON” the plane power, then the speed control stick is
pushed vertical up/down; the engine will start running and the propeller will
also start rotating. The amount of speed will change according to the
amount of movement apply to control stick. (Diagram 12)
1. Push the controller stick to right/left, the vertical rudder will respond and
move the same direction as the stick. the plane will turn direction during
fly according movement of the rudder.
2. Push the controller stick to up/down, the horizontal rudder will respond in
moving opposite direction. When the stick is pushed up, the rudder will flip
down, in result of that the plane will fly lower. otherwise pushing the stick
down will result in the plane fly higher.
Note:
When all three battery voltage indicators (green lights) are
switched off, that indicates the “AA” battery of the transmitter
need renewing.
1. Starting
a). Fly by hand.
Use left hand to hold the transmitter and
switch it "ON", right hand hold the
airplane. Left hand push the left stick on
the controller to the top and the propellers
rotate in high speed, throw out the
airplane horizontally and directly head to
the wind, watch the airplane flying
position and decide whether alignment is
required. (Diagram 15)
(Diagram 1)
(Diagram 2)
(Diagram 3)
(Diagram 4)
(a)
(b)
(Diagram 5)
(Diagram 6)
(Diagram 7)
(Diagram 12)
(Diagram 13)
(Diagram 14)
(Diagram 15)
(Diagram 17)
(Diagram 18)
(Diagram 19)
(Diagram 20)
(Diagram 16)
(Diagram 8)
(Diagram 9)
3) Vertical / Horizontal wings installation
Merge v ertical / horizontal wings together, and put it on the tail of the
plane, following the position of 4 screw holes. After that, use 4 pieces of
ø2.0
*
5PB screws to fix it.(Diagram 7)
(Diagram 10)
a b
c
(Diagram 11)
3. Place the plane end facing the used. Advice to adjust both vertical and
horizontal rudder to middle position. The trims on the rudder can be use to
change the position of rudder. (Diagram 13)
E-mail : [e-mail]
Website : www.hobbyengine.com.hk