INSTRUCTION MANUAL WARNING Please read and understand this manual, the operation and all safety aspects required for the safe operation of the product. Before use, if you feel that this product is not for you, please return it to the place of purchase. Manual Specifications and Description Changes The instruction manual, warranties, and other associated documentation are subject to change without notice. Hobbico assumes no responsibility for inadvertent errors to this manual. © 2016 RISE, a Hobbico company.
INTRODUCTION Thank you for purchasing the VUSION FPV RACER. We want the time you spend with your new R/C quadcopter to be fun and successful so please read the entire manual before beginning setup. If for any reason you think this R/C model is not for you, return it to the dealer immediately. Your dealer cannot accept returns on any model after final assembly. For the latest technical updates or manual corrections for the VUSION FPV RACER please visit the Rise web site at www.explore-rise.com .
AMA We urge you to join the AMA (Academy of Model Aeronautics) and a local R/C club. The AMA is the governing body of model aviation and membership is required to fly at AMA clubs. Though joining the AMA provides many benefits, one of the primary reasons to join is liability protection. Coverage is not limited to flying at contests or on the club field. It even applies to flying at public demonstrations and air shows. Failure to comply with the Safety Code may endanger insurance coverage.
material used for final assembly, no liability shall be assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user accepts all resulting liability. If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit immediately in new and unused condition to the place of purchase.
SETUP The VUSION FPV RACER is completely assembled. All the bolts have been set to the proper torque and have thread locking compound applied where needed to keep them secure. FPV ANTENNA Always attach the FPV VTX antenna before connecting the battery to the Vusion. If the quadcopter is operated without the FPV antenna, the VTX could be damaged. BATTERY CHARGING Plug the AC wall adapter into a 120V outlet and connect the balance charger to the wall adapter. The power LED will illuminate solid RED.
RADIO SYSTEM Insert 4 AA batteries in the battery compartment in the back of the transmitter. Turn on the transmitter and connect the battery to the Vusion. The quadcopter should beep twice when it is linked to the transmitter. NOTE: Always turn the transmitter on first. FLYING MOTOR ARMING While the throttle is at its lowest setting, hold the yaw control (left stick) to the right to arm the motors. Holding the yaw control to the left while the throttle is at its lowest setting will disarm the motors.
Mode 2: This mode still has autolevel, but has higher roll rates and a high tilt angle setting. This mode is for the more experienced pilot. Mode 3: This mode (rate mode) has no limits on tilt and faster roll rates. The quad will not autolevel in this mode. This mode offers the most maneuverability but requires the pilot to be able to control the attitude of the quadcopter themselves. It normally takes a week or two of practice to learn to fly rate mode.
If the VTX must use a different FPV channel, remove the rear cover by pushing down on the edge of the cover and sliding it back. Push Tap the red button to cycle through the 8 channels that are available. To see current band, channel and frequency on the monitor, select Band E with the “B” button and tap the CH button until the screen displays the feed from the camera. Flying FPV is more difficult than Line of Sight because it is difficult to determine altitude with just the camera.
battery voltage drops to 10.5V. You should land the quadcopter as soon as possible when you hear or see the alarm to avoid damaging the battery. The Vusion will autoland when the battery voltage gets below 9.7V. The flight battery should always be recharged before it is stored. Warning: Your battery life will be reduced and the battery can be damaged any time the battery voltage is below 9V. Charging a LiPo battery that is damaged in any way can pose a fire hazard.
Turn on the transmitter and connect the battery to the Vusion. Perform a sensor calibration as described in Maintenance Section to verify that the control board is receiving signals from the receiver. The quadcopter will not enter the calibration mode if the receiver is wired incorrectly. Arm the motors by holding the yaw control to the right. Advance the throttle and check for a motor not running. Bring the throttle back down to its lowest setting. The motors should stop after 5 seconds.
LINK TRANSMITTER If the Vusion does not make a double chime when it is powered up and the transmitter is on, it may need to be relinked. 1. Turn off the transmitter. 2. Remove the rear cover. Press down on the rear edge and slide the cover out of the frame. 3. Connect the battery to the Vusion. 4. Press and hold the red button until the red and white LEDs on the board start flashing. 5. Turn on the transmitter. The board should make the second chime immediately.
SEPARATE FRAME To remove the Camera, VTX or Control Module, the frame must be separated. All 4 arms must be removed first.
SPARE PARTS 1 2 3 4 5 6 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 RISE2020 RISE2009 RISE2010 RISE2019 RISE2001 RISE2017 RISE2018 RISE2007 RISE2025 RISE2015 RISE2006 RISE2004 RISE2003 RISE2005 RISE2000 RISE2026 RISE2022 RISE2002 RISE2013 RISE2011 RISE2012 RISE2014 RISE2016 RISE2008 RISE2021 RISJ2000 FPV VTX Antenna Prop Nuts CW/CCW Props CW/CCW 2 Yellow/2 Black Camera VTX CASE Top Cover 25mW VTX Camera 200mW VTX Camera FC Board Module with Arm sockets Control Board Dampers (4) Frame Left and Right
™ BATTERY PRECAUTIONS The RISE Vusion uses a lithium polymer (LiPo) battery. Follow these precautions to ensure safe and trouble-free operation. • ALWAYS disconnect the battery from the quadcopter when not in use. • Do not attempt to use this charger with NiCd or NiMH battery packs. • Do not attempt to use a damaged battery. • This product contains a LiPo battery that must be recycled or disposed of properly. • Do not leave the charger unattended while charging.
