Installation Guide

ManualsBrandsHM Electronics ManualsElectronicsRemote Transceiver

Quick Reference Installation Guide

HM ELECTRONICS, INC.

2848 Whiptail Loop, Carlsbad, CA 92010 USA

Phone: 1-800-848-4468 Fax: 858-552-0172

Website: www.hme.com Email: support@hme.com

HME# PUB - 000xx

Rev A 09/01/20

RT7000 REMOTE TRANSCEIVER

The RT7000 Remote Transceiver facilitates Base Station to Headset

communication. It uses a wired connection to the Base Station but

is wireless for Headset communication. Up to four RT7000s can be

connected to the Base Station for additional coverage.

TOOLS/EQUIPMENT REQUIRED

• Drill and drill bit set

• Screwdriver (Phillips #2), tape measure, pencil/maker

• Fish stick, cable ties, safety glasses, ladder

INSTALLATION, SETUP, AND OPERATION

1. Survey the premises to determine a good location to mount

the RT7000 (see Remote Transceiver RT7000 Notes on the next

page).

2. Once a good location is selected, route the Ethernet cable from

the Base Station to the RT7000 location.

3. Loosely mount the Remote Transceiver in an optimal location

(until range tested with a roving headset using the Installation

Wizard via the Base Station in step 5.

4. Connect the Ethernet cable to the RJ45 port on the rear of the

RT7000 (see Fig. 2) and the other end to one of the available

ports on the Base Station (see Fig. 4 and Table 1).

5. At the Base Station LOG IN to the system, go to SYSTEM, then

the ADVANCED tab and select “Installation” from the drop-

down menu. Tap the “Start Installation Wizard” button.

This opens the Installation Wizard as shown in Fig. 3.

Fig. 3

6. Follow the Transceiver Installation steps that follow. Once you

have used a headset in Reception Location Mode to walk the

premises to determine the mounting location is good, move

on to the next step. If the mounting location is not a good one,

move the Remote Transceiver to another location and repeat

steps 1 through 6, until a good location is found.

7. Drill two holes 6.625 inches (16.83 cm) apart along a horizontal

axis on the wall (avoid electrical or plumbing obstructions).

8. Install the provided hardware but do not tighten, leave a gap (~

¹/8

inch (3.2 mm)) between the screw heads and wall.

9. Align the RT7000 mounting holes with the two screws (Fig. 2).

Fig. 1

Fig. 2

Fig. 4

1 2

3 4

RT7000 TRANSCEIVER

Front View

RT7000 TRANSCEIVER

Rear View

THIS SIDE UP

Mounting Holes

RJ45 Port

for Ethernet cable

1 2

3 4

RT7000 TRANSCEIVER

Front View

RT7000 TRANSCEIVER

Rear View

THIS SIDE UP

Mounting Holes

RJ45 Port

for Ethernet cable

NEXEO BASE STATION

PCBA (Partial)

Remote

XCVR 1

Remote

XCVR 2

Remote

XCVR 3

Remote

XCVR 4

Ethernet/

Network

Telephone

Interface

Timer Greet

Veh Detect 1

Timer Greet

Veh Detect 2

Veh Detect

Inputs

Alert

Inputs

Remote

Switches

Early

Warnings

Power

DC +

DC -

GND

Micro

USB

J200

J600

J201 J800 J801

J802

J805

J804

J803

J2003

J3000

J4500 J4501

J1400

J3200

J3400

J3600

J3800

1 1 1

Serial

Debug

USB

J?301

J?300

PCBA

Side View Detail

Ethernet

(Network)

Remote

Module 1

Remote

Module 2

Remote

Module 3

Remote

Module 4

Power

Transceiver (x4)

1 2

3 4

Vertical Mount Only

(this way up)

REMOTE TRANSCEIVER

(RT7000)

Summary of content (6 pages)

PAGE 1
Quick Reference Installation Guide RT7000 REMOTE TRANSCEIVER The RT7000 Remote Transceiver facilitates Base Station to Headset communication. It uses a wired connection to the Base Station but is wireless for Headset communication. Up to four RT7000s can be connected to the Base Station for additional coverage.
PAGE 2
10. Mount the RT7000 over the screw heads until flush against the wall, then slide it down onto the screws to secure it in place and tighten hardware. 11. The other end of the Ethernet cable is connected to the Base Station (see Fig. 4 and the Table 1 for connections). 12. The Base Station provides power to the RT7000. So when connected, the center LED in the circle on the front of the RT7000 turns on solid green. 13.
PAGE 3
REGULATORY COMPLIANCE Applicant Name: HM Electronics, Inc. Applicant Address: 2484 Whiptail Loop, Carlsbad CA 92010, United States Manufacturer Name: HM Electronics, Inc. Manufacturer Address: 2484 Whiptail Loop, Carlsbad CA 92010, United States Country of Origin: USA Brand: HME Caution: All products are compliant with regulatory requirements detailed in this document when the user follows all installation instructions and operating conditions per HME specifications.
PAGE 4
INDUSTRY CANADA COMPLIANCE STATEMENT Avis de conformité à la réglementation d'Industrie Canada Cet appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d’interféence, et (2) cet appareil doit accepter toute interféence radioéectrique subie, mêe si l’interféence est susceptible d’en compromettre le fonctionnement.
PAGE 5
NEW ZEALAND COMPLIANCE STATEMENT User Restriction in the 5Ghz band: This device is restricted to indoor use only when operating in 51505250MHz. EUROPEAN UNION (CE MARK) The CE marking indicates compliance with the following directives and standards, whenever applicable to the product in question.
PAGE 6
most HME products being sold into the EU as of August 13, 2005. Manufacturers, distributors and retailers are obliged to finance the costs of recovery from municipal collection points, reuse, and recycling of specified percentages per the WEEE requirements. INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN THE EUROPEAN UNION The symbol shown below is on the product or on its packaging which indicates that this product was put on the market after August 13, 2005 and must not be disposed of with other waste.