Installation Instructions

ManualsBrandsHLI Solutions ManualsElectronicsPIR Occupancy/Daylight Sensor

currentlighting.com/

without notice. All values are design or typical values when measured under laboratory conditions.

Page 1 of 5

Rev 08/01/22

NXSMP2-LMI_install_sheet_R01

93147266 Rev. A

NXSMP2 Series Sensors

Low Mount Indoor Sensors

LMI INSTALLATION INSTRUCTIONS

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

PRECAUTIONS

Read and understand all instructions before beginning installation.

CAUTION: FOR USE WITH CLASS 2, LOW VOLTAGE SYSTEMS ONLY. DO NOT USE IN HIGH VOLTAGE APPLICATIONS.

NOTICE: Class 2 Device, 12-24V, 10mA

NOTICE: Suitable for Use in Other Environmental Air Space (Plenums) in Accordance with Section 300.22 (c) of the National

Electrical Code.

NOTICE: For installation by a licensed electrician in accordance with National and/or Local Electrical Codes and the following

instructions.

Confirm device ratings are suitable for application prior to installation. Use of this device in applications beyond its specified ratings

other than its intended use may cause an unsafe condition and will void manufacturer’s warranty.

Use only approved materials and components (i.e. wire nuts, electrical box, etc.) as appropriate for installation.

NOTICE: DO NOT INSTALL IF PRODUCT APPEARS TO BE DAMAGED.

NOTICE: Do not use outdoors. For In-fixture use only.

NOTICE: Do not use this equipment for other than its intended use.

REGULATORY INFORMATION

1. Contains Transmitter Module FCC ID: YH9NXSMP2 IC: 9044A-NXSMP2

1. This device complies with FCC part 15 Rules. Operation is subject to the following two conditions: This device may not cause

harmful inference.

2. This device must accept any interference received, including interference that may cause undesired operation.

2. FCC Interference Statement (Part 15.105(b)): This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

3. FCC Part 15 Clause 15.21: Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

4. ISED RSS-Gen Notice

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

1. The device may not cause interference; and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage;

2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

SAVE THESE INSTRUCTIONS AND PROVIDE TO OWNER AFTER INSTALLATION IS COMPLETED

Summary of content (5 pages)

PAGE 1
NXSMP2 Series Sensors Low Mount Indoor Sensors LMI INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS PRECAUTIONS Read and understand all instructions before beginning installation. CAUTION: FOR USE WITH CLASS 2, LOW VOLTAGE SYSTEMS ONLY. DO NOT USE IN HIGH VOLTAGE APPLICATIONS. NOTICE: Class 2 Device, 12-24V, 10mA NOTICE: Suitable for Use in Other Environmental Air Space (Plenums) in Accordance with Section 300.22 (c) of the National Electrical Code.
PAGE 2
DESCRIPTION NXSMP2 Series Digital Smart Sensors are a combination PIR Occupancy Sensor and Closed Loop Daylight sensor specifically designed for installation within a lighting fixture and ceiling mount applications. When used with corresponding NXFM2 Series Fixture Module, the NXSMP2 Series Sensors can be programmed to provide Automatic On/Off control based on occupancy and/ or Automatic Light Level Control based on the amount of ambient daylight. The NXSMP2 Series sensors also include a wireless 2.
PAGE 3
INSTALLATION FOR IN-FIXTURE DEPLOYMENT 6. Choose a mounting location on the housing or lens with a flat surface where the sensor face and sensor lens will be oriented in the downward position as close to level as possible. NOTE: The sensor should be clear from obstructions to ensure proper detection. 7. Once a position is selected a 1-3/16" to 1-1/4" round opening in the housing or lens needs to made in order for the sensor to slide into position.
PAGE 4
WIRING DIAGRAMS NXSMP2-LMI NXSMP2-LMI Pink (-) NXFM2-1R2D-O-UNV NXSMP2-LMI with NXFM2-1R2D-O-UNV Pink wire replace previous gray wire. Unit with a gray instead of pink wire should be wired as the pink wire shown in the diagram. NXSMP2-LMI NXSMP2-LMI NXFM2-1R2D-I-UNV Pink (-) NXSMP2-LMI with NXFM-1R2D-I-UNV Pink wire replace previous gray wire. Unit with a gray instead of pink wire should be wired as the pink wire shown in the diagram. 93147266 Rev. A currentlighting.com/ © 2022 HLI Solutions, Inc.
PAGE 5
WIRING DIAGRAMS NXSMP2-LMI NXSMP2-LMI NXFM2-LV NXSMP2-LMI with NXFM2-LV Pink wire replace previous gray wire. Unit with a gray instead of pink wire should be wired as the pink wire shown in the diagram. 93147266 Rev. A currentlighting.com/ © 2022 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions.