Intro. Thank you for purchasing the FLASH 7 transmitter. FLASH 7 is composed of diverse features to maximize customer’s R/C experiences. Please read carefully to become familiar with FLASH 7 under your control. After reading this, please keep this manual for easy reference. Product Specifications - Frequency Range : 2.4056GHz~2.4776GHz(Opti-Mini), 2.406GHz~2.480GHz(S.L.T) - Modulation : Frequency Hopping Spread Spectrum (FHSS) - Tx Power : Max. 100mW - Channel : 121Ch(Opti-Mini), 75Ch(S.L.
- Function Button : Use this button when to combine the OPTIMA receiver and the built-in FHSS 2.4GHz module or to Set normal/scan mode or Power off when check the range. Features of OPTIMA Series Rx OPTIMA 6, 7 receivers are compatible with built-in FHSS 2.4GHz module of FLASH 7 and They have many necessary functions for the 2-way communication radio control.
- Low voltage warning function of Rx battery : OPTIMA Rx is mounted the 2-way function that send the occurred low voltage data of Rx to Tx during the flight. OPTIMA receiver wiring Glow engine / Petrol engine / Electric wiring diagram of the Plane. - The following figure illustrates the battery wiring that is used Li-Po 2Cell or 4.8 ~ 6V Ni-MH. - The following figure illustrates the wiring that BEC supply power to Rx and servo also the Electronic transmission supply power to the motor.
- Use the BEC when servo current consumption exceeds the current that supplied by ESC. - (Warning – Please following this procedures whenever put the power to the transceiver system. - Power ON: Power on the Tx first then power on the Rx next. - Power OFF: Power off the Rx first then power off the Tx next.) Pre-flight checks Please put the power to follow above warning order before use the engine or motor. And flight after check that all servos operate smoothly.
1. Press and hold the Back button and Menu button at the same time then go to the menu screen after turn on the power. 2. Turn the Menu button then go into SPECTRA Menu, then select the type of Rx, then make sure the RGB LED colors changes after BINDING. 3. Please turn on the power while Rx’s LINK button is pressing. Release the LINK button after check that red and green LED of Rx are turned on. Rx will show you to turn on the red and green LED if Rx operating is normal. 4.
status. 4. Complete to save the Fail-safe position. 5. Power off the Rx first then power off the Tx next. 6. Enable the transmission system then turn off the transceiver. 7. Check the servo move to the Fail-safe position. - Fail-safe Setting TEST 1. The flight move to the any place that is not the Fail-safe setting. 2. It is the normal Fail-safe setting if the servo moves to the Fail-safe position you set lastly after you turn off the Tx. - The way to re-enable the Hold mode in Fail-safe mode. 1.
How work the Power-down mode? 1. Turn of the power of FLASH7 then Press and hold the back and menu button at the same time then go to the Menu screen. 2. Turn the menu button then go into the SPECTRA menu. Select the Yes after press the menu button on the Range check. 3. Check the minimum distance more than 30 meters between the Tx and Rx then make sure the Tx and Rx work normally in the Power-down time. 4. Press the menu button if you want to change to the Normal mode.
Warnings and Precautions - Don’t steer this in the busy street. - Don’t steer this in the rain and on the standing water. - Don’t steer this after drink alcohol. - Always check the remaining battery power. - Always power on the Tx first then power on the Rx next to prevent failure.
WARNING & SAFETY INFORMATION Safety Symbols Warning 9JGP GPEQWPVGTKPI VJKU U[ODQN KP VJG OCPWCN [QW OWUV HQNNQY VJGUG 㿋 # FCC Information 6JKU FGXKEG EQORNKGU YKVJ RCTV QH VJG (%% 4WNGU 1RGTCVKQP KU UWDLGEV VQ VJG HQNNQYKPI VYQ EQPFKVKQPU TGEQOOGPFCVKQPU VQ CXQKF KTTGRCTCDNG FCOCIG VQ [QWT ECT U[UVGO QT 6JKU FGXKEG OC[ PQV ECWUG JCTOHWN KPVGTHGTGPEG CPF EQPPGEVGF FGXKEGU QT VQ CXQKF CEEKFGPVU YKVJ KPLWTKGU QT FGCVJ 6 JKU FGXKEG OWUV CEEGRV CP[ KPVGTHGTGPEG TGEGKXGF KPENWFKPI