Cordless Impact Wrench Akku-Schlagschrauber Clé à choc à batterie Avitatore ad impulso a batteria Snoerloze slagmoeraanzetter Llave de impacto a batería Chave de impacto a bateria WR 18DSHL Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste istruzioni. Deze gebruiksaanwijzing s.v.p.
1 2 5 3 4 1 8 1 3 9 2 6 1 7 4 5 2 6 0 C B 8 D E A 7 8 9 I F G 3mm 9.
English Deutsch Français Italiano 1 Rechargeable battery Batterie Batterie rechargeable Batteria ricaricabile 2 Latch Schnapper Loquet Fermo 3 Battery cover Batterieabdeckung Couvercle de batterie Coperchio per la batteria 4 Terminals Anschlüsse Bornes Terminali 5 Ventilation holes Belüftungslöcher Orifices de ventilation Fori di ventilazione 6 Push Drücken Pousser Spingere 7 Pull out Herausziehen Tirer Estrarre 8 Handle Griff Poignée Impugnatura 9 Pilot lamp 0
Nederlands Español Português 1 Oplaadbare batterij Batería recargable Bateria de recarregável 2 Vergrendeling Enganche Lingüeta 3 Batterijdeksel Tapa de batería Tampa da bateria 4 Aansluitpunten Terminales Terminais 5 Ventilatieopeningen Orificios de ventilación Orifícios de ventilação 6 Drukken Presionar Apertar 7 Uittrekken Sacar Retirar 8 Handgreep Mango Cabo 9 Controlelampje Lámpara piloto Lâmpada piloto 0 Lijn Línea Linha A B Na insteken Zeschoekige bus Tras
Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Symbole WARNUNG Die folgenden Symbole werden für diese Maschine verwendet. Achten Sie darauf, diese vor der Verwendung zu verstehen. Lesen Sie sämtliche Sicherheitshinweise und Anweisungen durch.
English (Original instructions) GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit.
English 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
English WARNING In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions. 1. Make sure that swarf and dust do not collect on the battery. 䡬 During work make sure that swarf and dust do not fall on the battery. 䡬 Make sure that any swarf and dust falling on the power tool during work do not collect on the battery. 䡬 Do not store an unused battery in a location exposed to swarf and dust.
English 2. Battery installation Insert the battery while observing its polarities (see Fig. 2). OPTIONAL ACCESSORIES (Sold separately) 1. Battery (BSL1830) CHARGING Optional accessories are subject to change without notice. APPLICATION Tightening and loosening of all types of bolts and nuts, used for securing structural items BATTERY REMOVAL/INSTALLATION 1. Battery removal Hold the handle tightly and push the battery latch to remove the battery (see Fig. 2). CAUTION: Never short-circuit the battery.
English Regarding electric discharge in case of new batteries, etc. As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2-3 times.
English As the remaining battery indicator shows somewhat differently depending on ambient temperature and battery characteristics, read it as a reference. NOTE: 䡬 Do not give a strong shock to the switch panel or break it.It may lead to a trouble. 䡬 To save the battery power consumption, the remaining battery indicator lamp lights while pressing the remaining battery indicator switch. 3. How to use the LED light Every time you press the light switch on the switch panel, the LED light lights or goes off.
English 4. Inspecting the carbon brushes (Fig. 9) The motor employs carbon brushes which are consumable parts. Since and excessively worn carbon brush can result in motor trouble, replace the carbon brush with new ones when it becomes worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely whthin the brush holders. NOTE: When replacing the carbon brush with a new one, be sure to use the Hitachi Carbon Brush Code No. 328481. 5.
Deutsch (Übersetzung der Original-Gebrauchsanweisung) ALLGEMEINE SICHERHEITSHINWEISE FÜR ELEKTROGERÄTE WARNUNG Lesen Sie sämtliche Sicherheitshinweise und Anweisungen durch Wenn die Warnungen und Anweisungen nicht befolgt werden, kann es zu Stromschlag, Brand und/oder ernsthaften Verletzungen kommen. Bitte bewahren Sie alle Warnhinweise und Anweisungen zum späteren Nachschlagen auf.
Deutsch d) Lagern Sie nicht benutzte Elektrowerkzeuge außerhalb der Reichweite von Kindern, lassen Sie nicht zu, dass Personen das Elektrowerkzeug bedienen, die nicht mit dem Werkzeug selbst und/oder diesen Anweisungen vertraut sind. Elektrowerkzeuge in ungeschulten Händen sind gefährlich. e) Halten Sie Elektrowerkzeuge in Stand.
Deutsch 11. 12. 13. 14. 15. 16. 17. 18. 19. Die Batterie immer bei einer Temperatur von 0 40°C laden. Laden bei einer Temperatur die niedriger als 0°C is twird gefährliche Überladung verursachen. Die Batterie kann nicht bei einer Temperatur über 40°C geladen werden. Die beste Temperatur zum Laden wäre von 20 - 25°C. Das Ladegerät nicht fortlaufend laden. Nach Beendung einer Ladung, lassen Sie das Ladegerät ungefähr 15 Minuten ruhen bevor die nächste Batterieladung unternommen wird.
Deutsch 䡬 Legen Sie keine elektrisch leitenden Späne, Nägel, Stahldraht, Kupferdraht oder anderen Draht in den Aufbewahrungskoffer. 䡬 Setzen Sie den Akku entweder in das Gerät ein oder lagern Sie ihn, um Kurzschlüsse zu vermeiden, indem Sie ihn in die Batterieabdeckung hineindrücken, bis die Belüftungslöcher verdeckt sind. (Siehe Abb.
Deutsch Tafel 1 Anzeigen der Kontrollampe Vor dem Die Bereitschafts- Laden anzeige leuchtet oder Beim Laden blinkt rot. Blinkt Leuchtet für 0,5 Sekunden. Erlischt für 0,5 Sekunden. (Aus für 0,5 Sekunden) Leuchtet Leuchtet kontinuierlich Blinkt Laden durchgeführt Laden unmöglich Leuchtet für 0,5 Sekunden. Erlischt für 0,5 Sekunden. (Aus für 0,5 Sekunden) Flackert Leuchtet Die Wegen Bereitschafts- Überhitzung anzeige angehalten leuchtet grün. Leuchtet für 0,1 Sekunden. Erlischt für 0,1 Sekunden.
Deutsch 2. Prüfen der Batterie Nachsehen, ob die Batterie sicher und fest sitzt. Eine locker eingesetzte Batterie kann herausfallen und stellt somit eine Gefahr dar. 3. Wahl der Muffe entsprechend der Schraube Für die anzuziehende Schraube sollte die passende Muffe verwendet werden. Durch eine nicht passende Muffe wird nicht nur das Anzugsdrehmoment verringert, sondern auch die Muffe oder Muffer beschädigt.
Deutsch Wenn die Mutter nur locker auf der Schraube sitzt, kann sich die Schraube mit der Mutter mit drehen, wodurch man irrtümlich glauben kann, sie sei ordnungsgemäß angezogen. Stoppen Sie in diesem Fall die Einwirkung auf die Mutter und halten Sie den Schraubenkopf mit einem Schraubenschlüssel fest, bevor Sie wieder auf die Mutter einwirken, oder ziehen Sie die Schraube und die Mutter zuerst von Hand an, um zu vermeiden, dass sie durchdrehen. VORSICHTSMASSREGELN ZUR VERWENDUNG 1.
Deutsch ACHTUNG: Stellen Sie unbedingt sicher, dass der Kabelschuh der Kohlebürste in den Kontaktteil außerhalb des Bürstenrohrs eingeschoben wird. (Einer der beiden vorhandenen Kabelschuhe muß eingeschoben werden.) Vorsicht ist erforderlich, da Fehler bei dieser Tätigkeit zu einem verformten Kabelschuh der Kohlebürste und frühzeitigen Motorstörungen führen können. 6.
Français (Traduction des instructions d'origine) AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX POUR L’OUTIL AVERTISSEMENT Lire tous les avertissements de sécurité et toutes les instructions. Ne pas suivre les avertissements et instructions peut donner lieu à un choc électrique, un incendie et/ou une blessure sérieuse. Conserver tous les avertissements et toutes les instructions pour pouvoir s'y reporter ultérieurement.
Français condition pouvant affecter le fonctionnement de l’outil. En cas de dommages, faire réparer l’outil avant de l’utiliser. De nombreux accidents sont dus à des outils mal entretenus. f) Garder affûtés et propres les outils permettant de couper. Des outils destinés à couper correctement entretenus avec des pièces coupantes tranchantes sont moins susceptibles de bloquer et sont plus faciles à contrôler. g) Utiliser l’outil, les accessoires et les lames etc.
Français 15. 16. 17. 18. 19. Ne court-circuitez jamais la batterie rechargeable. Le fait de cour-circuiter la batterie génèrera un courant électrique élevé et une surchauffe, ce qui entraînera la brûlure ou l’endommagement de la batterie. Ne jetez pas la batterie au feu. Elle pourrait exploser. Ne pas introduire d’objets métalliques ou des produits inflammables dans les fentes d’aération du chargeur, cela provoquera un choc électrique ou endommagera le chargeur.
Français SPECIFICATIONS OUTIL ELECTRIQUE Modèle Tension Vitesse sans charge Boulon ordinaire Capacité Boulon hautement extensible Couple de serrage (Maximum) Batterie rechargeable Poids UC18YRSL Tension de charge M12 – M16 480 N·m BSL1830: Li-ion 18 V (3,0 Ah 10 accus) 3,4 kg CHARGEUR Modèle WR18DSHL 18 V 1500 min–1 M12 – M22 14,4 V – 18 V Poids 0,6 kg ACCESSOIRES STANDARDS En plus de l’outil principal (1), l'emballage contient les accessoires énumérés dans le tableau ci-après. 1 Chargeur ........
Français Tableau 1 Indications de la lampe témoin La lampe témoin s’allume ou clignote en rouge. La lampe témoin s’allume en vert. Avant la recharge Clignote Pendant la recharge S’allume S’allume sans interruption Recharge terminée Clignote S’allume pendant 0,5 seconde. Ne s’allume pas pendant 0,5 seconde. (Eteint pendant 0,5 seconde) Recharge impossible Clignote S’allume pendant 0,1 seconde. Ne s’allume pas pendant 0,1 seconde.
Français S’il n’y a rien d’amormal, il est alors probable que la batterie ou le chargeur fonctionne mal. Dans ce cas, les enlever et les porter à un réparateur agréé. AVANT LA MISE EN MARCHE 1. Préparatifs et inspection de la zone de travail S’assurer que la zone de travail remplit les conditions citées dans le chapitre des précautions générales. 2. Vérification de la batterie S’assurer que la batterie est fermement maintenue en place.
Français 4. Serrage et desserrage des boulon Commencer par sélectionner une douille hexagonale qui convient pour le boulon ou l’écrou. Puis, monter la douille sur le piton, et saisir l’écrou à serrer avec la douille hexagonale. Tout en tenant la clé dans l’alignement du boulon, appuyer sur l’interrupteur pour percuter l’écrou pendant plusieurs secondes. Si l’écrou n’est pas serré à fond sur le boulon, le boulon risque de tourner en même temps que l’écrou, empêchant d’obtenir le couple de serrage voulu.
Français ATTENTION: Bien veiller impérativement à insérer le clou du balai en carbone dans la section de contact à l’extérieur du tube de balai. (On pourra insérer n’importe lequel des deux clous fournis.) Procéder avec précaution, car une erreur dans cette opération risque de déformer le clou du balai en carbone et d’endommager précocement le moteur. 6. Nettoyage de l’extérieur Quand la clé à choc est sale, essuyez-la avec un chiffon sec et doux ou un chiffon imbibé d’eau savonneuse.
Italiano (Traduzione delle istruzioni originali) AVVERTIMENTI GENERALI DI SICUREZZA SUGLI UTENSILI ELETTRICI AVVERTENZA Leggere tutti gli avvertimenti di sicurezza e tutte le istruzioni. La mancata osservanza degli avvertimenti e delle istruzioni potrebbe essere causa di scosse elettriche, incendi e/o gravi lesioni. b) c) Salvare tutti gli avvertimenti e le istruzioni per riferimenti futuri.
Italiano e) Manutenzione degli elettroutensili. Verificare che non vi siano componenti in movimento disallineati o bloccati, componenti rotti o altre condizioni che potrebbero influenzare negativamente il funzionamento dell'elettroutensile. In caso di guasti, provvedere alla riparazione dell'elettroutensile prima di riutilizzarlo. Molti incidenti sono causati da una scarsa manutenzione. f) Mantenere gli strumenti di taglio affilati e puliti.
Italiano 15. 16. 17. 18. 19. Non provocare assolutamente mai dei cortocircuiti alla batteria ricaricabile. Il fenomeno provoca surriscaldamento e grande corrente electrica. Può quindi causare bruciature o danni alla batteria. Non gettare la batteria nel fuoco. Può esplodere. Non inserire nessun oggetto nelle fessure di ventilazione del caricatore.
Italiano CARATTERISTICHE UTENSILE ELETTRICO Modello Voltaggio Velocità a vuoto Bullone ordinaire Capacità Bullone a trazione WR18DSHL 18 V 1500 min–1 M12 – M22 M12 – M16 Forza di torsione (Massimo) Batteria ricaricabile Peso CARICATORE Modello 480 N·m BSL1830: Li-ion 18 V (3,0 Ah 10 celle) 3,4 kg UC18YRSL Votaggio di carica 14,4 V – 18 V Peso 0,6 kg ACCESSORI STANDARD Oltre all’unità principale (1), l’imballaggio contiene gli accessori elencati nella tabella di seguito.
Italiano Tabella 1 Indicazioni della spie La spia si illumina o lampeggia rosso. La spia si illumina di colore verde. Prima della Lampeggia Si illumina per 0,5 secondi. Non si illumina per 0,5 secondi. (Spento per 0,5 secondi) carica Durante la carica Si illumina Si illumina stabilmente Carica completa Lampeggia Si illumina per 0,5 secondi. Non si illumina per 0,5 secondi. (Spento per 0,5 secondi) Carica Lampeggia Si illumina per 0,1 secondi. Non si illumina per 0,1 secondi.
Italiano 3. Scelta dell’alloggiamento adatto per il bullone da stringere Usare sempre un alloggiamento adatto per il bullone da stringere. Se l’alloggiamento non è adatto, si ottiene non solo un serraggio insufficiente, ma anche il danneggiamento dell’alloggiamento stesso o del dado. Se l’alloggiamento esagonale o quandrato è deformto, il montaggio di esso sul busamento non può essere realizzato a dovere, e si ottiene di conseguenza una diminuzione della forza di serraggio.
Italiano PRECAUZIONI NELL’USO MANUTENZIONE E CONTROLLI 1. Riposo dell’unità dopo lavoro continuo Dopo un lavoro continuo di serraggio bulloni, lasciar riposare l’unità per 15 minuti circa quando si sostituisce la batteria. La temperatura del motore, interruttore, ecc. sale se si riprende immediatamente il lavoro dopo la sostituzione della batteria, con il rischio che si bruci tutto. NOTA: Non toccare le parti metalliche, perché diventano molto calde durante il funzionamento continuo. 2.
Italiano 7. Conservazione Conservare l’avvitatore a impulso a batteria ad una temperatura inferiore ai 40°C e non a portata di mano di bambini. NOTA: Assicurarsi che la batteria sia completamente carica quando viene conservata per un lungo periodo (3 mesi o più). Una batteria con minore capacità potrebbe non essere in grado di essere caricata quando viene utilizzata, se conservata per un lungo periodo. 8.
Nederlands (Vertaling van de oorspronkelijke aanwijzingen) ALGEMENE VEILIGHEIDSWAARSCHUWINGEN VOOR ELEKTRISCH GEREEDSCHAP WAARSCHUWING Lees alle waarschuwingen en instructies aandachtig door. Nalating om de waarschuwingen en instructies op te volgen kan in een elektrische schok, brand en/of ernstig letsel resulteren. Bewaar alle waarschuwingen en aanwijzingen voor eventuele naslag in de toekomst.
Nederlands c) Haal de stekker uit het stopcontact voordat u de voeding en/of de accu van het elektrisch gereedschap losmaakt, afstellingen verricht, accessoires verwisselt of voordat u het elektrisch gereedschap opbergt. Dergelijke preventieve veiligheidsmaatregelen verminderen het risico dat het elektrisch gereedschap per ongeluk opstart.
Nederlands 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. tevens aanraking van de bus na langduring kontinu gebruik. De bus wordt n.l. heet en kan brandwonden veroorzaken. Laat het apparaat nooit zonder belasting braaien bij gebruik van de kruiskoppeling. Als de bus zonder belasting draait, zal de kruiskoppeling de bus heftig heen en weer slingeren. U kunt dan verwond raken, of de bewegig van de bus kan het apparaat zodanig laten trillen, dat u het apparaat laat vallen.
Nederlands WAARSCHUWING Als een elektrisch geleidend vreemd voorwerp in de aansluitpunten van de lithium-ion accu terechtkomt, kan er kortsluiting ontstaan met het risico van brand als gevolg. Let bij het opbergen van de accu op de volgende punten. 䡬 䡬 Plaats geen elektrisch geleidend zaagsel, spijkers, ijzerdraad, koperdraad of andere draad in de opbergdoos.
Nederlands Tabel 1 Aanduidingen van het controlelampje Het controlelampje licht rood op of knippert rood. Voor het laden Knippert Brandt ongeveer 0,5 sekonde. Brandt ongeveer 0,5 sekonde niet. (Uit voor 0,5 seconde) Tijdens opladen Brandt Blift branden Na opladen Knippert Brandt ongeveer 0,5 sekonde. Brandt ongeveer 0,5 sekonde niet. (Uit voor 0,5 sekonde) Opladen onmogelijk Knippert Brandt ongeveer 0,1 sekonde. Brandt ongeveer 0,1 sekonde niet.
Nederlands 2. Kontroleren van de batterij Zorg ervoor dat de batterij stevig geplaatst wordt. Indien dit niet gebeurd, kan het voorkomen dat de accu eruit valt en een ongeluk veroorzaakt. 3. Kiezen van de juiste bus overkomstig de bout Zorg ervoor dat u een bus gebruikt die past op de bout welke moet worden vastgedraaid. Het gebruik van een verkeerde bus zal niet allen resultetren in onvoldoende vastdraaien maar bovendien in beschadigingen aan de bus of moer.
Nederlands VOORZORGSMAATREGELEN BIJ GEBRUIK ONDERHOUD EN INSPECTIE 1. De machine laten rusten na continu werk Na continu vastdraaien van bouten dient u de machine 15 minuten of zo te laten rusten wanneer u de batterij vervangt. De temperatuur van de motor, schakelaar enz. zal flink stijgen als u direct weer begint te werken nadat de batterij vervangen is, hetgeen uiteindelijk kan resulteren in doorbranden van de machine.
Nederlands 7. Opbergen Bewaar de slagmoeraanzetter op een plaats waar de temperatuur niet hoger is dan 40°C, en buiten het bereik van kinderen. OPMERKING: Controleer of de batterij volledig is geladen als deze gedurende langere tijd is opgeslagen (3 maanden of langer). Een batterij met een kleinere capaciteit kan tijdens het gebruik mogelijk niet worden opgeladen als hij langdurig is opgeslagen. 8.
Español (Traducción de las instrucciones originales) ADVERTENCIAS DE SEGURIDAD GENERAL DE LA HERRAMIENTA ELÉCTRICA ADVERTENCIA Lea todas las instrucciones y advertencias de seguridad. Si no se siguen las advertencias e instrucciones, podría producirse una descarga eléctrica, un incendio y/o daños graves. Guarde todas las advertencias e instrucciones para futura referencia.
Español e) Mantenimiento de las herramientas eléctricas. Compruebe si las piezas móviles están mal alineadas o unidas, si hay alguna pieza rota u otra condición que pudiera afectar al funcionamiento de las herramientas eléctricas. Si la herramienta eléctrica está dañada, llévela a reparar antes de utilizarla. Se producen muchos accidentes por no realizar un mantenimiento correcto de las herramientas eléctricas. f) Mantenga las herramientas de corte afiladas y limpias.
Español 13. 14. 15. 16. 17. 18. 19. No dejar que entre suciedad por el orificio de conexión de la batería recargable. Nunca desarmar la batería recargable ni el cargador. Nunca poner en cortocircuito la batería recargable. Poner en cortocircuito a la batería produce una corriente eléctrica enorme y el consecuente recalentamiento, pudiendo quemar o deteriorar la batería. No tirar la batería al fuego. Si se quema la batería puede explotar.
Español ESPECIFICACIONES HERRAMIENTA MOTORIZADA Modelo Tensión Velocidad sin carga Perno ordinario Capacidad Pernos de gran resistencia a la tracción WR18DSHL 18 V 1500 min–1 M12 – M22 M12 – M16 Torsión de apriete (Máxima) 480 N·m Batería recargable BSL1830: Li-ion 18 V (3,0 Ah 10 elementos) Peso 3,4 kg CARGADOR DESMONTAJE E INSTALACIÓN DE LA BATERIA Model UC18YRSL Tensión de carga 14,4 V – 18 V Peso 0,6 kg ACCESORIOS ESTÁNDAR Además de la unidad principal (1), el paquete contiene los acces
Español Tabla 1 Indicaciones de la lámpara piloto El indicador luminoso piloto se ilumina o parpadea en rojo. Antes de la carga Parpadeo Se encenderá durante 0,5 segundos. No se encenderá durante 0,5 segundos. (Apagada durante 0,5 segundos) Durante la carga Iluminación Iluminación permanente Carga completa Parpadeo Se encenderá durante 0,5 segundos. No se encenderá durante 0,5 segundos. (Apagada durante 0,5 segundos) Carga imposible Destello Se encenderá durante 0,1 segundos.
Español 2. Comprobación de la batería Asegúrese de que la batería esté firmemente instalada. Si está floja, puede caerse y provocar accidentes. 3. Selección del recepráculo que concuerde con el perno Cerciorarse de utilizar un receptáculo que concuerde con el perno a ser apretado. Si se utilizase un receptáculo inadecuado, el apriete no será satisfactorio y la cabeza el perno o la tuerca se dañarán.
Español PRECAUCIONES OPERACIONALES 1. Reposo de la herramienta después de un funcionamiento prolongado Tras una tarea de apriete de pernos de larga duración, deje la unidad en reposo durante unos 15 minutos al reemplazar la batería. Si reinicia la tarea inmediatamente después de reemplazar la batería, aumentaría la temperatura del motor, del interruptor, etc., con los consiguientes riesgos de quemadura.
Español 7. Almacenamiento Guarde la llave impacto en un lugar en el cual la temperatura sea inferior a 40°C y esté alejado del alcance de los niños. NOTA: Asegúrese de que la batería está completamente cargada si la va a almacenar durante un prolongado período de tiempo (3 meses o más). Es posible que la batería con una capacidad más pequeña no se pueda cargar cuando se utilice si se ha almacenado durante un prolongado período de tiempo. 8.
Português (Tradução das instruções originais) AVISOS GERAIS DE SEGURANÇA PARA A FERRAMENTA ELÉCTRICA AVISO Leia todas as instruções e avisos de segurança Se não seguir todas as instruções e os avisos, pode provocar um choque eléctrico, incêndio e/ou ferimentos graves. Guarde todos os avisos e instruções para referência futura. O termo “ferramenta eléctrica” em todos os avisos referese à sua ferramenta ligada à corrente (com fios) ou à ferramenta eléctrica a baterias (sem fios).
Português f) Mantenha as ferramentas de corte afiadas e limpas. As ferramentas de corte com uma manutenção adequada e extremidades afiadas são menos propensas a dobrar e mais fáceis de controlar. g) Utilize a ferramenta eléctrica, acessórios e pontas de ferramentas, etc., de acordo com estas instruções, tomando em consideração as condições de trabalho e o trabalho a ser efectuado. A utilização de uma ferramenta eléctrica para operações diferentes das concebidas pode resultar num mau funcionamento.
Português 18. 19. Leve a bateria à loja onde você a comprou assim que a vida útil da bateria após a recarga começar a ficar muito curta para uso prático. Não descarte a bateria velha. O uso de uma bateria velha pode danificar o recarregador. PRECAUÇÕES PARA A BATERIA DE IÕES DE LÍTIO Para aumentar a vida útil, a bateria de iões de lítio está equipada com uma função de protecção para impedir a transmissão de corrente.
Português RECARREGADOR APLICAÇÕES Modelo UC18YRSL Voltagem para recarga Apertos e desapertos de todos os tipos de parafusos e porcas, usado para prender materiais estruturais. 14,4 V – 18 V Peso 0,6 kg RETIRADA/INSTALAÇÃO DA BATERIA ACESSÓRIOS-PADRÃO Além da unidade principal (1), o conjunto inclui os acessórios indicados na tabela abaixo. 1 Recarregador .................................... 1 WR18DSHL 2 Bateria ............................................... 2 (2LSRK) 3 Estojo de plástico .........
Português (2) Quanto a temperaturas da bateria recarregável As temperaturas aplicáveis às baterias recarregáveis estão indicadas na Quadro 2; as baterias que tenham aquecido devem ser deixadas a arrefecer durante algum tempo antes de serem recarregadas.
Português MODO DE USAR 1. Utilização do interruptor O interruptor desta máquina funciona como interruptor do motor e como selector da direcção da rotação. Quando o interruptor está colocado na posição R indicada no punho, o motor roda no sentido horário para apertas o parafuso. Quando o interruptor está colocado na posição L , o motor roda no sentido anti-horário para desapertar o parafuso. Quando o interruptor é libertado, o motor pára. (Fig.
Português (4) Condições de aperto O torque de aperto difere segundo a proporção do torque, a classe e o comprimento dos parafusos mesmo quando se utilizam aqueles que possuem roscas do mesmo tamanho. O torque de aperto também difere de acordo com a condição da superfície da peça através da qual o parafuso são apertados. Quando um parafuso e uma porca giram juntos, o torque é grandemente reduzido.
Português GARANTIA Garantimos que a Hitachi Power Tools obedece às respectivas normas específicas estatutárias/de país. Esta garantia não cobre avarias ou danos derivados de má utilização, abuso ou desgaste normal. Em caso de queixa, envie a Ferramenta, não desmontada, juntamente com o CERTIFICADO DE GARANTIA que se encontra no fundo destas instruções de utilização, para um Centro de Serviço Autorizado Hitachi.
08Back_WR18DSHL_WE 61 3/23/11, 11:35 Item Part Name Q’TY No. 1 FRONT CAP 1 TAPPING SCREW (W/SP. WASHER) 4 2 D5×35 3 HAMMER CASE 1 4 PIN RETAINER (B) 1 5 PLUNGER (B) 1 6 ANVIL (C) 1 7 STEEL BALL D6.35 2 8 HAMMER 1 9 STEEL BALL D3.
08Back_WR18DSHL_WE 62 12/14/10, 8:44
English Nederlands GARANTIEBEWIJS GUARANTEE CERTIFICATE 1 2 3 4 5 Model No. Serial No. Date of Purchase Customer Name and Address Dealer Name and Address (Please stamp dealer name and address) Deutsch 1 2 3 4 5 Español CERTIFICADO DE GARANTIA GARANTIESCHEIN 1 2 3 4 5 Modell-Nr. Serien-Nr.
1 2 3 4 ✄ 5 64 08Back_WR18DSHL_WE 64 12/14/10, 8:44
Hitachi Power Tools Europe GmbH Siemensring 34, 47877 willich 1, F. R. Germany Tel: +49 2154 49930 Fax: +49 2154 499350 URL: http://www.hitachi-powertools.de Hitachi Power Tools Netherlands B. V. Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040 Fax: +31 30 6067266 URL: http://www.hitachi-powertools.nl Hitachi Power Tools (U. K.) Ltd. Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom Tel: +44 1908 660663 Fax: +44 1908 606642 URL: http://www.hitachi-powertools.co.
08Back_WR18DSHL_WE 66 12/14/10, 8:44
08Back_WR18DSHL_WE 67 10/9/12, 13:36
Nederlands English EC DECLARATION OF CONFORMITY EC VERKLARING VAN CONFORMITEIT We declare under our sole responsibility that this product is in conformity with standards or standardization documents EN60745, EN60335, EN55014 and EN61000 in accordance with Directives 2004/108/EC, 2006/95/EC and 2006/42/EC. This product also conforms to RoHS Directive 2011/65/EU. The European Standards Manager at Hitachi Koki Europe Ltd. is authorized to compile the technical file.