HITACHI VIDEO CASSETTE RECORDER VT-FX631A-VT-FX632A Owner's manual This instruction manual includes instructions on the use of both VT-FX631A and VT-FX632A. Using these quality features: • Common for VT-FX631A and VT-FX632A • The VCR Plus+* programming system allows you to program the VCR for timer recording by simply entering a PlusCode* number. * VCR Plus+ and Pluscode are trademarks of Gemstar Development Corporation. VCR Plus+ system is manufactured under license from Gemstar Development Corporation.
TABLE OF CONTENTS FOR YOUR SAFETY .................................................................................................................. IMPORTANT SAFEGUARDS ..................................................................................................... CUSTOMER CONTROLS .......................................................................................................... VCR Customer Controls .............................................................................................
SPECIAL PLAYBACK EFFECTS ............................................................................................. 32 USING THE "SUPER INDEX" FEATURE................................................................................. 36 VIEWING THE ON-SCREEN DISPLAY ................................................................................... 39 INDEXING WITH THE TIME COUNTER.................................................................................. 39 RECORDING A PROGRAM......................
INSERT.
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 8 Ventilation -- Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the video product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug or other similar surface.
16 Lightning -- For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable-system. This will prevent damage to the video product due to lightning and power-line surges. SERVICE 17 Servicing -- Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards.
VCR Front Panel Controls VCR Display Panel 1 POWER button 2 Infrared receiver 3 Cassette compartment 4 STOP/EJECT button 5 PLAY button F.
_.ccessories supplied Check and indentify the accessories supplied. If any are missing or appear damaged, consult your dealer. Cable for connecting this VCR to a TV Batteries for remote control handset (R6) VCR Rear Panel 1._.9.9 2._0 2"1 2._22 2._33 24 AUDIO IN LTR jacks VIDEO IN jack IN FROM ANT.
14 15 16 17 18 19 20 21 22 VCR, TV, CATV - Device buttons let you set the remote to control one of the three devices. VCR/TV mode select button CH (channel up!down) button PAUSE button F.FWD button - fast forward or search PLAY button - playback SUPER INDEX - to use the SUPER INDEX function Number buttons AVX button - select L The remote control requires two "AA" batteries. 1 Insert your fingertip into the notch and push the battery compartment lid to remove it.
3 Replace the lid. 1 Make sure there is no obstacle between the remote control and VCR's infrared receiver. Infrared Receiver Note: yo u Cannot operate the VCR if there is an obstacle (for exarnp!el coffee table, sofa, etc) between the VCR and remote contro. 2 Point the remote control at the VCR's infrared receiver and press the required button on the remote control. Only use video cassettes with the _ mark in this VCR. The table shows the recording time of different cassettes.
• To get the best quality picture record at standard recording speed (SP) • This VCR does not record at the LP speed, but it can play cassette that were recorded at the LP speed. • Safety tabs prevent erasure The VCR automatically enters the playback mode when a cassette without its safety tab is inserted. The VCR won't record on a tape without a safety tab and the cassette will be ejected if the REC or REC/IRT button is pressed. Be sure to check the safety tab before inserting a cassette.
YOU CAN... • WATCH AVAILABLE TV CHANNELS • RECORD AND WATCH THE SAME CHANNEL • RECORD ONE CHANNEL AND WATCH ANOTHER Hoo<-J_ A I,,Jstra;,on TABLE A SeleG_ and Wat_ _a_nels using TV Select and Wat¢h Chsnnels u_ng VCR R_ord and Watch the Seine Chanr_L Se|_ OFF (TV mode] Chsn_ to Wa_ 30f4 S_ Charms[t= W_.
OFF YOU CAN... • WATCH AVAILABLE CABLE CHANNELS RECORD AND WATCH THE SAME CHANNEL RECORD ONE CHANNEL AND WATCH ANOTHER Hookup C IHus_ration TAgL_ C 3ot4 Switch the RF Channel When the VCR ,s on i:s video signal can come into your TV on e,mer channe_ 3 or channe_4 You need _o select :he appropr,a:e channel. • When the power is :Jmed on press the POWER bJ:ton to :Jrn ,t off. Press :he PLAY button on front of me VCR.
(channel 4) in _ne VCR's d,splay D,splay _he channel wh,cn ,s no_ Jsed by a cor_r_ercia_ channel ,n your area. YOU CAN... • WATCH AVAILABLE CABLE CHANNELS • RECORD AND WATCH THE SAME CHANNEL • RECORD ONE CHANNEL AND WATCH ANOTHER Hookup D IHus_ration AMX cr VI_EO _;o_ Se_,_ Ch_c_nel ' Wa_ Pt_b_ _ • Tape Ci_nae_to R_.o_ OFF AU× er _13,_ YOU CAN... • WATCH AVAILABLE CABLE CHANNELS • RECORD AND WATCH THE SAME CHANNEL YOU CAN'T...
Switch the RF Channel When the VCR is on, its video signal can come into your TV on either channel 3 or channel 4, You need to select the appropriate channel. - When the power is turned on, press the POWER button to turn it off. Press the PLAY button on front of the VCR. Pressing the CHANNEL _ button a/terantes between RFCH-03 (channel 3) and RFCH-04 (channel 4) in the VCR's display, Display the channel which is not used by a commercial channel in your area. YOU CAN...
YOU CAN_.
goes out t'or move [han I hmtr, W_en you first phzg ]_ the VCR or after a power outage, [he clock display _i]] read "--:--', Methods for setting the clock installed with these VCR's For VT-FX632A use method A or B. For VT-FX631A use method B. Automatic mode See pages 17-19. ]he following is the method for setting the clock with auto clock set function.
1 Turn on the TV and select the video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the TV to AUX or VIDEO. 2 Press the GUIDE button, The main on-screen menu wi]]appear on the TV screen. You may view all the on-screen instructions in English, French, or Spanish, When you first set up your VCR, it wi]] be set to English, Press the (8) button for French or the (9) button for Spanish, Remote Control Illustration.
4 Make sure that item t is highlighted "CLOCK SET ". - If "CLOCK SET " is highlighted, press the (1) button to switch it to "CLOCK SET < AUTO >" . i5 Press the (2) button. This screen appears to show that the clock is being set. - It may take about five minutes.
1 Press the GUIDE button, The main on-screen menu wi//appear on the TV screen. Remote Control Illustration 2 Press the (3) button to bring up the "CLOCK SET" menu, Make sure that item 1 is highlighted "CLOCK SET ". 3 Press the (3) button to select your local time zone, Each time (3) is pressed, the option for "SET TIME ZONE" switches from to , , , , , , and back to .
5 Press the (2) button to set the time. This screen appears to show that the clock is being set. 1 Press the GUIDE button. The main on-screen menu will appear on the TV screen. You may view all the on-screen instructions in English, French, or Spanish. When you first set up your VCR, it will be set to English. Press the (8) button for French or the (9) button for Spanish. Remote Control Illustration iiiiiiiiiiiiiiiiiiiii ___tiiiiiiiiii 2 Press the (3) button.
VT-FX632A ONLY 3 Press the (1) button to select "CLOCK SET ". When "CLOCK SET " is selected. "SET TIME ZONE" (item 3) and "SET DST" (item 4) are not displayed. VT-FX632A ONLY 4 Press the (2) button to bring up the clock set menu. • The white dash "-, appea_ for the item to be change d on the screen as you proceed. Common for VT-FX631A and VT-FX632A 5 Press the number buttons to fill the hour and minutes.
7 Press the number buttons to fill in the number of the month, then the day then the year. • For dates with only one number (1-9) press the (0) button first, then the date. For example, if today is July 8 "1997, press (0)(7)(0)(8)(9)(7). The correct day of the week will appear by itself. 8 Press the GUIDE button. The VCR clock is now set, and should show the correct time of day on the VCR's display. 1 Press the POWER button to turn on the VCR.
2 Turn on the TV and select the video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the "iV to AUX or VIDEO. 3 Press the GUIDE button. The main on-screen menu will appear on the TV screen. Remote Control Illustration. 4 Press the (4) button to select the CHANNEL PRESET operation.
7 Press GUIDE to return to regular viewing. • When automatic . presetting of channels are finished Press the CH (channel) button (or numbered you can receive. buttons) to check the channels When your VCR is receiving a channel caption signal that is transmitted by a local broadcasting station together with a TV program, a station identifier is d splayed on the 3_Vscreen. i ...............................
1 Press the GUIDE button. The main on-screen menu w_ll appear on the TV screen. 2 Press the (4) button to select the CHANNEL PRESET operation. Remote Control Illustration. 3 Press the (3) button to select "ADD/ERASE CHANNEL". 4 Use the number buttons to select the number of the channel you want to add or erase. 5 Press the STOP button to delete the channel, or press the PLAY button to add it. 6 Press the GUIDE button to return to regular viewing.
1 Turn on the TV and select the video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the TV to AUX or VIDEO im "__ _ _, 2 Press the GUIDE button. The mare on-screen menu w_llappear on the TV screen 3 Press the (2) button to select "VCR SETUP". Remote Control Illustration 4 Press the (1) button to select AUTO BLUE "ON" or"OFF".
5 Press the GUIDE button to end the setting. The following setup allows the VCR channel to automatically switch to the cable box output channel during delayed recording. 1 Turn on the TV and select the video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the "iV to AUX or VIDEO. 2 Press the GUIDE button. The main on-screen menu will appear on the TV screen. 3 Press the (4) button to select the CHANNEL PRESET operation. Remote Control Illustration.
5 Press the (5) button to select "CABLE BOX SETUP" menu. 6 Press the (1) button to answer ,'YES,! to the question "is A CABLE BOX BEING USED?" • If you select "YES", you need not operate 'VCR PLUS =1" SETUP II ( see page 48). During delayed recording, the VCR channel will automatically switch to the cable box output channel. 7 Using the VCR remote, enter the cable box output channel numbers. For example, press (0)(3) for channel 3. 8 Press the GUIDE button to enter the output channel of your cable box.
Remote Control Illustration. 9 Press the GUIDE button to end this setting. he cable box output channel has now been set. However, the VCR does not control your cable box. Turn n the cable box and leave it tuned to the channel you want to record before the recording is scheduled begin. NOte_ !f y_ _ ma_ e am ista_e w he n e _terin g d!gits i P_eS_h e C EEARb Utton _e_eat _/y t0 ret_n_h e whi_e d ash i!_!i 1 Turn on the TV and select the video channel (3 or 4).
Remote Control Illustration. 4 Press the STOP button to end playback. When the video cassette reaches the end of the tape, the VCR will stop automatically and automatically rewind the tape. • If you press the POWER button while the tape is rewinding, the power will not shut off until the tape has been completely rewound. You may also rewind the tape manually at any time. Manual Rewind 1 Press the STOP button to end playback. iiiii_iii_ Remote Control Illustration• 2 Press the REW button.
Press the REW or F.FWD button, then press it again. To stop the tape, press the STOP button. Remote Control Illustration. Auto Tracking Pressing the PLAY button starts the auto tracking feature, which automatically adjusts playback to eliminate static lines or picture noise that may appear on the screen. Manual Tracking Scratched tapes or poorly recorded tapes may require additional picture adjustment. You can do this with the remote control. Remote Control Illustration. Press the CH (;_ cassette.
The picture will "freeze". You may see some minor noise or interference on the screen. This is normal. • To resume play, press the PLAY button or PAUSE button again. If you press the DISP button when viewing a video cassette, the display, as shown, appears for several seconds so you can see the functions of the number buttons on the remote control. Number (6) button: Frame advance • The above function always work when you are viewing a video cassette even if the display, as shown, is not displayed.
Slow motion 1 Press the PLAY button. Remote Control Illustration. 2 Press the SLOW button to slow the playback speed. 3 Press the PLAY button to return to play back at normal speed. iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii Press the STOP button to stop the tape. Visual Search This function let you search backward and forward through the videotape while viewing it. Remote Control Illustration.
During play: Press the REW button to search in reverse. Press the F.FWD button to search ahead. • Press the PLAY button to return to normal playback. Press REW or F.FWD and hold it; you can search backward or forward through the tape at a higher speed while viewing it. • Press PLAY and REW, then hold REW for backward search at a higher speed. • Press PLAY and F.FWD, then hold F.FWD for forward search at a higher speed. • Release REW or F.FWD to return to normal playback.
4 Press the GUIDE button to end the setting. • What is SUPER INDEX SUPER INDEX allows you to quickly search for a program or a scene you want to view or the point from which you want to start recording on tape, with the following four functions: • INDEX SEARCH: You can locate the beginning of a recorded program, using the INDEX feature*. • Each time you press the REC or REC/IRT button to start recording, the VCR will record an INDEX mark at the start of recording.
• Locating the beginning of a blank section (BLANK SEARCH) This function searches for a non-recorded section of remaining tape, or unused tape, and stops the tape when it locates such a section.
When the beginning of blank is located, the STOP screen will appear for five seconds and the tape will stop • The tape remaining time appears in the VCR display. • Switching rewind or fast forward to visual search (EASY VIEW) Hold down the (VIEW/SKIP/BLANK) button during rewind (or fast forward), and the mode will switch to visual search, so that you can search for a scene you want to view while scanning pictures.
Remote Control Illustration. = Switching between the clock, time counter and time of remaining tape Press DISP while the on-screen display is displayed. The on-screen display switches in the order below together with the VCR's display. Press the DISP button to see the clock. Remote Control Illustration. Press the DISP button a second time to see just the time counter. On-screen Display Illustration ...................................
1 Press the DISP button two or three times. The counter will appear in the VCR's display. Remote Control Illustration. 2 Begin recording or playing back a tape. 3 At the point that you want to go back to, press the CLEAR button. This resets the counter to 0:00:00. 4 ]_:ess the STOP button when you are done l_eording o1:playing back the tape. 5 Press the REW button to rewind the tape. It will automatically stop at the spot where you cleared the counter in step 3.
• Before you record The VCR must be hooked up properly for recording. See the Simple Hookups at the beginning of this manual. Copyright infringement warning Most television programs and films are copyrighted. This means that someone has legal rights governing the reproduction and distribution of this matedal. In certain circumstances, copyright law may apply to private in-home taping of copyrighted materials. In most cases, it is okay to record for personal use, as long as you do not sell the material.
Remote Control Illustration. 4 Press the CH (_/Y) button or the number buttons to select the channel you want to record. for the longest recording time on a single tape). Example: Select channel 8. • 100lENT and (2) and (4) for the channel 124. Remote Control Illustration. 5 Press the REC button on the remote control or the REC/IRT button on the VCR. Recording will start and the REC indictor on the VCR will appear.
iii iiiiiiiiiiiiiiiiiiiiiiiiiiiii • To watch one program while recording another 1 Once you have set the VCR for recording, press the VCRiTV button. The VCR indicator disappears. Now, you will be viewing through your TV only. 2 Switch channels using your TV controls or the VCR remote, if it's programmed to control your TV (see page 54). Remote Control Illustration.
3 Press the PAUSE button to continue recording. Automatic Indexing Your VCR will automatically create an invisible "INDEX" mark every time you press the REC button while recording. During playback, the Index Search feature will let you move through a tape that has several recordings on it by searching for the "INDEX" mark. See Page 34, "Locating the beginning of a recorded program ( INDEX SEARCH)".
4 Press the (5) button to set the STEREO/MONO option to "STEREO". 5 Press the GUIDE button to end the setting. 6 Follow the Step 1 through 6 on "Basic Recording Steps" on pages 39 and 40. • Stereo vs. mono sound When you select the STEREO option in the initial setup operation, your VCR records in stereo any station that broadcasts stereo sounds. When a TV channel broadcasts in stereo, you'll see a stereo indicator on the TV screen. Set to MONO if the stereo signal is weak and the sound is too "noisy". .
2 Press the REC/IRT button twice to indicate the recording time on the display. • You may increase the recording time by 30 minutes each time you press the REC/IRT button. • While you are recording, the remaining recording time is shown on the VCR display. • At the end of your recording, the display will read "0:00", recording will stop automatically, and the VCR will turn itself off. Instant Recording Illustretion. To stop recording while in the IRT mode: 1 Press the STOP button within 10 seconds.
Delayed Recording Steps You set up the delayed recording using the on-screen Easy Guide System. 1 Insert blank or erasable tape. The power comes on automatically and the tape indicator lights on the display. • If a cassette without its safety tab is inserted, playback starts automatically and timed record won't operate. 2 Turn on the TV and select the video channel (3 or 4). Or, if you are hooked up with an audio/video cable, set the "iV to AUX or VIDEO. Remote Control Illustration.
DAILY Records a show at the same time every day of the week, Monday through Friday. WEEKLY Records a show at the same day and time every week. EXAMPLE: Set the VCR to record "one time", a program on Channel 8 that starts at 6:00 PM and ends at 6:30 PM on 7/10/98, at the EP recording speed. 4 Press the (1) button to bring up the screen for One Time Recording • If you have installed a cable box (see page 26), the cable box output channel will appear in the CH column Remote Control Illustration.
Remote Control Illustration. 7 Press the (2) button for PM. 8 Enter the end time by pressing (0), (6), (3) and (0) for 6:30. The VCR automatically selects PM for you. 9 Enter the recording date by pressing (0), (7), (1) and (0) for 7/10/98. Remote Control Illustration. 10 Press the TAPE SPEED button to select the recording speed EP.
11 Press the PROGRAM button to set the program in memory. 12 Press the POWER button to turn off the VCR. The delayed recording indicator will display on the VCR. This tells you that the VCR will automatically record at the times and dates you have programmed. When you have set up all the timed recordings you want: • Don't forget to load a videocassette (with the safety tab still attached) to record on.
• About the VCR Plus+ system This handy feature makes timed recording a snap. You don't need to enter the specific channel, date, time or duration of a program. All you enter is its PlusCode programming number - a number of up to eight digits. This special code is easy to find in your favodte TV program guide or daily newspaper. Here's a sample page from TV Guide showing PlusCode numbers next to each program. Your local channels may be different from the VCR Plus+ channel codes.
!!_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i _ i,_ ,_ !i!_,:i_ ,i ,!,i!ii_ii_,_,',_il I, ,_i:,:ii,!:iiii:_:iiiiiiil,i_,,, i!iiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiii i iiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiii _i_i_i_i_i_ii_i_i_i_i_i_i_i_i_i' iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii Note in the example that
3 Press the (4) button to select CHANNEL PRESET. Note: If you have set up the cable box, the follo_4ng opera_ion is not necessa12_. 4 Press the (4) button to select VCR PLUS+ SETUP. A small arrow points to a blank "--" in the CHANNEL column. 5 Press the CH (i/Y) button to move up and down through the channel list until you reach VCR Plus+ CH42. 6 Press the number buttons to assign your broadcast channel number to the corresponding VCR Plus+ channel.
8 Press the GUIDE button to end the setup procedure. You are ready to begin delayed recording with the VCR pluls+ system. Remote Control Illustration. • Using the VCR Plus+ system to record a program screen) (by using TV 1 Insert a blank or erasable tape. The power comes on automatically and the tape indicator lights on the display. • When a cassette without its safety tab is inserted, playback starts automatically and VCR Plus+ recording won't operate.
4 Press the PROGRAM button to store the PlusCode number in the VCR's memory. Types of Delayed Recordings ONE TIME Records one show at a particular date and time. DAILY Records a show at the same time every day of the week, Monday throught Friday. WEEKLY Records a show at the same day and time every week.
play) or EP (extended play). The screen will display all the details of the program you chose. Check the CH number to make sure it is the right one. If not, you need to check your VCR Plus+ channel setup again.
Using the VCR Plus+ system to record a program (by using the VCWs display) You can use the VCR Plus+ system to program the timer, observing the VCR's display, without turning on the power to the VCR and TV. Remote Control Illustration 1 Insert a blank or eraseable tape. The power comes on automatically and the tape indicator lights on the display. • When a cassette without its safety tab is inserted, playback starts automatically and VCR Plus+ recording won't operate.
4 Press the number buttons to enter the PlusCode number of the program you want to record. COrrect on e 5 Press the number buttons to enter the PlusCode number in the VCR's memory. The start time and channel will appear. Check the details of the program. • If you have installed a cable box (see page 26), the cable box output channel will appear in the channel display • If "Err" flashes for about five seconds, check the PlusCode number of the program and enter it again.
Important: Your timed recording settings take effect when you turn off the power on the VCR. Caution 0f VCRPI Aft e re nt eri ng aP!u s c 0 den um be_iCh eCk the in f0 _ma_io n displayed wi_h the_!P R OG RAM REVI EW'_ff h_ _ei_ (a re)_ hY _ _ _ _ Ss_ p_0g_am(s)i p!e _se c_n c e!o _ _0 _re_t !t(t h_m) i P!_as_ rere _0 Page5 3i '_Rev!ew! _ g wha_ Y0 U haV_ PrOgram _ ed To go into the recording mode: 1. Press the POWER button to turn the VCR on. 2, Turn on "IV and select the video channel (3 or 4).
4 Press the GUIDE button to end. The VCR remote control can be programmed to control many TV brands that are remote controlled. 1 Turn on the TV. 2 Point VCR remote control toward TV. 3 Press and hold the "TV" button. Remote Control Illustration. 4 Press the remote button corresponding to your TV brand as shown in the set-up chart. The TV channel will change to confirm that the remote control has been set.
Hitachi 1 Gold star 1 6 Panasonic 1 CH Zenith 2 Toshiba 7 Miteubishi Sony 3 Gold star 2 8 JVC 100lENT Magnavox 4 Panasonie 2 9 Sharp 1 VOL (UP) Sanyo 5 RCA 0 Sharp 2 AVX CH • Using the VCR remote to control your TV 1 Press the "TV" button on remote control. Remote Control Illustration. 2 Point VCR remote control toward TV. 3 Press buttons corresponding to the functions available on your TV remote control.
3. Press and hold the "CATV" button. 4 Press the number button corresponding to your cable box a shown in the set-up chart. The cable box channel will change to confirm that the remote control has been set Jerrold 1 1 Zenith 5 Jerrold 2 2 Scientific Atlanta 6 Jerrold 3 3 Pioneer 7 Hamlin 4 Philips 8 Notei !f your cable bbx iS nbt listed on the Set_U >Cha_;tryal!thebu_o_S!!stedi_thecha_unti!the rem0_efo_you_ab!e b0x • Using the VCR remote to control your cable box.
• Hookup When your VCR is connected to a stereo system, you can: • Make high quality "audio only" recordings for up to 6 hours (on a T-120 video cassette tape). • Receive quality stereo sound from your VCR through your stereo system. • Use the VCR as an extra audio tape deck for dubbing. Hook-up Illustration. • To record from stereo BEFORE YOU BEGIN... Remote Control Illustration. • Make sure the VCR is connected to your stereo system, as shown above.
• Hook-up You may use your VCR to copy tapes from any camcorder onto standard VHS cassette ............. tapes:......................................................................................................... he backof the VCR * It is not necassary to connect the S-VIDEO jack Camcorder Hook-up Illustration. • To copy from a camcorder BEFORE YOU BEGIN... Connect the camcorder's AV output cable to the audio/video on the back of your VCR.
3 Press the PLAY button on the camcorder. You will see the camcorder tape being played on the TV. 4 When you see the part of the Camcorder tape you wish to copy, press the PAUSE button again to release pause and start copying the camcorder tape. • Press the STOP button to finish recording. • Hookup If you have two VCRs, you may use one VCR to record a tape that is being played back in the other VCR.
3 Press the PLAY button on VCR-2. You will see the taped program being played on the TV. 4 When you see the part of the program you wish to record, press the PAUSE button on VCR-1 again to release pause and start recording. • Press the STOP button to finish recording. • Problem guide No power Remote control doesn't work Won't record Won't play back Won't make timer recordings • Make sure the VCR is plugged into an AC outlet. • Make sure the batteries are fresh, and properly installed.
Snowy picture in playback • Snow or picture noise is normal during search, still, and slow Playback. • Head cleaning may be required. • Tape is worn or of inferior quality - adjust tracking controls. Snowy picture in normal -I'V viewing • Check antenna or cable connections. Clock • Power has been interrupted - reset the clock. • Reset the clock. shows --:-- Erratic VCR display • Push the reset switch with a sharp pointed instrument (pen, toothpick, etc.).
!!:: When programming the timer. • Eight programs have already been stored. Cancel unnecessary program and transfer the new programming. When you turn power off after programming the timer, or transfer the programming with power off. • A cassette has not been inserted or a cassette without safety tab has been inserted. A cassette without safety tab will be ejected automatically. Insert a cassette with safety tab intact. When you press the play, record, fast forward, rewind or super index button.
Type: Power Input: Power Consumption: Cabinet Size: Auto programming frequency synthesis AC 120V 60 Hz 20W nominal 14-15/16" (W) x 3-11/16" (H) x 10-13/16" (D) 36.0 cm ON) x 9.3 cm (H) x 27.6 cm (D) Weight: 7.7 Ibs. (3.6 kg) -4°F to 131°F Storage Temperature: 41°F to 104°F Operating Temperature: Accessories: 1 coaxial cable (Part No. EW10251) 1 remote control unit (Part No. HL10991), 2 AA batteries * Check your cable company's compatibility requirements.