Model Modèle Modelo UC 18YRL • UC 18YFL Battery Charger Chargeur de batterie Cargador de baterías SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this battery charger can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the battery charger.
English CONTENTS Page IMPORTANT SAFETY INFORMATION ............. 3 MEANINGS OF SIGNAL WORDS ..................... 3 SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER .......................... 4 IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER ................................... 5 DISPOSAL OF THE EXHAUSTED BATTERY .... 6 Français TABLE DES MATIERES Page INFORMATIONS IMPORTANTES DE SÉCURITÉ ...................................................
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this battery charger. Most accidents that result from battery charger operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER WARNING: Death or serious bodily injury could result from improper or unsafe use of battery chargers. To avoid these risks, follow these basic safety instructions: READ ALL INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. This manual contains important safety and operating instructions for battery charger Model UC18YRL and UC18YFL.
English * If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing the wattage rating by the voltage rating–for example: 1, 250watts = 10 amperes 125 volts 9. Do not operate battery charger with damaged cord or plug-replace them immediately. 10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11.
English 12. ALWAYS operate charger on standard household electrical power (120 volts). Using the charger on any other voltage may overheat and damage the charger. 13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger. 14. ALWAYS disconnect the power cord from its receptacle when the charger is not in use. DISPOSAL OF THE EXHAUSTED BATTERY WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated.
English OPERATION AND MAINTENANCE NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the battery charger. NEVER operate, or attempt any maintenance on the battery charger unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own battery charger.
English SPECIFICATIONS Model UC18YRL / UC18YFL Input power source Single phase: AC 120 V, 60 Hz Charging time Approx. 20 minutes .......... EB712S, EB7S, EB714S, FEB7S, EB912S, EB9S, EB914S, EB914, FEB9S, EB1212S, EB12S, EB1214S, EB1214L, FEB12S, EB1412S, EB1414S, EB1414, EB1812S, EB1814SL Approx. 30 minutes .......... EB7B, EB9B, EB12B, EB1220BL, EB14B, EB18B EB1820, EB1820L Approx. 35 minutes .......... EB924, EB1224, EB1424, EB1824L Approx. 40 minutes ..........
English 1. Insert the plug of battery charger into the receptacle. When the plug of battery charger has been inserted into the receptacle, pilot lamp will blink in red. (At 1-second intervals) WARNING: Do not use the electrical cord if damaged. Have it repaired immediately. 2. Insert the battery to the battery charger. Insert the battery into the battery charger as shown in Fig. 2. Make sure it contacts the bottom of the battery charger.
English Table 2 Before Charge charging status lamp (RED) While charging Charging complete Overheat lamp (GREEN) Blinks (RED) Indications of the pilot lamp Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Lights (RED) Lights continuously Blinks (RED) Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Charging impossible Flickers (RED) Lights for 0.1 seconds. Does not light for 0.1 seconds. (off for 0.
English 䡬 Regarding recharging time Table 4 shows the recharging time required according to the type of battery. Table 4 Recharging time (approx. min.) at 20°C Battery capacity (Ah) Ni-Cd BATTERY Battery Li-ion BATTERY Ni-MH BATTERY Voltage 1.2–1.4 Ah 7.2V 9.6V 12V 14.4V 18V EB712S EB7S EB714S FEB7S EB912S EB914S EB9S EB914 FEB9S EB12S EB1212S EB1214S EB1214L FEB12S EB1412S EB1414S EB1414 2.0 Ah 2.4 Ah 2.6 Ah 3.0 Ah 3.3 Ah 3.0 Ah 20min. EB7B 30min. ––––––––––––– 35min.
English How to make the batteries perform longer. 䡬 䡬 Recharge the batteries before they become completely exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after use.
English 3. Service parts list CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir ce chargeur de batterie. La plupart des accidents causés lors de l’utilisation ou de l’entretien du chargeur de batterie proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE CONSIGNES DE SÉCURITÉ IMPORTANTES POUR LE CHARGEUR DE BATTERIE AVERTISSEMENT: Une utilisation incorrecte ou dangereuse des chargeurs de batterie peut entraîner la mort ou des blessures graves. LIRE TOUT CE MODE D'EMPLOI. 1. 2. 3. 4. 5. 6. 7. 8. Ce manuel renferme des consignes de sécurité et d’utilisation importantes pour le chargeur de batterie modèle UC18YRL et UC18YFL.
Français TABLEAU 1 CALIBRE MINIMUM RECOMMANDÉ POUR LES CORDONS DE RALLONGE DES CHARGEURS DE BATTERIE Intensité nominale d’entrée CA (ampères)* Egal ou supérieur à mais non inférieur à 0 2 3 2 3 4 * Calibre du cordon Longueur de cordon en pieds (mètres) 25 (7,5) 50 (15) 100 (30) 150 (45) 18 18 18 18 18 18 18 16 16 16 14 14 Si l’intensité nominale d’entrée du chargeur de batterie est donnée en watts et non en ampères, calculer la capacité en ampères correspondante en divisant la capacité en ampères p
Français 3. 4. NE JAMAIS NE JAMAIS 5. NE JAMAIS 6. NE JAMAIS 7. 8. NE JAMAIS NE JAMAIS 9. NE JAMAIS 10. NE JAMAIS 11. NE JAMAIS 12. TOUJOURS 13. TOUJOURS 14. TOUJOURS court-circuiter la batterie. insérer d’objets dans les ouïes d’aération du chargeur. Il pourrait en résulter un choc électrique ou des dommages du chargeur. effectuer la recharge à l’extérieur. Eloigner la batterie des rayons directs du soleil et utiliser exclusivement dans des endroits à faible humidité et bien aérés.
Français UTILISATION ET ENTRETIEN REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien du chargeur de batterie. NE JAMAIS utiliser ni entreprendre une révision du chargeur de batterie sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux du chargeur de batterie.
Français SPECIFICATIONS Modèle UC18YRL / UC18YFL Source d’alimentation d’entrée Monophasée: CA 120 V, 60 Hz Durée de recharge Environ 20 minutes .......... EB712S, EB7S, EB714S, FEB7S, EB912S, EB9S, EB914S, EB914, FEB9S, EB1212S, EB12S, EB1214S, EB1214L, FEB12S, EB1412S, EB1414S, EB1414, EB1812S, EB1814SL Environ 30 minutes .......... EB7B, EB9B, EB12B, EB1220BL, EB14B, EB18B EB1820, EB1820L Environ 35 minutes .......... EB924, EB1224, EB1424, EB1824L Environ 40 minutes ..........
Français 1. Brancher la fiche du chargeur de batterie dans la prise. Quand la fiche du chargeur de batterie est branchée dans la prise, le voyant de recharge clignote lentement en rouge. (A intervalles d’une seconde) AVERTISSEMENT: Ne pas utiliser le cordon électrique s’il est endommagé. Le immédiatement. faire réparer 2. Insérer la batterie dans le chargeur de batterie. Insérer la batterie dans le chargeur de batterie comme indiqué à la Fig. 2.
Français Tableau 2 Voyant d’état de charge (rouge) Avant la recharge Indications de la lampe témoin Clignote S’allume pendant 0,5 seconde. (ROUGE) Ne s’allume pas pendant 0,5 seconde. (Eteint pendant 0,5 seconde) Pendant la recharge S’allume S’allume sans interruption (ROUGE) Recharge terminée Clignote S’allume pendant 0,5 seconde. (ROUGE) Ne s’allume pas pendant 0,5 seconde. (Eteint pendant 0,5 seconde) Scintille S’allume pendant 0,1 seconde.
Français 䡬 Durée de recharge Le Tableau 4 montre le temps de recharge nécessaire en fonction du type de batterie. Tableau 4 Temps de recharge (en minutes approx.) à 20°C Capacité de la batterie (Ah) Tension de la batterie 7.2V 9.6V 12V 14.4V 18V BATTERIE Ni-Cd 1.2–1.4 Ah EB712S EB7S EB714S FEB7S EB912S EB914S EB9S EB914 FEB9S EB12S EB1212S EB1214S EB1214L FEB12S EB1412S EB1414S EB1414 2.0 Ah BATTERIE Li-ion BATTERIE Ni-MH 2.4 Ah 2.6 Ah 3.0 Ah 3.3 Ah 3.0 Ah 20min. EB7B 30min.
Français phénomène est temporaire et le temps de recharge normal sera rétabli quand les batteries auront été rechargées 2 ou 3 fois. Comment prolonger la durée de vie des batteries 䡬 䡬 Recharger les batteries avant qu’elles ne soient complètement épuisées. Quand la puissance de l’outil utilisé faiblit, l’éteindre et recharger la batterie. Si l’outil continue d’être utilisé jusqu’à épuisement du courant électrique, la batterie risque d’être endommagée et sa durée de vie se raccourcira.
Français 2. Vérifier s’il y a de la poussière. Enlever la poussière avec un chiffon doux ou un chiffon humecté d’eau savonneuse. Ne pas utiliser de décolorant, chlorure, essence ou diluant, car ces produits pourraient endommager le plastique. 3. Liste des pièces de rechange PRECAUTION: Les réparations, modifications et inspections des outils électriques Hitachi doivent être confiées à un service après-vente Hitachi agréé.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de este cargador de baterías, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de un cargador de baterías se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA EL CARGADOR DE BATERÍAS ADVERTENCIA: La utilización inadecuada del cargador de baterías puede resultar en lesiones serias o en la muerte. Para evitar estos riesgos, siga las instrucciones de seguridad ofrecidas a continuación. LEA TODAS LAS INSTRUCCIONES 1. 2. 3. 4. 5. 6. 7. 8. 26 Este manual contiene instrucciones importantes de seguridad para el cargador de baterías modelo UC18YRL y UC18YFL.
Español Tabla 1 CALIBRE (AWG) MÍNIMO RECOMENDADO PARA CABLES PROLONGADORES PARA EL CARGADOR DE BATERÍAS Amperaje nominal de entrada de CA* Igual o superior a pero inferior a 0 2 3 2 3 4 Calibre (AWG) del cable Longitud del cable, Pies (metros) 25 (7,5) 50 (15) 100 (30) 150 (45) 18 18 18 18 18 18 18 16 16 16 14 14 * Si la entrada nominal del cargador de baterías se indica en vatios en vez de amperios, el amperaje nominal correspondiente se determinará dividiendo el vataje por la tensión, por ejemplo
Español 3. 4. NUNCA NUNCA cortocircuite la batería. inserte ningún objeto en las ranuras de ventilación del cargador. Si lo hiciese podría recibir descargas eléctricas o dañar el cargador de baterías. 5. NUNCA cargue en exteriores. Mantenga la batería alejada de la luz solar directa, y utilícela solamente donde haya poca humedad y una buena ventilación. 6. NUNCA cargue cuando la temperatura sea inferior a 32°F (0°C) o superior a 104°F (40°C). 7. NUNCA conecte dos cargadores de baterías juntos. 8.
Español OPERACIÓN Y MANTENIMIENTO NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener este cargador de baterías. NUNCA haga funcionar ni efectúe el mantenimiento del cargador de baterías antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los del propio cargador de baterías.
Español ESPECIFICACIONES Modelo UC18YRL / UC18YFL Fuente de alimentación Monofásica: 120 V CA, 60 Hz de entrada Tiempo de carga Aprox. 20 minutes .......... EB712S, EB7S, EB714S, FEB7S, EB912S, EB9S, EB914S, EB914, FEB9S, EB1212S, EB12S, EB1214S, EB1214L, FEB12S, EB1412S, EB1414S, EB1414, EB1812S, EB1814SL Aprox. 30 minutes .......... EB7B, EB9B, EB12B, EB1220BL, EB14B, EB18B EB1820, EB1820L Aprox. 35 minutes .......... EB924, EB1224, EB1424, EB1824L Aprox. 40 minutes ..........
Español 1. Inserte el enchufe del cargador de baterías en un tomacorriente. Cuando haya insertado el enchufe del cargador de baterías en un tomacorriente, la lámpara piloto parpadeará lentamente en rojo. (A intervalos de 1 segundo) ADVERTENCIA: No utilice el cargador si su cable está dañado. Haga que se lo reparen inmediatamente. 2. Inserte la batería en el cargador de baterías. Inserte la batería en el cargador de baterías como se muestra en la Fig. 2.
Español 䡬 Cuando la batería se haya cargado completamente, la lámpara parpadeará lentamente en rojo. (A intervalos de 1 segundo) (Consulte la Tabla 2.) Tabla 2 Lámpara de indicación del estado de la carga (roja) Indicaciones de la lámpara piloto Se encenderá durante 0,5 segundos. No se encenderá durante 0,5 segundos.
Español 䡬 Tiempo de carga En la Tabla 4 se muestra el tiempo de recarga requerido de acuerdo con el tipo de batería. Tabla 4 Tiempo de recarga (min. aprox.) a 20°C Capacidad de la batería (Ah) Tensión de la batería 7.2V 9.6V 12V 14.4V 18V BATERÍA de Ni-Cd (níquel-cadmio) 1.2–1.4 Ah EB712S EB7S EB714S FEB7S EB912S EB914S EB9S EB914 FEB9S EB12S EB1212S EB1214S EB1214L FEB12S EB1412S EB1414S EB1414 2.0 Ah 2.4 Ah BATERÍA de Ni-MH (níquel-hidruro metálico) BATERÍA de ion de lítio 2.6 Ah 3.0 Ah 3.
Español Forma de hacer que las baterías duren más 䡬 䡬 䢇 䢇 䢇 Recarque las baterías antes de que se hayan agotado completamente. Si siente que la potencia de la herramienta eléctrica se debilita, deje de utilizarla y recargue su batería. Si continuase utilizando la herramienta hasta agotar la capacidad de la batería, ésta podría dañarse y su duración útil podría acortarse. Evite realizar la recarga a altas temperaturas Una batería se calentará inmediatamente después de haberla utilizado.
Español 2. Comprobación del polvo El polvo podrá eliminarse con un paño suave y seco o ligeramente humedecido en agua jabonosa. No utilice lejía, cloro, gasolina, ni diluidor de pintura, porque podrían dañar el plástico. 3. Lista de repuestos PRECAUCIÓN: La reparación, modificación e inspección de las herramientas eléctricas Hitachi deben ser realizadas por un Centro de Servicio Autorizado de Hitachi.
UC18YRL ITEM NO. 36 PART NAME Q'TY 1 HITACHI LABEL 2 PRISM 1 1 3 CASE (A) 1 4 CORD 1 5 FAN 1 6 FUSE (125V, 3.
UC18YFL ITEM NO. PART NAME Q'TY 1 HITACHI LABEL 2 PRISM 1 1 3 CASE (A) 1 4 CORD 1 5 FUSE (125V, 3.
Please contact HITACHI KOKI U.S.A. LTD. at 1-800-59-TOOLS (toll free), or HITACHI AUTHORIZED POWER TOOL SERVICE CENTER recarding COLLECTION. Pour le RAMASSAGE, contacter HITACHI KOKI U.S.A. LTD. au 1-800-59-TOOLS (appel gratuit), ou UN SERVICE APRES-VENTE D’OUTILS ELECTRIQUE AGREE PAR HITACHI. Con respecto a la RECOLECCIÓN de baterías, póngase en contacto con HITACHI KOKI U.S.A. LTD. número 1-800-59-TOOLS (llamada gratis), o con HITACHI AUTORIZED POWER TOOL SERVICE CENTER. Issued by Hitachi Koki Co.