Model Modèle Modelo DH 40MR Rotary Hammer Marteau rotatif Martillo perforador SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool. This manual should be stored in safe place.
English CONTENTS Page Page IMPORTANT SAFETY INFORMATION ................... 3 MEANINGS OF SIGNAL WORDS ........................... 3 ASSEMBLY AND OPERATION .................................. 10 APPLICATIONS ...................................................... 10 PRIOR TO OPERATION .......................................... 10 HOW TO USE ......................................................... 11 USING DRILL CHUCK, CHUCK ADAPTOR ........... 15 HOW TO USE THE CORE BIT ................................
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English (4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. (5) Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. (6) Use safety equipment. Always wear protective glasses. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. 4.
English SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 2. ALWAYS wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. 3. NEVER touch the tool bit with bare hands after operation. 4.
English 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16. NEVER use a tool which is defective or operating abnormally.
English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safey instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
English ASSEMBLY AND OPERATION APPLICATIONS Rotation and hammering function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete Hammering function only 䡬 Crushing concrete, chipping, digging, and squaring (by applying optional accessories) PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. 2. Power switch Ensure that the switch is in the OFF position.
English (1) Clean, then smear the tool shank with the grease provided in the green tube. (2) To attach the tool (SDS max shank), insert it into the hole until it contacts the innermost end of the hole as illustrated in Fig. 2. If you continue to turn the tool with slight pressure, you can feel a spot where there is a hitch. At that spot, pull the grip to the direction of an arrow mark and insert the tool all the way Grip until it hits the innermost end.
English CAUTION: Although this machine is equipped with a safety clutch, if the drill bit becomes bound in concrete or other material, the resultant stoppage of the drill bit could cause the machine body to turn in reaction. Ensure that the main handle and side handle are gripped firmly during operation. 2. How to chisel or crush (Fig. 5) By applying the tool tip to the chiseling or crushing position, operate the rotary hammer by utilizing its empty weight. Forcible pressing or thrusting is unnecessary.
English (1) Switching to “hammering” (a) Push the button, release lock and turn the selector lever counterclockwise. (b) Align ▲ of the selector lever and of the lever holder as illustrated in Fig. 7. (c) Release the button to lock the selector lever. NOTE: Turn the selector lever (do not push the button) to check if it is completely locked and make sure that it does not turn. (2) When fixing working positions of tools such as cold chisel, etc., (a) Push the button, release lock and turn the selector lever.
English 6. Warming up (Fig. 11) The grease lubrication system in this unit may require warming up in cold regions. Position the end of the bit so makes contact with the concrete, turn on the switch and perform the warming up operation. Make sure that a hitting sound is produced and then use the unit. CAUTION: When the warming up operation is performed, hold the side handle and the main body securely with both hands to maintain a secure grip and be careful not to twist your body by the jammed drill bit. 7.
English USING DRILL CHUCK, CHUCK ADAPTOR Note that this machine can be used at “rotation only” if separately sold parts such as drill chuck and chuck adaptor are attached. Use it with the selector lever positioned at “rotation + hammering”. WARNING: During operation, be sure to grip the handle and the side handle firmly to prevent your body from swaying. (1) Switching to “rotation + hammering” For switching to “rotation + hammering”, follow the same procedures mentioned in [3.
English (2) Mount the core bit shank to the Rotary Hammer. (Fig. 16) (3) Insert the center pin into the guide plate until it stops. (4) Engage the guide plate with the core bit, and turn the guide plate to left or right so that it does not fall even if it faces downward. (Fig. 17) Fig. 16 2. How to bore (Fig. 18) (1) Connect the plug to the receptacle. (2) A spring is installed in the center pin. Push it lightly to the wall or the floor straight.
English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the screws Regularly inspect all screws and ensure that they are properly tightened.
English 5. How to replase grease This machine is full air-tight construction to protect against dust and to prevent lubricant leakage. Therefore, the machine can be used without lubrication for long periods. Replace the grease as described below. 䡬 Grease replacement period After purchase, replace grease after every 6 months of usage. Ask for grease replacement at the nearest HITACHI Authorized Service Center. Proceed for replacement of grease.
English 19
English External dia. Overall lenght 13-3/8" (340 mm) 21-1/4" (540 mm) 13-3/8" (340 mm) 21-1/4" (540 mm) 12-5/8" (320 mm) 20-15/32" (520 mm) 12-5/8" (320 mm) 20-15/32" (520 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 5/8" (16 mm) 3/4" (19 mm) 7/8" (22 mm) 1" (25 mm) 1-1/8" (28 mm) 1-1/4" (32 mm) 1-1/2" (38 mm) 1-9/16" (40 mm) Code No.
English 5. Bolt plaching operation with Chemical Anchor (Rotation + Hammering) (Standard socket on the market) (1) Chemical Anchor Adaptor (SDS max shank) Square dimensions of the side of the socket installation Code No. 1/2" (12.7 mm) 313469 3/4" (19.0 mm) 313470 6. Crushing (Hammering) (1) Bull point Overall length Code No. 11" (280 mm) 313471 15-3/4" (400 mm) 313472 7. Groove digging and edging (Hammering) (1) Cold chisel Overall length Code No.
English 10. Surface Roughing (Hammering) (2) Shank (1) Bushing Tool Code No. 313477 Overall length Code No. 8-21/32" (220 mm) 313479 11. Tamping (Hammering) (2) Shank (1) Rammer Code No. 313478 Overall length Code No. 8-21/32" (220 mm) 313479 12. Syringe (for chip removal) Code No. 944575 13. Hammer grease A 1.1 lbs (500 g) (in a can) Code No. 980927 0.15 lbs (70 g) (in a green tube) Code No. 308471 NOTE: Specifications are subject to change without any obligation on the part of the HITACHI.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français (2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties mobiles. Les vêtements larges, les bijoux et les cheveux longs peuvent se prendre dans les parties mobiles. (3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation est sur la position d’arrêt avant de brancher la machine.
Français (2) Lors de la réparation d’un outil, utiliser uniquement des pièces de rechange identiques. Suivre les instructions de la section d’entretien de ce mode d’emploi. L’utilisation de pièces non autorisées ou un non respect des instructions d’entretien peut créer un risque d’électrocution ou de blessures. REGLES DE SECURITE SPECIFIQUES ET SYMBOLES 1.
Français 11. Maintenir toutes les vis, tous les boulons et les couvercles fermement en place. Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier leurs conditions périodiquement. 12. Ne pas utiliser les outils motorisés si le revêtement de plastique ou la poignée est fendu. Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels outils ne doivent pas être utilisés avant d’être réparé. 13.
Français 22. Définitions pour les symboles utilisés sur cet outil V ............ volts Hz .......... hertz A ............ ampères no .......... vitesse sans charge W ........... watt .......... Construction de classe II ---/min ... tours par minute .......... Courant alternatif DOUBLE ISOLATION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus sûr de cet outil motorisé, HITACHI a adopté une conception à double insolation.
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS Fonction de rotation et de percussion 䡬 Perçage de trous d’ancrage 䡬 Perçage de trous dans béton Fonction de percussion uniquement 䡬 Broyage du béton, burinage, creusage et équarrissage (par application des accessoires optionnels) AVANT L’UTILISATION 1. Source d’alimentation S’assurer que la source d’alimentation qui doit être utilisée est conforme à la source d’alimentation requise spécifiée sur la plaque signalétique du produit. 2.
Français (1) Nettoyer, puis graisser la queue de l’outil avec la graisse fournie à cet effet en tube vert. (2) Pour fixer l’outil (tige SDS max), l’insérer dans l’orifice jusqu’à ce qu’il touche l’extrémité intérieure de l’orifice comme indiqué sur la Fig. 2. Si l’on continue à tourner l’outil en exerçant une légère pression, l’on sentira un endroit où il y a un obstacle.
Français PRECAUTION: Bien que cette machine soit équipée d’un cran de sécurité, si la mèche est prise dans le béton ou autre matériel l’arrêt de son fonctionnement pourrait faire tourner le corps de la machine. Tenir fermement la poignée principale et la poignée latérale pendant le fonctionnement. 2. Comment buriner ou broyer (Fig. 5) En appliquant l'outil sur la position de burinage ou de broyage, faire fonctionner le marteau rotatif en utilisant son propre poids.
Français (1) Commutation sur “percussion” (a) Appuyer sur le bouton, libérer le verrou et tourner le levier de sélection dans le sens inverse des aiguilles d’une montre. (b) Aligner ▲ du levier de sélection sur du support de levier comme indiqué sur la Fig 7. (c) Relâcher le bouton pour verrouiller le levier de sélection. Sélecteur Cache inférieur Button REMARQUE: Tourner le sélecteur (ne pas appuyer dessus) pour voir s’il est bien verrouillé à fond et s’assurer qu’il ne tourne pas.
Français 6. Préchauffage (Fig. 11) Le système de graissage de l’outil risque de devoir être préchauffé dans les régions froides. Placer l’extrémité de la mèche de façon qu’elle entre en contact avec le béton, enclencher l’interrupteur et effectuer une opération de préchauffage. Bien s’assurer que l’outil fait entendre un bruit de heurt, puis utiliser l’outil.
Français (1) Commutation sur “rotation + percussion” Pour commuter sur “rotation + percussion”, procéder comme indiqué au point [3. Perçage en “rotation + percussion”]. (2) Fixation du raccord de mandrin sur le mandrin Mandrin Tige SDS max porte-foret (Fig. 14) porteAttache Raccord de (a) Fixer le raccord de mandrin sur le mandrin foret coulissante mandrin porte-foret. (b) La tige SDS max du raccord de mandrin est Fig. 14 l’équivalent du foret de perçage.
Français (4) Engager la plaque de guidage dans la couronne et tourner la plaque de guidage à gauche ou à droite de manière à ce qu’elle à ce qu’elle ne puisse pas tomber, même si elle orientée vers le bas. (Fig. 17) Goujon central Couronne Bout de couronne 2. Perçage (Fig. 18) (1) Brancher la perceuse. (2) Un ressort est placé dans le goujon central. Appuyer légèrement l’outil contre le mur ou le plancher tout droit. Toute la surface de la couronne doit être en contact avec le mur ou le plancher.
Français ENTRETIEN ET INSPECTION AVERTISSEMENT: S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspectio. 1. Contrôle du foret de perçage Etant donné que l’utilisation d’une mèche usée entraînera un mauvais fonctionnement du moteur et une diminution de l’efficacité, remplacez la mèche usée par une neuve ou aiguisez-la immédiatement et dès que vous notez une certaine usure. 2.
Français 䡬 Remplacement du balais en carbone Desserrer la vis de fixation et enlever le couvercle de la queue. Enlever la chapeau de balai et la balai en carbone. Après avoir remplacé le balai en carbone, serrer fermement le chapeau du balai et installer le couvercle avec deux vis de fixation. 5. Comment remplacer la graisse Cette machine est de contruction entièrement hermétique pour la protéger contre la poussière et pour éviter les fuites de lubrifiant.
Français 39
Français Diamètre extérieur Longueur totale 13-3/8" (340 mm) 21-1/4" (540 mm) 13-3/8" (340 mm) 21-1/4" (540 mm) 12-5/8" (320 mm) 20-15/32" (520 mm) 12-5/8" (320 mm) 20-15/32" (520 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 14-9/16" (370 mm) 22-7/16" (570 mm) 5/8" (16 mm) 3/4" (19 mm) 7/8" (22 mm) 1" (25 mm) 1-1/8" (28 mm) 1-1/4" (32 mm) 1-1/2" (38 mm) 1-9/16" (40 mm) No.
Français 5. Mise en place du boulon pour d’ancre chimique (Rotation + Percussion) (Support standard disponible dans le commerce) (1) Raccord d’ancre chimique (Tige SDS max) Dimensions du carré du côté de l’installation du support No. de code 1/2" (12,7 mm) 313469 3/4" (19,0 mm) 313470 6. Broyage (Percussion) (1) Point de broyage Longueur totale No. de code 11" (280 mm) 313471 15-3/4" (400 mm) 313472 7.
Français 10. Dégrossissage (Percussion) (2) Queue (1) Boucharde No. de code 313477 Longueur totale No. de code 8-21/32" (220 mm) 313479 11. Bourrage (Percussion) (2) Queue (1) Bourroir No. de code 313478 Longueur totale No. de code 8-21/32" (220 mm) 313479 12. Seringue (pour enlever déchets) No. de code 944575 13. Graisse A pour marteau 1,1 lbs (500 g) (en boîte) No. de code 980927 0,15 lbs (70 g) (en tube vert) No.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES. 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español (2) Vístase adecuadamente. No utilice ropa floja ni joyas. Si tiene pelo largo, recójaselo. Mantenga su pelo, ropa, y guantes alejados de las partes móviles. La ropa floja, las joyas, o el pelo largo pueden engancharse en las partes móviles. (3) Evite la puesta en marcha accidental. Cerciórese de que la alimentación de la herramienta eléctrica esté desconectada antes de enchufarla en una toma de la red.
Español (2) Para el servicio de mantenimiento o reparación de una herramienta, utilice solamente piezas de repuesto idénticas. Siga las instrucciones de la sección de mantenimiento de este manual. La utilización de piezas no autorizadas, o el no seguir las indicaciones del Manual de instrucciones puede crear el riesgo de descargas eléctricas u otras lesiones. NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD 1.
Español 11. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 12. No utilice herramientas eléctricas si la carcasa o la empuñadura de plástico está rajada. Las rajas en la carcasa o en la empuñadura de plástico pueden conducir a descargas eléctricas. Tales herramientas no deberán utilizarse mientras no se hayan reparado. 13.
Español 22. Definiciones para los símbolos utilizados en esta herramienta V ............ voltios Hz .......... hertzios A ............ amperios no .......... velocidad sin carga W ........... vatios .......... Construcción de clase II ---/min ... revoluciones por minuto .......... Corriente alterna AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIÓN MÁS SEGURA Para garantizar una operación más segura de esta herramienta eléctrica, HITACHI ha adoptado un diseño de aislamiento doble.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español MONTAJE Y OPERACIÓN APLICACIONES Función de rotación y golpeteo 䡬 Perforación de orificios de anclaje 䡬 Perforación de orificios en hormigón Función de martilleo solamente 䡬 Trituración de hormigón, cincelado, excavación y escuadreo (utilizando accesorios opcionales) ANTES DE LA OPERACIÓN 1. Fuente de alimentación Cerciórese de que la fuente de alimentación que vaya a utilizar cumpla los requisitos indicados en la placa de características del producto. 2.
Español 6. Montaje de la herramienta PRECAUCIÓN: Para usar herramientas tales como el puntero y, usar siempre piezas genuinas Hitachi. (1) Limpiar y engrasar la espiga con la grasa provista. (2) Para fijar la herramienta (espiga SDS max), insértela en el orificio hasta que entre en contacto con el extremo interior del mismo, como se muestra en la Fig. 2. Si continúa girando la herramienta con una ligera presión, podrá sentir un punto en el que note un obstáculo.
Español (2) No es necesario presionar el cuerpo principal del martillo perforador. Es suficiente con empujar ligeramente el martillo perforador teniendo en cuenta que los materiales saltan libremente, al taladrar. PRECAUCIÓN: Aunque este aparato se equipa con un embrague de seguridad, si se atasca la barrena de taladrar en el hormigón u otro material semejante, puede pasar que, al atascarse la barrena, el cuerpo del martillo gire en dirección opuesta.
Español Palanaca selectora Cubierta inferior (1) Cambio a “martilleo” (a) Apriete el botón, desbloquee la palanca selectora y gírela en el sentido contrario a las agujas del reloj. (b) Alinee la marca ▲ de la palanca selectora y del sujetador de palanca, tal como se muestra en la Fig. 7. (c) Suelte el botón para bloquear la palanca selectora. Botón NOTA: Fig.
Español 6. Calentamiento (Fig. 11) El sistema de lubricación de esta unidad puede requerir calentamiento en ciertas regiones. Coloque el extremo de la broca de forma que entre en contacto con el hormigón, ponga en ON el interruptor de alimentación principal de la unidad, y realice la operación de calentamiento. Cerciórese de que se produzca un sonido de martilleo, y después utilice la unidad.
Español (1) Cambio a “rotación + martilleo” Para cambiar a “rotación + martilleo”, realice los mismos procedimientos que los mencionados en [3. Cuando taladre con “rotación + martilleo”]. (2) Fijación del adaptador para portabarrenas al portabarrenas (Fig. 14) (a) Fije el adaptador para portabarrenas al portabarrenas. (b) La espiga SDS max del adaptador para Portabrocas Espiga portabarrenas es equivalente a la barrena.
Español (4) Unir la placa guía con la barrena tubular y girar la placa guía hacia la izquierda o hacia la derecha de forma que no se caiga a pesar de estar indicando hacia abajo. (Fig. 17) 2. Modo de taladrar (Fig. 18) (1) Conectar el enchufe a la toma de alimentación. (2) El pasador central se ha instalado un resorte. Presionar ligeramente y sin torcerse hacia la pared o hacia el pared o hacia el suelo.
Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspeccionar la broca de taladro Debido a que el uso de brocs desafiladas pueden causar mal funcionamiento del motor y desmejorar la eficacia del taladro, hay que reemplazar las brocas en malas condiciones por nuevas o afilarlas de inmediato al advertir abrasión. 2.
Español 䡬 Cambio de escobillas de carbón Quitar la cubierta de cola y luego aflojar el tornillo de fijación. Aflojando la tapa de escobilla, pueden quitarse las escobillas de carbón, al colocar las escobillas, apretar firmemente la tapa de escobillas y recolocar la cubierta de con dos tornillos. 5. Cambio de grasa Esta máquina es de construcción completamente cerrada, para evitar que entre polvo y haya fugas de lubricante. Por ello, la herramienta puede usarse sin lubricarse por largos periodos.
Español 59
Español 60
Español 61
Español 62
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.