CCD camera KP-FD140F KP-FD32F KP-F140F KP-F32F KP-F83F Operation Manual Thank you for producing this fine Hitachi Kokusai Electric CCD camera. Before using the camera, please read this operation manual carefully and keep this manual on file for ready reference in the future. Hitachi Kokusai Electric RoHS Compliant These products compile with the requirement of he RoHS (Restriction of the use of Certain Hazardous Substances in Electrical and electronic Equipment) Directive 2002/95/EC.
IMPORTANT SAFETY INSTRUCTIONS 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety and operating instructions should be retained for future reference. 3. Heed Warnings All warnings on the product and the operating instructions should be adhered to. 4. Follow Instructions All operating and use instructions should be followed. 5. Cleaning Unplug this product from the wall outlet before cleaning.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power-supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the operating instructions.
Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben werden. Wenn Sie nicht sicher sind, was für eine Stromversorgung Sie haben, so wenden Sie sich bitte an Ihren Erzeugnishändler oder an das lokale Elektrizitätswerk. Beziehen Sie sich für Batteriebetrieb oder andere Stromquellen vorgesehene Erzeugnisse bitte auf die Bedienungsanleitungen. 12.
2. Conserver ces instructions Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure. 3. Tenir compte des avertissements Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés. 4. Observer les instructions Observer toutes les instructions de fonctionnement et d’utilisation. 5. Nettoyage Avant de procéder au nettoyage, débrancher l’appareil de la prise secteur. Ne pas utiliser de produits de nettoyage liquides ou en aérosol.
20. Dommages nécessitant réparations Débrancher l’appareil de la source d’alimentation et confier les réparations á un personnel qualifié dans les cas suivants: a. Lorsque le cordon d’alimentation ou sa fiche sont endommagés b. Si du liquide s’est renversé sur l’appareil ou que des objets sont tombés dedans c. Si l’appareil a été exposé á la pluie ou á l’eau. d. Si l’appareil ne fonctionne pas normalement lorsqu’on observe les instructions d’utilisation.
Phenomena inherent to CCD imaging device The following phenomena are inherent to a charge coupled device imaging element and do not indicate malfunction. 1) Smear and blooming Vertical bands are visible when a strong light enters the scene. to avoid strong direct or reflected light. Adjust the camera aiming direction carefully 2) Fixed pattern noise High ambient temperature can cause fixed pattern noise to appear throughout the scene.
6. Cleaning ・ Use a blower or a lens brush to remove dusts on the lens or the optical filter. ・ Wipe dirts on the case off with dry soft cloth. If dirks are hardened, wipe them off with cloth moistened with neutral detergent liquid; wipe the cover with dry cloth. ・ Do not use benzene, thinner, alcohol, liquid cleaner or spray-type cleaner. ・ In event dust or other debris is lodged between the CCD and optical filter, consult dealer for cleaning by an optical technician.
Table of Contents 1. Overview ······································································································································································································ 1 2. Standard Composition ··········································································································································································· 1 3.
Overview The KP-FD140F/FD32F are single CCD type RGB color camera which utilized the progressive scan CCD image sensor with square pixel for SXGA/VGA format of 1/2-inch which adopted the RGB primary color mosaic filter. The KP-F140F/F32F are a monochrome CCD camera which utilized the progressive scan CCD image sensor with square pixel for SXGA/VGA format of 1/2-inch. The KP-F83F is a monochrome CCD camera which utilized the progressive scan CCD image sensor with square pixel for XGA format of 1/3-inch.
Section name and functions Camera / Tripod adaptor mounting screw holes PLATE,RATED POWER/STATUS LED LED Green Power ON Light Off Transmission Blink Off Transmission pause Blink On Lens mount (C mount) Yellow Light off Blink On Blink Off P OWE R/ST A T US P ORT 1 P ORT 2 IEEE1394 connectors *1 Connect to IEEE1394 connector of PC using IEEE1394 cable. *1 When power is supplied from IEEE1394, check for proper current and voltage.
Camera mounting Attached optional accessory the tripod adaptor "TA-FD140", mount the camera to a tripod or mounting bracket. L Screw type: U1/4-20 Length L = 4 to 5.5mm Screws longer than 5.5 mm can cause internal damage, while less than 4 mm prevents secure fastening and risks dropping to cause damage and injury. Lens CAUTION Observe the dimensions of the lens mounting selection as illustrated at the right.
Control and States Register KP-FD140F/F140F/FD32F/F32F/F83F can be set by entering predetermined setting commands in the Control and Status register (CSR) of the 1394-based Digital Camera Specification Ver. 1.31. Common and camera-specific CSR register setting operations are described below. Indication example: Function name (CSR: xxxx xxxx h) Function description Lower 32 bits of 64 bit CSR address are displayed. ex: F0F0 0800 h means BUS_ID, NODE_ID, FFFF F0F0 0800 h. 1.
-AUTOSetting value 83000000 h Gain is automatically adjusted in the range of 0 to 18 dB in response to light source brightness. (5) SHUTTER (CSR: F0F0 081C h) Sets electronic shutter speed. -OFFSetting value 80000000 h Switches off shutter operation. *The shutter speed (at OFF) is as follows.
(CSR: F0F0-0818 h) Gamma correction is adjusted. -OFFSetting value 80000000h Gamma correction is set to OFF. -Manual adjustmentSetting value 820000xx h xx: 00h to FFh (Standard 00h) Adjust the detail gamma. ON Output (7) GAMMA OFF (8) TRIGGER Sets external trigger operating mode. -OFFSetting value 80000000h Trigger function set to OFF.
(14) CURRENT MEMORY (CSR: F0F0 0624 h) Loading memory channel designating data -LOADBACK UP executeSetting value x0000000 h x: 0- FACTORY SETUP, 1- ch1, 2- ch2, 3- ch3, 4- ch4 2. Advance CSR 2-1. Image color reproduction and color balance related CSR (1) MASKING (CSR: F200-0020 h) RGB and Ye Cy Mg color saturation and hue can be separately varied (6 vector independent masking). Color reproduction detail and fidelity are effectively enhanced.
i) (MASKING) G HUE -Manual adjustmentSetting value 820000xx h j) (MASKING) C HUE -Manual adjustmentSetting value 820000xx h k) (MASKING) B HUE -Manual adjustmentSetting value 820000xx h l) (MASKING) M HUE -Manual adjustmentSetting value 820000xx h (CSR: F200 0044 h) xx: 00h to FFh (standard 80h) (CSR: F200 0048 h) xx: 00h to FFh (standard 80h) (CSR: F200 004C h) xx: 00h to FFh (standard 80h) (CSR: F200 0050 h) xx: 00h to FFh (standard 80h) (2) PAINT BLACK Color level of R,G, and B can be separately varied
-OFFSetting value 80000000 h -ONSetting value 8xy0000z h x: 2- LOW ACTIVE, 3- HIGH ACTIVE y: 0- SourceID0(PORT1), 2- SourceID1(PORT2), E- SourceID7(Software) z: 1- SET Readout signal polarity is switched at value of x. Readout signal source is switched at value of y. When set SourceID7, if z is set to 1, a picture is outputted (and z becomes 0 automatically). (3) TIME STAMP (CSR: F200 000C h) The cycle timer value of 1394 buses can be added to image data as the time stamp.
Video format 1. KP-FD140F/F140F A. Fixed format Frame Rate Format Mode Image Size Color Coding 30 15 7.5 3.75 1.
3. KP-FD32F/F32F A. Fixed format Frame Rate Format Mode Image Size Color Coding 60 30 15 7.5 3.75 1.875 0 3 640 x 480 4 640 x 480 YUV(4:2:2) ○(*) ○ ○ ○ ○ ○ RGB ○(*) ○ ○ ○ ○ ○ 5 640 x 480 YMONO8 ○ ○ ○ ○ ○ ○ 6 640 x 480 YMONO16 ○(*) ○ ○ ○ ○ ○ B.
Trigger operation and timing chart 1. Normal mode Shutter time (Camera setting value) Shutter time (Camera setting value) Shutter time Strobe delay Strobe output (High output) Data output (*1) Strobe duration1 Strobe duration2 (*2) (*3) VD output (Low active) (*1) 0.27~3930.51μs 0.96μs/step (*2) 0.96~3931.2μs 0.96μs/step (*3) Shutter Time – Strobe delay (when duration time is set to 000h) DATA 3.2 0.9 3.2 0.9 0.
2. Fixed shutter mode (External trigger operating mode: Mode 0) When external trigger signal is high active, after the trigger signal rise edge, the strobe signal start/end can be set to determine the strobe time. At the strobe signal falling edge, the internal VD signal is reset and the video data are transmitted.
4. Reset control (External trigger operating mode: Mode 14) When the external trigger signal is HIGH ACTIVE, exposure begins at the rising edge of the trigger signal and ends at the falling edge. At the Readout pulse falling edge, the internal VD signal is reset and the video data are transmitted.
5. VD synchronization (External trigger operating mode: Mode 15) Please input the sync pulse of following specification, in the case that camera synchronization locks the external synchronization. more than 1/self frame rate [sec] VD input (Low active) more than 10μs DATA 3.2 0.9 3.2 0.9 0.
Specifications Specifications of KP-FD140F/F140F/FD32F/F32F/F83F are showing. KP-FD140F/F140F KP-FD32F/F32F KP-F83F 1) Imaging device 1/2-inch interline CCD 1/3-inch interline CCD Total pixels 1434 (H) x 1050 (V) 692(H) x 504(V) 1079(H) x 789(V) Effective pixels 1392 (H) x 1024 (V) 656(H) x 492(V) 1034(H) x 779(V) Pixel size 4.65μm (H) x 4.65μm (V) 9.9μm (H) x 9.9μm (V) 4.65μm (H) x 4.
Dimensions ・UNIT : mm ・MASS : APPROX 130 g PORT 1 25 ±1 SEE MANUAL APERCEVOIR MANUEL POWER/STATUS PORT 2 2-M3(DEPTH:3) COLOR:BLACK VIEW “A” ±1 ±1 11.5 34 (5.7) 2-M2(DEPTH:3) ±1.5 ±1.5 44 54 ±1 (6) A 22 ±1 44 B U1 ±1.5 22 COLOR:BLACK VIEW “B” (5.7)11.
About CD-ROM Attached CD-ROM has the following composition. * means folder. Reame.txt *HitachiKokusai *Documents *Viewersoftware *Technoscope *Documents *Driver *ZCL-1 *Japanese CameraOperationManual(J).pdf, VieweManual(J).pdf *English CameraOperationManual(E).pdf, ViewerManual(E).pdf HiKE1394CamView.exe ZCLAPI.pdf, ZCLDrvInstall.pdf COM.dll, ZCL.dll, ZCLDrv.dll, ZCLDrv.inf, ZCLDRV.sys *COMMON ZCL.lib, ZCLAPI.h *Sample1: (Source cord of sample program 1) *SampleEXE Sample1.exe, test.exe (1) Readme.
Hitachi Kokusai Electric Inc. UDX Akihabara Bldg. 14-1 Kanda 4-choume, Chiyoda-ku, Tokyo 101-8980, Japan Phone: (03) 5209-5931, Fax: (03) 5209-6119 URL: http://www.h-kokusai.com Beijing Office Beijing Fortune Building 5, Dong San Huan Bei-lu, Chao Yang District, Beijing, 100029 Chaina Phone: +86(0) 10-6590-8755/8756, Fax: +86(0) 10-6590-8757 HITACHI KOKUSAI Electric AMERICA, LTD. Headquarters and : 150 Crossways Park Drive, Woodbury, New York 11797, U.S.A.