FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules.
READ THIS FIRST Trademark Information Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation. Pentium® is a registered trademark of Intel Corporation. Macintosh is a trademark of Apple Inc. SD™ is a trademark. SDHC™ is a trademark. Other names and products may be trademarks or registered trademarks of their respective owners. Product Information Product design and specifications are subject to change without notice.
SAFETY INSTRUCTIONS Read and understand all Warnings and Cautions before using this product. Warnings If foreign objects or water have entered the camera, turn the power off and remove the battery. Continued use might cause fire or electric shock. Consult the store of purchase. If the camera has fallen or its case has been damaged, turn the power off and remove the battery. Continued use might cause fire or electric shock. Consult the store of purchase. Do not disassemble, change or repair the camera.
Cautions Insert the battery paying careful attention to the polarity (+ or –) of the terminals. Inserting the battery with its polarities inverted might cause fire and injury, or damage to the surrounding areas due to the battery rupturing or leaking. Do not fire the flash close to anyone’s eyes. This might cause damage to the person’s eyesight. Do not subject the LCD monitor to impact. This might damage the glass on the screen or cause the internal fluid to leak.
Notes on Battery Usage When you use the battery, carefully read and strictly observe the Safety Instructions and the notes described below: Use only the specified battery (3.7V). Avoid extremely cold environments as low temperatures can shorten the battery life and reduce camera performance.
CONTENTS 7 INTRODUCTION 20 PLAYBACK MODE 7 7 Overview Package Contents 8 GETTING TO KNOW YOUR CAMERA 8 8 9 Front View Rear View LCD Monitor Display 20 20 21 21 22 23 24 11 GETTING STARTED 11 Preparation 11 Charging the Battery 12 Initial Settings 14 CAPTURE MODE Playing Back Still Images Playback Display Removing Red-eye Dynamic Lighting Feature Protecting Images DPOF Settings Erasing Images 25 MENU OPTIONS 25 27 28 30 Capture Menu Video Menu Playback Menu Setup Menu 14 Capturing Images 15 Se
INTRODUCTION Overview Congratulations on your purchase of the new digital camera. Capturing high-quality digital images is fast and easy with this state-of-the-art smart camera. Equipped with a 12.0-megapixel CCD, this camera is capable of capturing images with a resolution of up to 3968 x 2976 pixels.
GETTING TO KNOW YOUR CAMERA Front View 1 2 3 4 1. Shutter button 2. Self-timer LED 3. ON/OFF Power button 4. Flash 5. Microphone 6. Lens 5 6 Rear View 1 A A. LCD monitor B 2 B. Status LED 3 C. Strap holder 4 5 6 7 8 9 C E. Tripod socket 10 Item 1. 2. D. Battery / Memory card cover E F F.
LCD Monitor Display 1 2 3 4 Capture mode 19 1. Zoom status 2. Available number of shots 3. Storage media [r] Internal memory (no card) [ ] SD/SDHC memory card 4. Battery condition [l] Full battery power [o] Medium battery power [n] Low battery power [m] No battery power 5. Focus setting [K] Auto [ ] AF Tracking [ ] Face Detect [O] Macro [Q] Infinity 6. Flash mode [b] Auto [a] Flash On [d] Flash Off [c] Red-eye [`] Slow Sync [_] Pre-flash 7.
Video mode 1. Zoom status 2. Storage media 3. Battery condition 4. Focus setting 5. Flash off 6. Self-timer icon 7. Video resolution 8. Available recording time/Elapsed time 9. Date and time 10. Video quality 11. Audio off 12. Mode icon 13. Main focus area Playback mode!-!Still image playback 1. DPOF icon 2. Protect icon 3. Folder / File number 4. Storage media 5. Battery condition 6. Image size resolution 7. Date and time 8. Histogram 9. Shutter speed/Aperture value 10. Exposure value 11. Image quality 12.
GETTING STARTED Preparation 1. 2. 3. 4. Attach the camera strap. Open the battery/memory card cover. Insert the supplied battery with correct orientation as shown. (label side back) Insert an SD/SDHC memory card (Optional). The camera has 32MB internal memory(10MB available for image storage), but you can load an SD/SDHC memory card to expand the camera’s memory capacity. Be sure to format the memory card with this camera before its initial usage. 5.
Initial Settings Setting the Date and Time The date/time needs to be set if and when: The camera is turned on for the first time. The camera is turned on after leaving the camera without the battery for an extended period of time. When the date and time information is not displayed on the LCD monitor, follow these steps to set the correct date and time. 1. Press the MODE button, and set the camera mode to [ ] or [ ]; or press the 7 button. 2. Press the MENU button. 3.
Choosing the Language Specify in which language menus and messages are to be displayed on the LCD monitor. 1. Press the MODE button, and set the camera mode to [ ] or [ ]; or press the 7 button. 2. Press the MENU button. 3. Select the [Setup] at the end of the Menu with the c / d buttons, and press the SET button. 4. Select [Language] with the c / d buttons and press the SET button. 5. Select the displayed language with the e / f / c / d buttons and press the SET button. The setting will be stored. 6.
CAPTURE MODE Capturing Images Your camera is equipped with a 2.36” full colour TFT LCD monitor to help you compose images, playback recorded images/video clips or adjust menu settings. 1. Press the ON/OFF button to turn the power on. ]. 2. Press the MODE button, and set the camera mode to [ 3. Compose your image in the LCD monitor. Turn the zoom lever to side to zoom in on the subject, and enlarges the subject on the LCD monitor.
Setting the Scene Mode By simply selecting one of the available scene modes, you can capture the image with the most appropriate settings. 1. Press the MODE button, and set the camera mode to [ 2. Select the desired scene mode with the e / f / c / d buttons, and press the SET button. 3. Compose the image and press the shutter button. ], and press the SET button.
Scene mode Description Fireworks Select this mode when you want to capture fireworks clearly with optimal exposure. The shutter speed becomes slower, so using a tripod is recommended. Text Select this mode when you want to capture an image that contains black and white subjects like printed documents. Sunset Select this mode when you want to capture a sunset. This mode helps keep the deep hues in the scene. Sunrise Select this mode when you want to capture a sunrise.
Setting the Panorama Mode This mode is designed to make it easier to take a series of shots then stitch them together with software to make a single image. You can capture a photographic subject that won’t fit into a single frame, such as a landscape, and stitch it together later with a program such as Arcsoft Panorama Maker® 4.0 application. 1. Press the MODE button, and set the camera mode to [ ], and press the SET button. 2. Select [Panorama] with the e / f / c / d buttons, and press the SET button. 3.
Recording Shots using Face Detection Technology Face Detection Technology can identify and focus on the human faces in the image. ]. 1. Press the MODE button, and set the camera mode to [ 2. Press the button, and select [ ] icon with the e / f buttons. Press the SET button. With Face Detection turned on, the camera identifies main face (white frame) and subsidiary faces (gray frames). If the camera cannot detect and track any faces, there will be no frame shown on the screen. 3.
VIDEO MODE Recording Video Clips This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 / 720p pixels. 1. Press the MODE button, and set the camera mode to [ ]. 2. Compose the image. 3. Press the shutter button. The recording of the video clip will start. Pressing the shutter button one more time will end the recording of the video clip. The recording time depends on the storage size and the subject of the image to be recorded.
PLAYBACK MODE Playing Back Still Images You can play back the still images on the LCD monitor. 1. Press the 7 button. The last image appears on the screen. 2. The images can be displayed in forward or reverse sequence with the e / f buttons. To view the previous image, press the e button. To view the next image, press the f button. Turn the zoom lever to side enlarges the image. To return to normal magnification, turn the zoom lever to side. An [ ] icon is displayed with the video data.
Removing Red-eye You can use this function to remove the red-eye effect after an image is taken. 1. Press the 7 button. The last image appears on the screen. 2. Select the image that you want to edit with the e / f buttons. 3. Press the MENU button. 4. Select [Fix Red Eyes] with the c / d buttons, and press the SET button. 5. Select [Execute] with the e / f buttons, and press the SET button. 6. View the changes on the corrected image. 7.
Protecting Images Set the data to read-only to prevent images from being erased by mistake. 1. Press the 7 button. Setup The last image appears on the screen. 2. Select the image that you want to protect with the e / Date/Time 2010.01.01 f buttons. Language 3. Press the MENU button. English 4. Select [Protect] with the c / d buttons, and press the Auto Off SET button. ; Off 5. Select [Single] or [All] with the e / f buttons, and press SET button. 6.
DPOF Settings DPOF is the abbreviation for Digital Print Order Format, which allows you to embed printing information on your memory card. You can select the images to be printed and how many prints to make with the DPOF menu in the camera and insert the memory card to the card compatible printer. When the printer starts printing, it will read the embedded information on the memory card and print the specified images. 1. Press the 7 button. The last image appears on the screen. 2.
Erasing Images Erasing a single image / Erasing all images 1. Press the 7 button. The last image appears on the screen. 2. Select the image you want to erase with the e / f buttons. 3. Press the MENU button. 4. Select [Delete] with the c / d buttons, and press the SET button. 5. Select [Single] or [All] with the e / f buttons, and press the SET button. [Single]: Erases the selected image or the last image. [All]: Erases all of the images except for the protected images. 6.
MENU OPTIONS Capture Menu This menu is for the basic settings to be used when capturing still images. 4 MP AUTO MENU ; SET ; MENU ; SET ; Press the ON/OFF button to turn the power on. Press the MODE button, and set the camera mode to any scene mode. Press the MENU button to enter the [Capture] menu. Select the desired option item with the c / d buttons, and press the SET button to enter its respective menu. The selectable items may vary in different capture modes. 5.
Metering This sets the metering method for calculating the exposure. * Center: * Spot: * Average: Averages the light metered from the entire frame, but gives greater weight to the subject matter at the center. A very small portion of the center of the screen is measured to calculate the correct exposure. The exposure is measured all of the image area. Capture Md. This sets the recording method at the time of capturing images . * Single: * Continuous: * AEB: * Album Shot: * Burst: * Cont.
Video Menu This menu is for the basic settings to be used when recording video clips. MENU ; SET ; MENU ; SET ; 1. Press the MODE button, and set the camera mode to [ ]. 2. Press the MENU button to enter the [Video] menu. 3. Select the desired option item with the c / d buttons, and press the SET button to enter its respective menu. 4. Select the desired setting with the e / f buttons, and press the SET button. 5. To exit from the menu, press the MENU button.
Playback Menu In the [7] mode, choose which settings are to be used for playback. ; ; MENU ; SET ; 1. Press the 7 button. 2. Press the MENU button. 3. Select the desired option item with the c / d buttons, and press the SET button to enter its respective menu. 4. Select the desired setting with the e / f buttons, and press the SET button. 5. To exit from the menu, press the MENU button. Delete Refer to the section in this manual titled “Erasing Images” for further details.
Qual. Change Changes the quality (compression) of a recorded image. Compress images down to half of their size or less, overwrite old size images with newly compressed images. It is only possible to reduce the image quality/size, never to increase it. Copy to Card Allows you to copy your files from the camera’s internal memory to an SD/SDHC memory card. Of course, you can only do this if you have a memory card installed and some files in internal memory.
Setup Menu Set your camera’s operating environment. Off ; ; MENU ; SET ; ] or [ ]; or press the 7 1. Press the MODE button, and set the camera mode to [ button. 2. Press the MENU button. 3. Select the [Setup] at the end of the Menu with the c / d buttons, and press the SET button. 4. Select the desired option item with the c / d buttons, and press the SET button to enter its respective menu. 5. Select the desired setting with the e / f buttons, and press the SET button. 6.
Fr. No. Reset This creates a new folder. The captured images are recorded to the newly created folder from number 0001. * Cancel / Execute LCD Bright. Select a brightness level for the LCD monitor. * Standard / Bright Format Refer to section in this manual titled “Formatting the Memory Card or Internal Memory” for further details. Media Info. This displays the free capacity of the internal memory or the memory card. Sys. Info. This displays the firmware version of the camera. Sys.
TRANSFERRING FILES TO YOUR COMPUTER System Requirement Windows Macintosh Pentium III 1GHz or equivalent Windows 7/XP/Vista 512MB RAM 150MB available hard disk space CD-ROM drive Available USB port PowerPC G3/G4/G5 OS 10.3.9 or later 256MB RAM (512 MB recommended) 128MB available hard disk space CD-ROM drive Available USB port Downloading Your Files 1. 2. 3. 4. 5. 6. Turn on your camera. Connect the camera to your computer with the USB cable.
EDITING SOFTWARE INSTALLATION There are 3 types of software that are included on the CD-ROM: ArcSoft MediaImpression™ - manages your media for you, and gives you tons of fun and exciting ways to create and share projects featuring your photo, video, and music files. Create your own movies or photo slide shows, complete with soundtrack; edit, enhance, and add fun creative effects to your photos; and share your files easily through simple email attachments or popular photo printing and video sharing websites.
SPECIFICATIONS Item Description Image sensor 1/2.33” CCD sensor (12.0 megapixels) Image resolution Still image 12M (3968X2976), 8M(3264 x 2448) ,4M (2304x1728), 2M(1600 x 1200) ,VGA(640 x 480) Video clip VGA(640x480)/30fps, QVGA(320x240)/30fps, HD(720p)/30fps LCD monitor 2.36” full colour TFT LCD (112K pixels) Recording media 32MB internal memory (10MB available for image storage) Supports SD/SDHC memory card (up to 16GB) (optional) File format DCF, JPEG (EXIF 2.
APPENDIX Possible Number of Shots Possible number of shots (still image) The table shows the approximate shots that you can capture at each setting based on the capacity of the internal memory and the SD/SDHC memory card.
Troubleshooting Refer to the symptoms and solutions listed below before sending the camera for repairs. If the problem persists, contact your local reseller or service center. Symptom Cause Solutions / Corrective Actions The power does not come on. The battery is not inserted. Insert the battery correctly. The battery is exhausted. Recharge the battery. The battery runs out quickly. The battery is not fully charged. The battery is not used for an extended period of time after being charged.
Language WEEE explanation English The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries as unsorted municipal waste, but use the return and collection systems available. If the batteries or accumulators included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.
Language Norwegian WEEE explanation Symbolet er i samsvar med Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). Symbolet angir kravet på å anvende tilgjengelige retur og gjenvinningssystem, og ikke benytte vanlige usorterte kommunale avfallsordninger, dette gjelder òg batterier og akkumulatorer.
Helpline Number: 08704460806 GETTING TO KNOW YOUR CAMERA Front View 1 2 3 4 1. Shutter button 2. Self-timer LED 3. ON/OFF Power button 4. Flash 5. Microphone 6. Lens 5 6 Rear View 1 A A. LCD monitor B 2 B. Status LED 3 C. Strap holder 4 5 6 7 8 9 C E. Tripod socket 10 Item 1. 2. D. Battery / Memory card cover E F F.
GETTING STARTED Preparation 1. 2. 3. 4. Attach the camera strap. Open the battery/memory card cover. Insert the supplied battery with correct orientation as shown. (label side back) Insert an SD/SDHC memory card (Optional). The camera has 32MB internal memory(10MB available for image storage), but you can load an SD/SDHC memory card to expand the camera’s memory capacity. Be sure to format the memory card with this camera before its initial usage. 5.
CAPTURE MODE Capturing Images Your camera is equipped with a 2.36” full colour TFT LCD monitor to help you compose images, playback recorded images/video clips or adjust menu settings. 1. Press the ON/OFF button to turn the power on. 2. Press the MODE button, and set the camera mode to [ ]. 3. Compose your image in the LCD monitor. Turn the zoom lever to side to zoom in on the subject, and enlarges the subject on the LCD monitor.
VIDEO MODE Recording Video Clips This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 / 720p pixels. 1. Press the MODE button, and set the camera mode to [ ]. 2. Compose the image. 3. Press the shutter button. The recording of the video clip will start. Pressing the shutter button one more time will end the recording of the video clip. The recording time depends on the storage size and the subject of the image to be recorded.
PLAYBACK MODE Playing Back Still Images You can play back the still images on the LCD monitor. 1. Press the 7 button. The last image appears on the screen. 2. The images can be displayed in forward or reverse sequence with the e / f buttons. To view the previous image, press the e button. To view the next image, press the f button. Turn the zoom lever to side enlarges the image. To return to normal magnification, turn the zoom lever to side.
Erasing Images Erasing a single image / Erasing all images 1. Press the 7 button. The last image appears on the screen. 2. Select the image you want to erase with the e / f buttons. 3. Press the MENU button. 4. Select [Delete] with the c / d buttons, and press the SET button. 5. Select [Single] or [All] with the e / f buttons, and press the SET button. [Single]: Erases the selected image or the last image. [All]: Erases all of the images except for the protected images. 6.
TRANSFERRING FILES TO YOUR COMPUTER System Requirement Windows Macintosh Pentium III 1GHz or equivalent Windows 7/XP/Vista 512MB RAM 150MB available hard disk space CD-ROM drive Available USB port PowerPC G3/G4/G5 OS 10.3.9 or later 256MB RAM (512 MB recommended) 128MB available hard disk space CD-ROM drive Available USB port Downloading Your Files 1. 2. 3. 4. 5. 6. Turn on your camera. Connect the camera to your computer with the USB cable.