MODEL MODÈLE MODELO DISC GRINDER MEULEUSE AMOLADORA ANGULAR G 12SA2 SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool.
CONTENTS English Page IMPORTANT SAFETY INFORMATION ...... 3 MEANINGS OF SIGNAL WORDS .............. 3 SAFETY ........................................................... 4 GENERAL SAFETY RULES ......................... 4 SPECIFIC SAFETY RULES AND SYMBOLS ................................................ 6 DOUBLE INSULATION FOR SAFER OPERATION ............................................ 8 FUNCTIONAL DESCRIPTION ......................... 9 NAME OF PARTS ........................................
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English (5) Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. (6) Use safety equipment. Always wear protective glasses. Dust mask, nonskid safety shoes, hard hat, or ear plugs must be used for appropriate conditions. 4. Tool Use and Care (1) Use clamps or other practical way to secure and support the workpiece to a stable platform.
English SPECIFIC SAFETY RULES AND SYMBOLS 1. ALWAYS use proper guard with depressed center wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3. Hold tools by insulated gripping surfaces when performing an operation where the tool may contact hidden wiring or its own cord.
English 11. Keep all screws, bolts and covers tightly in place. Keep all screws, bolts, and plates tightly mounted. Check their condition periodically. 12. Do not use power tools if the plastic housing or handle is cracked. Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not be used until repaired. 13. Blades and accessories must be securely mounted to the tool. Prevent potential injuries to youself or others.
English 27. ALWAYS follow the instructions contained in this manual when replacing the depressed center wheel. 28. ALWAYS be careful with buried objict such as an underground wiring. Touching these active wiring or electric cable with this tool, you may receive an electric shock. Comfirm if there are any buried object such as electric cable within the wall, floor or ceiling where you are going to operate here after. 29. Definitions for symbols used on this tool V ............. volts Hz ........... hertz A .
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
English ASSEMBLY AND OPERATION APPLICATIONS 䡬 Removal of casting fin and finishing of various type of steel, bronze and aluminum materials and castings. 䡬 Grinding of welded sections or sections cut by means of an acetylene torch. 䡬 Grinding of synthetic resins, slate, brick, marble. WARNING: To avoid the risk of serious injury, NEVER use this grinder with cup wheels and/or saw blades. PRIOR TO OPERATION 1.
English 6. Mounting the wheel guard Be sure to mount the wheel guard at an angle that will protect the operator’s body from injury by a broken wheel piece. [Installing Wheel Guard] 䡬 Slightly loosen the screw on the wheel Locating Pin guard. 䡬 Install the wheel-guard-locating pin in line with the across flats of the packing gland, turn it to the angle suitable for operation, and make adjustment.
English GRINDER OPERATION ON OFF Switch 1. Hold the grinder firmly by its housing and side handle (Fig. 1). The grinder produces a counterforce which must be controlled by firmly holding onto the grinder. 2. Turn the grinder “on”. (Fig. 3) While holding the grinder firmly, use one finger to slide the switch to the “on” position. 3. Use light grinding pressure. Fig. 3 There is no need to press hard when grinding.
English DEPRESSED CENTER WHEEL ASSEMBLY AND DISASSEMBLY WARNING: Never attempt to assemble or disassemble the depressed center wheel, unless the power switch is in the “OFF” position and the electrical cord has been disconnected from the receptacle. 1. Assembly (1) Turn the disc grinder upsidedown so that the spindle is facing upward. (2) Align the oval-shaped indentation of the wheel washer with the notched part of the spindle, then attach them.
English MAINTENANCE AND INSPECTION WARNING: 䢇 Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 䢇 Using cracked, deformed or damaged wheels can lead to wheel breakage and resulting serious injury. 1. Replacing the depressed center wheel Replace the depressed center wheel when it has been worn out to about 2-3/8" (60mm) in external diameter. Confirm that there is no crack or any damage to the depressed center wheel.
English (3) Remove the end of the pig-tail on the carbon brush from the terminal section of brush holder and then remove the carbon brush from the brush holder. (1) Insert the end of the pi-tail of the carbon brush in the terminal section of brush holder. (2) Insert the carbon brush in the brush holder. (3) Use the auxiliary hexagonal wrench or small screwdriver to return the edge of the spring to the head of the carbon brush. (4) Mount the tail cover and tighten the D4 tapping screw. 5.
English ACCESSORIES WARNING: Never use any accessories other than those mentioned below. The use of any accessories other than those mentionded below or attachments not intended for use such as cup wheel, cut-off wheel or saw blade is dangerous and may cause personal injury or property damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI. STANDARD ACCESSORIES 䡬 Depressed center wheel ..............................................................................
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français (3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation est sur la position d’arrêt avant de brancher la machine. Transporter l’appareil avec les doigts sur l’interrupteur d’alimentation ou brancher un outil avec l’interrupteur sur la position marche invite aux accidents. (4) Retirer les clefs d’ajustement ou les commutateurs avant de mettre l’outil sous tension. Une clef qui est laissée attachée à une partie tournante de l’outil peut provoquer une blessure personnelle.
Français REGLES DE SECURITE SPECIFIQUES ET SYMBOLES 1. Se servir systématiquement d’un capot couvre-meule approprié. En effet, le capot couvremeule met l’opérateur à l’abri d’éventuelles projections de fragments de meule cassés. 2. Les accessoires doivent être utilisés à une cadence équivalent au moins à la vitesse de rotation de la meule telle qu’elle est indiquée sur l’étiquette de mise en garde de l’outil.
Français 9. NE JAMAIS utiliser un outil motorisé pour des applications autres que celles spécifiées. NE JAMAIS utiliser un outil motorisé pour des applications autres que celles spécifiées dans le mode d’emploi. 10. Manipuler l’outil correctement Utiliser l’outil de la façon indiquée dans ce mode d’emploi. Ne pas laisser tomber ou lancer l’outil. NE JAMAIS permettre que l’outil soit utilisé par des enfants, des personnes non familiarisées avec son fonctionnement ou un personnel non autorisé. 11.
Français 23. TOUJOURS porter des lunettes des protections conformes aux exigences des dernières révisions du standard ANSI Z87.1. 24. TOUJOURS porter un masque ou un respirateur pour se protéger de la poussière et des particules dangereuses générées pendant l’opération de meulage. 25. TOUJOURS tenir fermement la poignée principale et la poignée latérale lors de l’utilisation de la meuleuse. 26. TOUJOURS réaliser un essai de fonctionnement avant de commencer le meulage.
Français Ne jamais utiliser des solvants, de l’essence ou des diluants sur les parties en plastique; sinon le plastique risquerait de se dissoudre. CONSERVER CES INSTRUCTIONS ET LES METTRE A LA DISPOSITION DES AUTRES UTILISATEURS ET PROPRIETAIRES DE CET OUTIL! 23 G12SA2_2-F.
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français ASSEMBLAGE ET FONCTIONNEMENT UTILISATIONS 䡬 Retrait des ébarbures de moulage et finition de divers type de matériaux en métal, bronze et aluminium ainsi que des moulages. 䡬 Meulage des sections soudées ou des sections coupées à l’acétylène. 䡬 Meulage des résines synthétiques, des ardoises, des briques, du marbre. AVERTISSEMENT: Pour éviter tout risque de blessures graves, NE JAMAIS utiliser cette meuleuse avec des meules-boisseaux et/ou des lames de scie. AVANT L’UTILISATION 1.
Français [Installation du capot couvre-meule] 䡬 Desserrer légèrement la vis du capot couvre-meule. 䡬 Installer la tige de positionnement du capot couvre-meule dans l'axe de la largeur sur le plat du presse-étoupe, la tourner à un angle convenable pour le fonctionnement, et effectuer le réglage. 䡬 Une fois le réglage effectué, vérifier que la vis est bien serrée à fond sur le capot du couvre-meule afin de l'immobiliser complètement. Tige de positionnement Capot couvremeule Aplats en couronne Fig.
Français UTILISATION DE LA MEULEUSE ON OFF Interrupteur 1. Maintenir la meuleuse fermement par son boîtier et sa poignée secondaire (Fig. 1). La meuleuse produit une contre-force qui doit être maîtrisée en la maintenant fermement. 2. Mettre la meuleuse sous tension (Fig. 3) Tout en maintenant la meuleuse fermement, utiliser un doigt pour faire glisser l’interrupteur sur la position “ON”. Fig. 3 3. Utiliser une légère pression de meulage.
Français PRECAUTION: La meule à dépression centrale en rotation crée une turbulence d’air. Ne pas poser la meuleuse dans des endroits poussiéreux ou sales avant qu’elle ne soit complètement arrêtée. ASSEMBLAGE ET DESASSEMBLAGE DE LA MEULE A DEPRESSION CENTRALE AVERTISSEMENT: Ne jamais essayer d’assembler ou de désassembler la meule à dépression centrale si l’interrupteur d’alimentation n’est pas sur la position “OFF” et que le cordon électrique n’est pas débranché de la prise secteur. 1.
Français ENTRETIEN ET INSPECTION AVERTISSEMENT: 䢇 S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspection de la meuleuse. 䢇 L’utilisation d’une meule fissurée, déformée ou endommagée risque de provoquer une rupture de la meule et d’entraîner la mort ou des blessures graves. 1.
Français 䡬 Remplacement d’un balai en carbone: (1) Desserrer la vis taraudeuse D4 qui retient le couvercle arrière pour l’enlever. (2) Utiliser la clé auxiliaire à six pans ou un petit tournevis pour soulever le bord du ressort qui retient le balai en carbone. Retirer le bord du ressort vers l’extérieur Ressort du support du balai.
Français ACCESSOIRES AVERTISSEMENT: Ne jamais utiliser de pièces d’accessoires autres que ceux mentionnés ci-dessous. L’utilisation de tout autre accessoire que ceux mentionnés ci-dessous ou de tout équipement non conçu pour cet outil, tel qu’une meule-boisseau, une meule en cuvette ou une lame de scie est dangereuse et peut provoquer des blessures ou des dommages du matériel. REMARQUE: Les accessoires sont sujets à changement sans obligation de la part de HITACHI.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES. 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español (3) Evite la puesta en marcha accidental. Cerciórese de que la alimentación de la herramienta eléctrica esté desconectada antes de enchufarla en una toma de la red. Si lleva la herramienta eléctrica con el dedo colocado en el interruptor, o si la enchufa con dicho interruptor cerrado, es posible que se produzcan accidentes. (4) Quite las llaves de ajuste y abra los interruptores antes de poner en funcionamiento la herramienta.
Español NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD 1. Emplee siempre un protector adecuado para el disco abombado. 2. Los accesorios deben tener un valor nominal por lo menos para la velocidad recomendada en la etiqueta de advertencia de la herramienta. Los discos y los otros accesorios que funcionan a una velocidad superior a la nominal pueden salir volando y causar daños. 3.
Español tire la herramienta. NO permita NUNCA que los niños ni otras personas no autorizadas ni familiarizadas con la operación de la herramienta utilicen ésta. 11. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 12. No utilice herramientas eléctricas si la carcasa o la empuñadura de plástico está rajada.
Español 24. SIEMPRE utilice una mascarilla para protegerse contra el polvo o las partículas potencialmente dañinos generados durante la operación de la amoladora. 25. SIEMPRE sujete firmemente la empuñadura del cuerpo y la empuñadura lateral cuando utilice la amoladora. 26. SIEMPRE realice una operación de prueba antes de utilizar la amoladora. (Véase “Pruebe la amoladora antes de utilizarla” en la página 41). 27.
Español ¡GUARDE ESTAS INSTRUCCIONES Y PÓNGALAS A DISPOSICIÓN DE OTROS USUARIOS Y PROPIETARIOS DE ESTA HERRAMIENTA! 38 G12SA2_3-Sp.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español MONTAJE Y OPERACIÓN APLICACIONES 䡬 Eliminación de rebabas de piezas fundidas y acabado de varios tipos de materiales y piezas fundidas de acero, bronce, y aluminio. 䡬 Amoladura de secciones soldadas o de secciones cortadas con un soplete oxiacetilénico. 䡬 Amoladura de resinas sintéticas, pizarra, ladrillo, y mármol. ADVERTENCIA: Para evitar el riesgo de lesiones de gravedad, no utilice NUNCA esta amoladora con muelas de cubeta y/u hojas de sierra. ANTES DE LA OPERACIÓN 1.
Español 6. Montaje del protector de la rueda Cerciórese de montar el protector de la rueda con un ángulo que proteja el cuerpo del operador contra lesiones debidas a un trozo de rueda roto. [Instalación del protector de la rueda] 䡬 Afloje ligeramente el tornillo del protector de la rueda. 䡬 Instale el pasador de posicionamiento del protector de la rueda alineándolo con la distancia entre caras del prensaestopas, gírelo a un ángulo adecuado para la operación, y realice el ajuste.
Español OPERACIÓN DE LA AMOLADORA ANGULAR 1. Sujete firmemente la amoladora por su carcasa y la empuñadura lateral (Fig. 1). ON OFF Interruptor La amoladora producirá una contrafuerza que habrá que controlar sujetándola firmemente. 2. Conecte la alimentación de la amoladora. (Fig. 3) Sujetando firmemente la amoladora, utilice un dedo para deslizar el interruptor hasta la posición “ON”. Fig. 3 3. Presione con poca fuerza la amoladora. No es necesario presionar con fuerza para amolar.
Español 6. Ajuste la operación de acuerdo con el acabado deseado. Para realizar un acabado preciso, reduzca la presión levantando ligeramente la amoladora. Realice la operación de amoladura lentamente y con la velocidad apropiada. PRECAUCIÓN: El giro de la rueda de disco abombado creará turbulencia de aire. No coloque la amoladora en áreas de polvo o suciedad hasta que se haya parado completamente.
Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: 䢇 Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 䢇 El uso de ruedas agrietadas, deformadas o dañadas puede ocasionar la rotura de la rueda y lesiones de gravedad. 1. Reemplazo de la rueda de disco abombado Reemplace la rueda de disco abombado cuando se haya desgastado hasta aproximadamente 2-3/8" (60 mm) de diámetro externo.
Español 䡬 Reemplazo de las escobillas (1) Afloje el tornillo autorroscante D4 que sujeta la cubierta de la cola y desmonte ésta. (2) Emplee la llave macho hexagonal auxiliar o un pequeño destornillador para tirar del borde del resorte helicoidal que empuja hacia abajo el carbón de contacto Resorte extraiga el dorde del resorte hacia afuera el soporte del carbón de contacto.
Español ACCESORIOS ADVERTENCIA: No utilice nunca ningún accesorio distinto de los mencionados más abajo. La utilización de cualquier otro accesorio distinto de los mencionados más abajo o no previstos para el uso, como una rueda de copa, una rueda de corte o una hoja de sierra, podría resultar peligroso y causar lesiones o daños materiales. NOTA: Los accesorios están sujetos a cambio sin ninguna obligación por parte de HITACHI. ACCESORIOS ESTÁNDAR 䡬 Rueda de disco abombado ................................
G12SA2_3-Sp.
Español WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber.