Rotary Hammer Bohrhammer Marteau perforateur Martello perforatore Boorhamer Martillo perforador Martelo perfurador DH 24PG • DH 26PB • DH 28PBY DH28PBY Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste istruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.
1 2 4 3 1 4 2 3 4 6 5 4 5 6 7 9 8 7 8 9 2 00Table_DH26PB_WE 2 3/15/13, 14:08 8
9 10 C 4 3 D B 0 A 3 4 2 11 12 E G F 1 13 H 3 4 14 K I M L H J 15 16 O N P K 3 00Table_DH26PB_WE 3 3/15/13, 14:08
17 18 L 4 00Table_DH26PB_WE 4 3/15/13, 14:08
English 1 2 3 4 5 6 7 8 9 0 A B C D E F G H I J K L M N O P Drill bit Part of SDS-plus shank Front cap Grip Dust cup Dust collector (B) Push button Change lever Push button Drill chuck Chuck adapter Chuck adapter (D) Bit Socket Side handle Depth gauge Mounting hole Taper shank adapter Cotter Rest Core bit Core bit shank Thread Center pin Guide plate Core bit tip Deutsch Français Italiano Bohrer Teii des SDS-plus Schaftes Vordere Abdeckung Spannbacke Staubschale Staubfänger (B) Druckschalter Wahlhebel D
Nederlands 1 3 4 5 6 7 8 9 0 Boorstuk Onderdeel van SDS Plus schacht Voorkap Greep Stofvangkap Stofverzamelaar (B) Drukknop Keuzeschakelaar Drukknop Boorkop A Boorkopadaptor B Boorkopadaptor (D) C D E F G I J K Boorstuk Aansluithuls Zijgreep Diepte-maatlat Montagegat Vernauwde schachtadaptor Cotter Steun Kernstuk L Kernstukschacht M N O Schroefdraad Middenpin Pasplaatje P Top van kernstuk 2 H Español Broca Parte delSDS más vástago Cubierta frontal Sujetador Capa de polvo Colector de polvo
Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Symbole WARNUNG Die folgenden Symbole werden für diese Maschine verwendet. Achten Sie darauf, diese vor der Verwendung zu verstehen. Lesen Sie sämtliche Sicherheitshinweise und Anweisungen durch.
English (Original instructions) GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit.
English ROTARY HAMMER SAFETY WARNINGS 1. 2. 3. 4. Wear ear protectors Exposure to noise can cause hearing loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
English OPTIONAL ACCESSORIES (sold separately) Tool Adapters 䢇 Drilling holes in concrete or tile Use on jobs facing upwards Drill bit Dust cup Dust collector (B) 䢇 Drilling anchor holes Rotation + Hammering + Taper shank adapter Drill bit (Taper shank) Cotter 䢇 Large hole boring Guide plate Center pin Core bit shank Core bit 䢇Anchor setting Anchor setting adapter 䢇 Bolt placing operation with Chemical Anchor Hexagon socket Chemical anchor adapter 䢇 Demolishing operation Rotation only
English 䢇 Drilling holes in concrete or tile Outer dia. 3.4 mm 3.5 mm 䢇 Large hole boring Drill bit (slender shaft) Overall length Effective length 90 mm 45 mm SDS-plus Drill bit Outer dia. 4.0 mm 5.0 mm 5.5 mm 6.0 mm 6.4 mm 6.5 mm 7.0 mm 7.5 mm 8.0 mm 8.5 mm 9.0 mm 9.5 mm 10.0 mm 10.5 mm 11.0 mm 12.0 mm 12.5 mm 12.7 mm 13.0 mm 14.0 mm 14.3 mm 14.5 mm 15.0 mm 16.0 mm 16.5 mm 17.0 mm 17.5 mm 18.0 mm 19.0 mm 20.0 mm 22.0 mm 24.0 mm 25.
English APPLICATIONS Rotation and hammering function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile Rotation only function 䡬 Drilling in steel or wood (with optional accessories) 䡬 Tightening machine screws, (with optional accessories) wood screws PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate. 2. Power switch Ensure that the power switch is in the OFF position.
English 3. Rotation only This rotary hammer can be set to rotation only mode by pressing the push button and turning the change lever to the mark (Fig. 8). To drill wood or metal material using the drill chuck and chuck adapter (optional accessories), proceed as follows. Installing drill chuck and chuck adapter (Fig. 9). (1) Attach the drill chuck to the chuck adapter. (2) The part of the SDS-plus shank is the same as the drill bit. Therefore, refer to the item of “Mounting the drill bit” for attaching it.
English LUBRICATION GUARANTEE Low viscosity grease is applied to this rotary hammer so that it can be used for a long period without replacing the grease. Replace the grease whenever you change the carbon brush to maintain the service life. Further use of the rotary hammer with lock off grease will cause the machine to seize up reduce the service life. CAUTION A special grease is used with this machine, therefore, the normal performance of the machine may be badly affected by use of other grease.
English The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure. WARNING 䡬 The vibration emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used.
Deutsch (Übersetzung der Original-Gebrauchsanweisung) ALLGEMEINE SICHERHEITSHINWEISE FÜR ELEKTROGERÄTE WARNUNG Lesen Sie sämtliche Sicherheitshinweise und Anweisungen durch Wenn die Warnungen und Anweisungen nicht befolgt werden, kann es zu Stromschlag, Brand und/oder ernsthaften Verletzungen kommen. Bitte bewahren Sie alle Warnhinweise und Anweisungen zum späteren Nachschlagen auf.
Deutsch Bei Beschädigungen lassen Sie das Elektrowerkzeug reparieren, ehe Sie es benutzen. Viele Unfälle mit Elektrowerkzeugen sind auf schlechte Wartung zurückzuführen. f) Halten Sie Schneidwerkzeuge scharf und sauber. Richtig gewartete Schneidwerkzeuge mit scharfen Schneidkanten bleiben weniger häufig hängen und sind einfacher zu beherrschen.
Deutsch SONDERZUBEHÖR (separat zu beziehen) Werkzeuges Adapter 䢇 Bohren von Löchern in Beton oder Fliesen Bei nach oben gerichteten Arbeiten verwenden Bohrer Staubschale Staubfang (B) Drehen und Hämmern 䢇 Bohren von Ankerlöchern Durchmesser + Konusschaftadapter Bohrer (Kegelschaft) Dorn 䢇 Lochbohren mit weitem Durchmesser Führungsplatte Mittelstift Bohrkrone Bohrkronenschenkel 䢇Ankereinsatz Adapter für Ankerbefestigung 䢇 Bolzenplazierung für Chemical Anchor Adapter für Chemical Anchor Se
Deutsch 䢇 Bohren von Löchern in Beton oder Fliesen Außendurchm. 3,4 mm 3,5 mm Bohrer (dünner Schaft) Gesamtlänge Arbeitslänge 90 mm 45 mm SDS-plus-Bohrer Außendurchm.
Deutsch ANWENDUNGEN Dreh- und Hämmerfunktion 䡬 Bohren von Ankerlöchern 䡬 Bohren von Löchern in Beton 䡬 Bohren von Löchern in Kachel Nur Drehbohrfunktion 䡬 Bohren in Stahl oder Holz (mit Sonderzubehör) 䡬 Anziehen von Maschinenschrauben, Holzschrauben (mit Sonderzubehör) VOR INBETRIEBNAHME 1. Netzspannung Prüfen, daß die zu verwendende Netzspannung der Angabe auf dem Typenschild entspricht. 2. Netzschalter Prüfen, daß der Nezschalter auf „AUS” steht.
Deutsch ACHTUNG Wenn der Bohrer mit Baueisenstangen in Berührung kommt, stoppt sofort der Bohren, und nur der Bohrhammer dreht sich. Deshalb den Handgriff gut fest halten wie in Abb. 7 gezeigt. 3. Nur Drehbohren Dieser Bohrhammer kann durch Druck auf den Druckknopf und Drehen des Umschalthebels zur Markierung auf Betrieb nur für Bohren eingestellt werden (Abb. 8). Zum Bohren von Holz und Metall einen Bohrfutteradapter und ein Bohrfutter (zubehör) verwenden.
Deutsch ACHTUNG Vor entfernung des Zentrierstifts und der Führungsplate das Gerät ausschalten und von der Steckdose trennen. 3. Entfernung (Abb. 18) Für die Entfernung kann ebenfalls ein anderes Verfahren angewandt werden. Den Bohrkronenzapfen vom Bohrhammer eintfernen und mit einem Hammer mehrmals kräftig auf den Kopf des Bohrkronenzapfens schlagen. Dabei sollte allerdings die Bohrkrone festgehalten werden. Dann löst sich das Gewinde und die Bohrkrone kann abgenommen werden.
Deutsch Information über Betriebslärm und Vibration Die gemessenen Werte wurden entsprechend EN60745 bestimmt und in Übereinstimmung mit ISO 4871 ausgewiesen. Gemessener A-gewichteter Schallpegel: 100 dB (A) (DH24PG) 101 dB (A) (DH26PB) 100 dB (A) (DH28PBY) Gemessener A-gewichteter Schalldruck: 91 dB (A) 89 dB (A) (DH24PG) 90 dB (A) (DH26PB) 89 dB (A) (DH28PBY) Messunsicherheit KpA: 3 dB (A) Gehörschutz tragen. Gesamtvibrationswerte (3-Achsen-Vektorsumme), bestimmt gemäß EN60745.
Français (Traduction des instructions d'origine) AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX POUR L’OUTIL AVERTISSEMENT Lire tous les avertissements de sécurité et toutes les instructions. Ne pas suivre les avertissements et instructions peut donner lieu à un choc électrique, un incendie et/ou une blessure sérieuse. Conserver tous les avertissements et toutes les instructions pour pouvoir s'y reporter ultérieurement.
Français f) Garder affûtés et propres les outils permettant de couper. Des outils destinés à couper correctement entretenus avec des pièces coupantes tranchantes sont moins susceptibles de bloquer et sont plus faciles à contrôler. g) Utiliser l’outil, les accessoires et les lames etc., conformément à ces instructions, en tenant compte des conditions de travail et du travail à réaliser.
Français ACCESSOIRES EN OPTION (vendus séparément) L’outil Adaptateurs 䢇 Percer des trous dans du béton ou un carreau Utiliser pour les travaux redressés Capuchon anti Collecteur à poussière poussière (B) Foret de perçage 䢇 Perçage de trous d’ancrage Rotation + percussion + Foret de perçage (queue conique) Raccord de queue conique Clavette 䢇 Perçage de trou à large diamètre Plaque centrale Goujon de guidage Couronne Queue de couronne 䢇Mise en place de la fixation Raccord de mise en place de l
Français 䢇 Percer des trous dans du béton ou un carreau Foret de perçage (Tige fine) Dia. extérieur Longueur totale Longueur effective 3,4 mm 90 mm 45 mm 3,5 mm Foret de perçage SDS-plus Dia.
Français APPLICATIONS Fonction de rotation et percussion 䡬 Perçage de trous d’ancrage 䡬 Perçage de trous dans béton 䡬 Perçage de trous dans une tuile Par action de rotation uniquement 䡬 Perçage de l’acier ou du bois (avec accessoires en option) 䡬 Serreage de vis mécaniques et de vis à bois (avec accessoires en option) 䡬 䡬 AVANT LA MISE EN MARCHE 1. Source de puissance S’assurer que la source de puissance à utiliser correspond à la puissance indiquée sur la plaque signalétique du produit. 2.
Français (3) Il n’est pas du tout nécessaire d’appliquer une forte pression sur la perceuse. Il suffit d’appliquer une légère pression de manière à ce que la poussière et les éclats soient déchargés progressivement. ATTENTION Quand le foret de perçage touche une poutre en fer, la mèche s’arrête immédiatement et la perceuse réagit en tournant. Par conséquent, tenir fermement la poignée principale et la poignée latérale, comme indiqué à la Fig. 7. 3.
Français (3) Quand on a percé sur une profondeur d’environ 5 mm, la position du trou est déterminée. Continuer à percer après avoir retiré le goujon central et la plaque de guidage de la couronne. (4) Si l’on applique une force excessive, cela donnera un travail bâclé et abîmera la pointe du foret de perçage, réduisant ainsi la durée de service de la perceuse à percussion.
Français La valeur totale des vibrations a été mesurée par une méthode d’essai standard et peut être utilisée pour comparer un outil à un autre. Elle peut également être utilisée pour une évaluation préliminaire du niveau d’exposition. AVERTISSEMENT 䡬 La valeur d’émission de vibration en fonctionnement de l’outil électrique peut être différente de la valeur totale déclarée, en fonction des utilisations de l’outil.
Italiano (Traduzione delle istruzioni originali) AVVERTIMENTI GENERALI DI SICUREZZA SUGLI UTENSILI ELETTRICI AVVERTENZA Leggere tutti gli avvertimenti di sicurezza e tutte le istruzioni. La mancata osservanza degli avvertimenti e delle istruzioni potrebbe essere causa di scosse elettriche, incendi e/o gravi lesioni. Salvare tutti gli avvertimenti e le istruzioni per riferimenti futuri.
Italiano f) Mantenere gli strumenti di taglio affilati e puliti. Gli strumenti di taglio in condizioni di manutenzione adeguata, con bordi affilati, sono meno soggetti al bloccaggio e sono più facilmente controllabili. g) Utilizzare l'elettroutensile, gli accessori, le barrette, ecc. in conformità a quanto riportato nelle presenti istruzioni, tenendo in debita considerazione le condizioni operative e il tipo di lavoro da eseguire.
Italiano ACCESSORI DISPONIBILI A RICHIESTA (venduti separatamente) Utensili Adattatori 䢇 Trapanatura di fori calcestruzzo o piastrelle in Usare su lavori rivolto verso l’alto Camera a polvere (B) Contenitore a polvere Punta 䢇 Foratura per ancoraggio Rotazione e martellamento + Broca de taladro (vástago cónico) Adaptador cónico Coppiglia 䢇 Forature ad ancoraggio Punta della Piastra guida corona Corona Gambo della corona 䢇Ancoraggio Adattatore per ancoraggio 䢇 Operazioni di perforazione de
Italiano 䢇 Trapanatura di fori in calcestruzzo o piastrelle Diametro esterno 3,4 mm 3,5 mm Punta (Albero sottile) Lunghezza totale Lunghezza effettiva 90 mm 45 mm Punta trapano SDS-plus Diametro esterno 4,0 mm 5,0 mm 5,5 mm 6,0 mm 6,4 mm 6,5 mm 7,0 mm 7,5 mm 8,0 mm 8,5 mm 9,0 mm 9,5 mm 10,0 mm 10,5 mm 11,0 mm 12,0 mm 12,5 mm 12,7 mm 13,0 mm 14,0 mm 14,3 mm 14,5 mm 15,0 mm 16,0 mm 16,5 mm 17,0 mm 17,5 mm 18,0 mm 19,0 mm 20,0 mm 22,0 mm 24,0 mm 25,0 mm Lunghezza totale 110 mm 110 mm 160 mm 110 mm 110 mm
Italiano APPLICAZIONI Funzione di rotazione e martellamento 䡬 Apertura di fori da ancoraggio 䡬 Apertura di fori nel cemento armato 䡬 Apertura di fori in tegole Con sola rotazione 䡬 Foratura di acciaio o legno (con accessori disponibili a richiesta) 䡬 Viti di fissaggio per macchine, viti del legn (con accessori disponibili a richiesta) PRIMA DI INIZIARE LE OPERAZIONI 1.
Italiano (3) Non è assolutamente necessario eserciatare una grande forza sul trapano. Spingere invece il trapano solo leggermente, in modo che si veda la polvere uscire dal foro. ATTENZIONE Se la punta, durante la penetrazione nel materiale, dovesse incontrare del ferro, essa portrebbe avere la tendenza a fermarsi (non può girare), il che causerebbe a sua volta la tendenza del trapano a girare in senso opposto.
Italiano (4) Esercitando unaforza eccessiva sul trapano, durante la foratura, non si aumenta la velocità di esecuzione del lavoro, ma si causa soltanto il più veloce consumo della punta e la diminuzione della durata del trapano. ATTENZIONE Prima di togliere la punta della corona e la piastra guida spegnere l’apparecchio e levare la spina dalla presa di rete. 3. Smontaggio (Fig.
Italiano Il valore totale di emissione vibrazioni dichiarato è stato misurato in base al metodo di test standard e può essere utilizzato per confrontare un utensile con un altro. Può essere inoltre utilizzato per la stima preliminare dell’esposizione. AVVERTENZA 䡬 Il valore di emissione vibrazioni durante l’uso effettivo dell’utensile può essere diverso dal valore totale dichiarato in base alle modalità di utilizzo dell’utensile stesso.
Nederlands (Vertaling van de oorspronkelijke aanwijzingen) ALGEMENE VEILIGHEIDSWAARSCHUWINGEN VOOR ELEKTRISCH GEREEDSCHAP WAARSCHUWING Lees alle waarschuwingen en instructies aandachtig door. Nalating om de waarschuwingen en instructies op te volgen kan in een elektrische schok, brand en/of ernstig letsel resulteren. Bewaar alle waarschuwingen en aanwijzingen voor eventuele naslag in de toekomst.
Nederlands Slecht onderhouden elektrisch gereedschap is verantwoordelijk voor een groot aantal doe-het-zelf ongelukken. f) Houd snijwerktuigen scherp en schoon. Goed onderhouden snijwerktuigen met scherpe snijranden lopen minder snel vast en zijn gemakkelijker in het gebruik. g) Elektrisch gereedschap, toebehoren, bits enz. moeten in overeenstemming met deze instructies worden gebruikt waarbij de werkomstandigheden en het werk in overweging moeten worden genomen.
Nederlands EXTRA TOEBEHOREN (los te verkrijen) Gereedschap Adapters Zorg ervoor dat het gereedschap tijdens het klussen naar boven wijst 䢇 In beton of tegels boren Boorstuk Stofvangkap Stofverzamelaar (B) 䢇Boren van ankergaten + Draaien + hameren Boorstuk (vernauwde schacht) Vernauwde schachtadaptor Cotter 䢇 Gat met grote diameter boren Pasplaatje Middenpin Kernstuk Kernstukschacht 䢇Bepalen van anker Ankerstellingsadaptor 䢇 Bout-aanbrengwerk voor chemische anker Zeskant Chemische ankerada
Nederlands 䢇 In beton of tegels boren 䢇 Gat met grote diameter boren Boorstuk (smalle as schacht) Buitendiameter Totale lengte Effektieve lengte 3,4 mm 90 mm 45 mm 3,5 mm SDS-plus boorbit Buitendiameter 4,0 mm 5,0 mm 5,5 mm 6,0 mm 6,4 mm 6,5 mm 7,0 mm 7,5 mm 8,0 mm 8,5 mm 9,0 mm 9,5 mm 10,0 mm 10,5 mm 11,0 mm 12,0 mm 12,5 mm 12,7 mm 13,0 mm 14,0 mm 14,3 mm 14,5 mm 15,0 mm 16,0 mm 16,5 mm 17,0 mm 17,5 mm 18,0 mm 19,0 mm 20,0 mm 22,0 mm 24,0 mm 25,0 mm Totale lengte 110 mm 110 mm 160 mm 110 mm 110 mm 160
Nederlands TOEPASSINGEN Draaien en hameren 䡬 Boren van ankergaten 䡬 Boren van gaten in beton 䡬 Boren van gaten in tegels Alleen draaien 䡬 Boren in staal of hout (met los verkrijgbare toebehoren) 䡬 Vastdraaien van machine-schroeven, houtschroeven (met los verkrijgbare toebehoren) VOOR HET GEBRUIK 1. Netspanning Controleren of de netspanning overeenkomt met de opgave op het naamplaatje. 2. Netschakelaar Controleren of de netschakelaar op „UIT” staat.
Nederlands LET OP Als het boorstuk vast komt te zitten in een ijzeren stang, kan de boorhamer hevi gaan schudden. Zorg er daarom voor dat beide handgrepen goed worden vastgehouden zoals aangegeven in Afb. 7. 3. Alleen draaien Door op de druktoets te drukken en de keuzehendel naar de markering te draaien, kan deze boorhamer in de functie voor uitsluitend roteren worden gesteld (Afb. 8). Ga als volgt te werk voor het boren in hout of metaal met behulp van de boorkop en boorkopadaptor (extra toebehoren).
Nederlands 3. Demonteren (Afb.18) Neem de kernstukschacht uit de boorhamer en sla twee of drie keer hard met een hamer op de kop van de kernstukschacht. Het kernstuk kan nu verwijderd worden. MODIFICATIES Hitachi elektrisch gereedschap wordt voortdurend verbeterd en gewijzigd teneinde gebruik te kunnen maken van de nieuwste technische ontwikkelingen. Daarom is mogelijk dat sommige onderdelen zonder voorafgaande kennisgeving gewijzigd worden.
Nederlands De totale bepaalde trillingswaarde is gemeten in overeenstemming met een standaardtestmethode en is bruikbaar om meerdere gereedschappen met elkaar te vergelijken. U kunt dit ook als beoordeling vooraf aan de blootstelling gebruiken. WAARSCHUWING 䡬 De trillingsemissiewaarde tijdens het feitelijke gebruik van het elektrisch gereedschap kan afwijken van de opgegeven totale waarde afhankelijk van de manieren waarop het gereedschap wordt gebruikt.
Español (Traducción de las instrucciones originales) ADVERTENCIAS DE SEGURIDAD GENERAL DE LA HERRAMIENTA ELÉCTRICA ADVERTENCIA Lea todas las instrucciones y advertencias de seguridad. Si no se siguen las advertencias e instrucciones, podría producirse una descarga eléctrica, un incendio y/o daños graves. Guarde todas las advertencias e instrucciones para futura referencia.
Español Se producen muchos accidentes por no realizar un mantenimiento correcto de las herramientas eléctricas. f) Mantenga las herramientas de corte afiladas y limpias. Las herramientas de corte correctamente mantenidas con los bordes de corte afilados son más fáciles de controlar. g) Utilice la herramienta eléctrica, los accesorios y las brocas de la herramienta, etc. de acuerdo con estas instrucciones, teniendo en cuenta las condiciones laborales y el trabajo que se va a realizar.
Español ACCESORIOS FACULTATIVOS (de venta por separado) Herramienta Adaptadores 䢇 Perforación de agujeros en cemento o losa Utilizar en trabajos colocados hacia arriba Broca de taladro Copa de polvo Colector de polvo (B) 䢇 Taladrar orificios de anclaje Rotación + golpeteo + Broca de taladro (Vástago cónico) Adaptador cónico Chaveta 䢇 Perforación de orificio de diámetro grande Placa guia Pasador central Barrena tubular Espiga de la barrena tubular 䢇 Montaje de ancla Adaptador de montaje de an
Español 䢇 Perforación de agujeros en cemento o losa Diám. externo 3,4 mm 3,5 mm Diám.
Español APPLICACION Rotación y función de golpeteo 䡬 Perforación de orificios de anclaje 䡬 Perforación de orificios de hormigón 䡬 Perforación de orificios de baldosa Rotación solamente 䡬 Perforación de orificios en hormigón o madera (con accesorios facultativos) 䡬 Apretar tornillos en metal o madera (con accesorios facultativos) ANTES DE LA PUESTA EN MARCHA 1.
Español la punta de la broca en la posición para taladrar (Fig. 7). (3) No es necesario presionar con fuerza la broca. Presionar ligeramente la broca de forma que el polvo producido al taladrar salga al exterior gradualmente. PRECAUCIÓN Cuando la broca toque una barra de hierro de construción se detendrá inmediatamente y el martillo perforador tenderá a girar. Por lo tanto, sujetar el mango lateral y sostenerlo firmemente como se ilustra en la Fig. 7. 3.
Español y seguir taladrando. (4) La aplicación de una fuerza excesiva acelerará el cumplimiento del trabajo, pero deteriorará la punta de la broca reduciendo la duración del martillo perforador. PRECAUCIÓN Cuando se quite el pasador central y la placa guía, poner el interruptor en la posición de apagado (OFF) y desconectar el enchufe de la toma de alimentación. 3. Desmontaje (Fig.
Español El valor total de vibración declarado ha sido medido de acuerdo con un método de prueba estándar y permite comparar unas herramientas con otras. También resulta útil para llevar a cabo evaluaciones preliminares de exposición. ADVERTENCIA 䡬 La emisión de vibración durante la utilización de la herramienta eléctrica puede ser diferente del valor total declarado dependiendo de las formas de utilización de la herramienta.
Português (Tradução das instruções originais) AVISOS GERAIS DE SEGURANÇA PARA A FERRAMENTA ELÉCTRICA AVISO Leia todas as instruções e avisos de segurança. Se não seguir todas as instruções e os avisos, pode provocar um choque eléctrico, incêndio e/ou ferimentos graves. Guarde todos os avisos e instruções para referência futura. O termo “ferramenta eléctrica” em todos os avisos referese à sua ferramenta ligada à corrente (com fios) ou à ferramenta eléctrica a baterias (sem fios).
Português f) Mantenha as ferramentas de corte afiadas e limpas. As ferramentas de corte com uma manutenção adequada e extremidades afiadas são menos propensas a dobrar e mais fáceis de controlar. g) Utilize a ferramenta eléctrica, acessórios e pontas de ferramentas, etc., de acordo com estas instruções, tomando em consideração as condições de trabalho e o trabalho a ser efectuado. A utilização de uma ferramenta eléctrica para operações diferentes das concebidas pode resultar num mau funcionamento.
Português ACESSÓRIOS OPCIONAIS (vendidos separadamente) Ferramenta Adaptadores 䢇 Perfurar em cimento ou azulejos Utilize em trabalhos virados para cima Broca Receptáculo de poeira Coletor de poeira (B) 䢇 Perfuração de furos para ancoragem de tubos Rotação e martelagem + Adaptador de cabo cônico Broca (cabo cônico) Cavilha 䢇 Perfuração de furos grandes Cabo de coroa Placa-guia Pino central Coroa 䢇 Montagem de âncora Adaptador de montagem de âncora 䢇 Operação de colocação de parafuso com Ânc
Português 䢇 Perfurar em cimento ou azulejos 䢇 Perfuração de furos grandes Broca (haste delgada) Dia. exterior Comprimento total Comprimento efetivo 3,4 mm 90 mm 45 mm 3,5 mm Broca SDS-plus Dia.
Português APLICAÇÕES Função de rotação e martelagem 䡬 Fazer furos ancorados 䡬 Fazer furos em concreto 䡬 Fazer furos em azulejo Função de rotação apenas 䡬 Perfurar em aço ou madeira (com acessórios opcionais) 䡬 Apertar parafusos para metal, parafusos de madeira (com acessórios opcionais) ANTES DA OPERAÇÃO 1. Fonte de energia Certifique-se de que a fonte de energia a ser utilizada está conforme às exigências especificadas na placa identificadora do produto. 2.
Português CUIDADO Quando a broca toca a barra de ferro da construção, ela pára imediatamente e o martelo perfurador reagirá tendo um movimento de rotação. Portanto, segure com firmeza a empunhadura e a empunhadura lateral, como mostra a Fig. 7. 3. Somente rotação Este martelo perfurador pode ser ajustado para o modo de somente rotação pressionando-se o seletor e girando a alavanca de mudança até a marca (Fig. 8).
Português 3. Desmontagem (Fig. 18) Retire o cabo de coroa do martelo perfurador e martele duas ou três vezes com força a cabeça do cabo de coroa segurando a coroa. A rosca, então, se afrouxa e a coroa pode ser retirada. MODIFICAÇÃO As Ferramentas Elétricas da Hitachi estão sempre sendo aperfeiçoadas e modificadas para incorporar os mais recentes avanços tecnológicos. Dessa forma, algumas peças podem mudar sem aviso prévio.
Português O valor total de vibração declarado foi medido de acordo com um método de teste padrão e pode ser utilizado para comparar ferramentas. Pode também ser utilizado numa avaliação preliminar de exposição. AVISO 䡬 O valor de emissão de vibrações durante a utilização da ferramenta eléctrica pode ser diferente do valor total declarado, consoante as formas de utilização da ferramenta.
08Back_DH24PG_26PB_WE 64 4/8/13, 11:26 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Part Name FRONT CAP STOPPER RING GRIP BALL HOLDER HOLDER PLATE HOLDER SPRING GEAR COVER NAME PLATE OIL SEAL BALL BEARING 6805DD PUSHING BUTTON PUSHING SPRING CHANGE LEVER O-RING (S-18) HITACHI LABEL SPRING(E) BALL BEARING 608VVC2PS2L BEARING WASHER STEEL BALL D7.00 CYLINDER PIN D2.
08Back_DH24PG_26PB_WE 65 4/8/13, 11:26 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Part Name FRONT CAP STOPPER RING GRIP BALL HOLDER HOLDER PLATE HOLDER SPRING GEAR COVER NAME PLATE OIL SEAL BALL BEARING 6805DD PUSHING BUTTON CHANGE LEVER PUSHING SPRING O-RING (S-18) HITACHI LABEL SPRING(E) BALL BEARING 608VVC2PS2L BEARING WASHER STEEL BALL D7.00 CYLINDER PIN D2.
08Back_DH24PG_26PB_WE 66 4/8/13, 11:26 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Part Name FRONT CAP STOPPER RING GRIP BALL HOLDER HOLDER PLATE HOLDER SPRING GEAR COVER NAME PLATE OIL SEAL BALL BEARING 6805DD PUSHING BUTTON CHANGE LEVER PUSHING SPRING O-RING (S-18) HITACHI LABEL SPRING(E) BALL BEARING 608VVC2PS2L BEARING WASHER STEEL BALL D7.00 CYLINDER PIN D2.
English Nederlands GARANTIEBEWIJS GUARANTEE CERTIFICATE 1 2 3 4 5 Model No. Serial No. Date of Purchase Customer Name and Address Dealer Name and Address (Please stamp dealer name and address) Deutsch 1 2 3 4 5 Español CERTIFICADO DE GARANTIA GARANTIESCHEIN 1 2 3 4 5 Modell-Nr. Serien-Nr.
1 2 3 4 ✄ 5 68 08Back_DH24PG_26PB_WE 68 4/8/13, 11:26
Hitachi Power Tools Europe GmbH Siemensring 34, 47877 willich 1, F. R. Germany Tel: +49 2154 49930 Fax: +49 2154 499350 URL: http://www.hitachi-powertools.de Hitachi Power Tools Netherlands B. V. Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040 Fax: +31 30 6067266 URL: http://www.hitachi-powertools.nl Hitachi Power Tools (U. K.) Ltd. Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom Tel: +44 1908 660663 Fax: +44 1908 606642 URL: http://www.hitachi-powertools.co.
08Back_DH24PG_26PB_WE 70 4/8/13, 11:26
08Back_DH24PG_26PB_WE 71 4/8/13, 11:26
Nederlands English Object of declaration: Hitachi Rotary Hammer DH24PG, DH26PB, DH28PBY EC DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with standards or standardization documents EN60745-1, EN60745-2-6, EN55014-1, EN55014-2, EN61000-32 and EN61000-3-3 in accordance with Directives 2004/108/EC and 2006/42/EC. This product also conforms to RoHS Directive 2011/65/EU. The European Standards Manager at Hitachi Koki Europe Ltd.