MODEL MODÈLE MODELO DH 24PC ROTARY HAMMER MARTEAU ROTATIF MARTILLO GIRATORIO INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS WARNING Improper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual before operating the power tool. Please keep this manual available for others before they use the power tool.
English English CONTENTS Page IMPORTANT INFORMATION ............. 3 MEANINGS OF SIGNAL WORDS ...... 3 SAFETY ................................................... 4 GENERAL SAFETY RULES ................. 4 SPECIFIC SAFETY RULES AND SYMBOLS ..... 7 DOUBLE INSULATION FOR SAFER OPERATION ..................................... 8 Page ASSEMBLY AND OPERATION ............ 10 APPLICATIONS ................................. 10 PRIOR TO OPERATION ..................... 10 HOW TO USE ...................................
English IMPORTANT INFORMATION Read and understand all of the operating instructions, safety precautions and warnings in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English (2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. (3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. (4) Remove adjusting keys or wrenches before turning the tool on.
English (2) When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instruction may create a risk of electric shock or injury. 6. Never touch moving parts. Never place your hands, fingers or other body parts near the tool’s moving parts. 7. Never operate without all guards in place. Never operate this tool without all guards or safety features in place and in proper working order.
English 17. Never leave tool running unattended. Turn power off. Don’t leave tool until it comes to a complete stop. 18. Carefully handle power tools. Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged. 19. Do not wipe plastic parts with solvent. Solvents such as gasolie, thinner, benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents.
English DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words and “Double insulation” appear on the power tool or on the nameplate.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool. NAME OF PARTS Nameplate Housing Depth Gauge Drill Bit Lock button Front Cap Grip Change Lever Push Lever button Side Handle Handle Switch Fig.
English ASSEMBLY AND OPERATION APPLICATIONS Rotation and striking function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile Rotation only function 䡬 Drilling in steel or wood (with optional accessories). 䡬 Tightening machine screws, wood screws (with optional accessories). Striking only function 䡬 Light-duty chiselling of concrete, groove digging and edging. PRIOR TO OPERATION 1.
English 6. Mounting the drill bit (Fig. 2) (1) To attach a drill bit (SDS-plus shank), fully pull the grip in the direction of the Front cap Part of SDS-plus shank arrow as shown in Fig. 2 and insert the drill bit as far as it will go while manually turning. (2) By releasing the grip, the drill bit will Grip Drill bit be secured. (3) To remove the drill bit, fully pull the grip Fig. 2 in the direction of the arrow and pull out the drill bit. 7.
English bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length. 䡬 Dump particles after every two or three holes when drilling. 䡬 Please replace the drill bit after removing dust collector (B). 8. Selecting the driver bit Screw heads or bits will be damaged should an inappropriate bit for the screw diameter be employed to drive in the screws. 9. Confirm the direction of bit rotation (Fig.
English CAUTION: 䡬 When the drill bit touches an iron reinforcing rod, the bit will stop immediately and the rotary hammer will react to revolve. Therefore please grip the side handle and handle tightly as shown in Fig. 7. Push button Change Lever 3. Rotation only This rotary hammer can be set to rotation only mode by pressing the push button and turning the change lever to mark. (Fig. 8) To drill a wood or metal material using the separately sold drill chuck and chuck adaptor, proceed as follows.
English CAUTION: 䡬 Exercise care not to excessively prolong driving time, otherwise, the screws may be damaged by excessive force. 䡬 Apply the rotary hammer perpendicularly to the screw head when driving a screw; otherwise, the screw head or bit will be damaged, or driving force will not be fully transferred to the screw. 䡬 Do not attempt to use the rotary hammer in the rotation and striking function with chuck adaptor (D) and bit attached. 5. When driving wood screws (Fig.
English 7. Using depth gauge (Fig. 14) (1) Loosen the knob on the side handle, and insert the depth gauge into the mounting hole on the side handle. (2) Adjust the depth gauge position according to the depth of the hole and tighten the knob bolt securely. Grip 8. How to use the drill bit (taper shank) and the taper shank adaptor. (1) Mount the taper shank adaptor to the rotary hammer. (Fig. 15) (2) Mount the drill bit (taper shank) to the taper shank adaptor. (Fig.
English HOW TO USE THE CORE BIT (FOR LIGHT LOAD) When boring penetrating large hole use the core bit (for light load). At that time use with the center pin and the core bit shank provided as optional accessories. 1. Mounting CAUTION: 䡬 Be sure to turn power OFF and disconnect the plug from the receptacle. (1) Mount the core bit to the core bit shank. (Fig. 17) Lubricate the thread of the core bit shank to facilitate disassembly. (2) Mount the core bit shank to the rotary hammer. (Fig.
English (4) Application of excessive force will not only expedite the work, but will deteriorate the tip edge of the drill bit, resulting in reduced service life of the rotary hammer. CAUTION: 䡬 When removing the center pin and the guide plate, turn OFF the switch and disconnect the plug form the receptacle. 3. Dismounting. (Fig.
English MAINTENANCE AND INSPECTION WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened.
Français INFORMATIONS IMPORTANTES Lire et comprendre toutes les instructions de fonctionnement, les précautions de sécurité et les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SECURITE REGLES GENERALE DE SECURITE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français (2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties mobiles. Les vêtements larges, les bijoux et les cheveux longs peuvent se prendre dans les parties mobiles. (3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation est sur la position d’arrêt avant de brancher la machine.
Français (2) Lors de la réparation d’un outil, utiliser uniquement des pièces de rechange identiques. Suivre les instructions de la section d’entretien de ce mode d’emploi. L’utilisation de pièces non autorisées ou un non respect des instructions d’entretien peut créer un risque d’électrocution ou de blessures. 6. Ne jamais toucher les parties mobiles. Ne jamais placer ses mains, ses doigts ou toute autre partie de son corps près des parties mobiles de l’outil. 7.
Français 16. Ne jamais utiliser un outil défectueux ou qui fonctionne anormalement. Si l’outil n’a pas l’air de fonctionner normalement, fait des bruits étranges ou sans cela paraît défectueux, arrêter de l’utiliser immédiatement et le faire réparer par un centre de service Hitachi autorisé. 17. Ne jamais laisser fonctionner l’outil sans surveillance. Le mettre hors tension. Ne pas abandonner l’outil avant qu’il ne soit complètement arrêté. 18. Manipuler l’outil motorisé avec précaution.
Français DOUBLE ISOLATION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus sûr de cet outil motorisé, HITACHI a adopté une conception à double insolation. “Double isolation” signifie que deux systèmes d’isolation physiquement séparés ont été utilisés pour isoler les matériaux conducteurs d’électricité connectés à l’outil motorisé à partir du cadre extérieur manipulé par l’utilisateur.
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS Par action combinée de rotation et de frappe 䡬 Perçage de trous d’ancrage 䡬 Perçage de trous dans béton 䡬 Perçage de trous dans une tuile Par action de rotation uniquement 䡬 Perçage de l’acier ou du bois (avec accessoires en option) 䡬 Serreage de vis mécaniques et de vis à bois. (avec accessoires en option) Par action de percussion uniquement 䡬 Travaux légers de burinage de béton, de creusage de rainure et de cassure des angles. AVANT L’UTILISATION 1.
Français 6. Montage du foret de perçage (Fig. 2) (1) Pour fixer un foret de perçage (tige SDS plus), tirer complètement l’attache coulissante dans le sens de la flèche, comme indiqué sur la Fig. 2, puis insérer le foret tout en le faisant tourner jusqu’à ce qu’il atteigne le fond. (2) Lorsque l’attache coulissante est relâchée, le foret est fixé. (3) Pour retirer le foret de perçage, tirer complètement l’attache coulissante dans le sens de la flèche et sortir le foret. 7.
Français 䡬 Insérer le collecteur à poussière (B) à fond dans le mandrin de l’appareil principal particules pour ne utilisation pluse facile. 䡬 Lors de la mise sous tension du marteau rotatif alors le collecteur à poussière (B) est détaché de la surface en béton, le collecteur à poussière (B) va tourner en même temps que le foret. Ne bien activer l’interrupteur de mise sous tension qu’après avoir appuyé le collecteur à poussière (B) sur la surface en béton.
Français Sélecteur 2. Rotation + frappe Cette perceuse à percussion peut être mise sur le mode de rotation et frappe en appuyant sur le bouton pressoir et en tournant le sélecteur vers le repère . (Fig. 6) (1) Monter le foret de perçage. (2) Tirer l’interrupteur de déclenchement après avoir appliqué la pointe du foret sur la position de perçage désirée. (Fig. 7) (3) Il n’est pas du tout nécessaire d’appliquer une forte pression sur le marteau rotatif.
Français PRECAUTION: 䡬 Si l’on applique une force excessive, cela donnera un travail bâclé et abîmera la pointe du foret de perçage, réduisant ainsi la durée de service de le marteau rotatif. 䡬 La pointe du foret de perçage risque de se casser quand on dégage la perceuse coincée d’un trou qui vient d’être percé. Par conséquent, pour dégager la perceuse il est important de faire très attention et de relâcher la pression ou de tourner le foret dans le sens contraire des aiguilles d’une montre.
Français 䡬 Après avoir fait tourner le marteau rotatif à petite vitesse pendant un moment jusqu’à ce que la vis à bois soit partiellement enfoncée, pressez le trigger plus fortement afin d’obtenir la force d’entraînement maximale. PRECAUTION: 䡬 Ne manquez pas de prendre en considération la dureté du bois quand vous préparez un trou approprié à recevoir la vis à bois.
Français 8. Comment utiliser la mèche (queue conique) et le raccord de queue conique (1) Monter le raccord de queue conique sur le marteau rotatif à percussion. (Fig. 15) (2) Fixer la mèche (queue conique) sur le raccord de queue conique. (Fig. 15) (3) Mettre l’interrupteur sur la position de marche (ON) et percer un trou de la profondeur voulue.
Français (4) Engager la plaque de guidage dans la couronne et tourner la plaque de guidage à gauche ou à droite de manière à ce qu’elle à ce qu’elle ne puisse pas tomber, même si elle orientée vers le bas. (Fig. 19) 2. Perçage (Fig. 20) (1) Brancher la perceuse. (2) Un ressort est placé dans le goujon central. Appuyer légèrement l’outil perpendiculairement contre le mur ou le plancher. Toute la surface de la couronne doit être en contact avec le mur ou le plancher. Mettre en marche.
Français ENTRETIEN ET INSPECTION AVERTISSEMENT: S’assurer de mettre l’interrupteur d’alimentation sur la position OFF et de déconnecter la fiche de la prise secteur avant l’entretien et l’inspection de la meuleuse. 1. Contrôle du foret de perçage Etant donné que l’utilisation d’une mèche usée entraînera un mauvais fonctionnement du moteur et une diminution de l’efficacité, remplacez la mèche usée par une neuve ou aiguisez-la immédiatement et dès que vous notez une certaine usure. 2.
Español INFORMACIÓN IMPORTANTE Antes de utilizar o realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las instrucciones de operación, las precauciones de seguridad, y las advertencias de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES. 1. Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español eléctrica puede resultar en una lesión seria. (2) Vístase adecuadamente. No utilice ropa floja ni joyas. Si tiene pelo largo, recójaselo. Mantenga su pelo, ropa, y guantes alejados de las partes móviles. La ropa floja, las joyas, o el pelo largo pueden engancharse en las partes móviles. (3) Evite la puesta en marcha accidental. Cerciórese de que la alimentación de la herramienta eléctrica esté desconectada antes de enchufarla en una toma de la red.
Español 5. Servicio de reparación (1) El servicio de reparación deberá realizarlo solamente personal cualificado. El servicio de mantenimiento o de reparación realizado por personal no cualificado podría resultar en el riesgo de lesiones. (2) Para el servicio de mantenimiento o reparación de una herramienta, utilice solamente piezas de repuesto idénticas. Siga las instrucciones de la sección de mantenimiento de este manual.
Español La utilización e una herramienta eléctrica con una tensión superior a la nominal podría resultar en revoluciones anormalmente altas del motor, en el daño de la herramienta, y en la quemadura del motor. 16. No utilice nunca una herramienta defectuosa o que funcione anormalmente. Si la herramienta parece que funciona anormalmente, produciendo ruidos extraños, etc., deje inmediatamente de utilizarla y solicite su arreglo a un centro de reparaciones autorizado por Hitachi. 17.
Español AISLAMIENTO DOBLE PARA OFRECER UNA OPERACIÓN MÁS SEGURA Para garantizar una operación más segura de esta herramienta eléctrica, HITACHI ha adoptado un diseño de aislamiento doble. “Aislamiento doble” significa que se han utilizado dos sistemas de aislamiento físicamente separados para aislar los materiales eléctricamente conductores conectados a la fuente de alimentación del bastidor exterior manejado por el operador.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español MONTAJE Y OPERACIÓN APLICACIONES Acción combinada de rotación y golpeteo 䡬 Perforación de orificios de anclaje 䡬 Perforación de orificios de hormigón 䡬 Perforación de orificios de baldosa Rotación solamente 䡬 Perforación de orificios en hormigón o madera (con accesorios facultativos) 䡬 Apretar tornillos en metal o madera. (con accesorios facultativos) Función de percusión solamente 䡬 Cincelado leve de hormigón, ranuración, y retoque de bordes ANTES DE LA OPERACIÓN 1.
Español 6. Montaje de la broca (Fig. 2) (1) Para colocar una broca (SDS más vástago), tire completamente de la empuñadura en el sentido de la flecha como se muestra en la Fig. 2 en inserte profundamente la froca girándola. (2) Al soltar la empuñadura, la broca quadará asegurada. (3) Para extraer la broca, tire completamente de la empuñadura en el sentido de la flecha y tire hacia afuera de la broca. 7. Cuando instale la copa de polvo o el lector de polvo (B) (Accesorios facultativos)(Fig. 3, Fig.
Español 䡬 Cuando ponga en funcionamiento del martillo giratorio meintras el colector de polvo (B) esté separado de la superficie de hormigón, dicho colector girará junto con la broca. Cerciórese de apretar el gatillo interruptor después de haber presionado la copa de polvo sobre la superficie de hormigón. (Cuando emplee la copa de polvo con una broca de no más de 7-15/32" (190 mm) de longitud total, el colector de polvo (B) no podrá tocar la superficie de hormigón girará.
Español Palanquita selectora 2. Rotación + golpeteo Este martillo roto-percutor puede usarse en el modo de rotación y golpeteo presionando el pulsadory girando la palanca selectora hasta la . (Fig. 6) marca (1) Montar la broca (2) Presionar el interruptor de gatillo después de poner la punta de la broca en la posición para taladrar. (Fig. 7) (3) No es necesario presionar con fuerza la broca. Presionar ligeramente la broca de forma que el polvo producido al taladrar salga al exterior gradualmente.
Español PRECAUCIÓN: 䡬 La aplicación de fuerza excesiva acelerará el trabajo pero dañará la punta de la broca y reducirá la vida útil del martillo giratorio. 䡬 La broca puede salirse al quitar el martillo rotopercutor del orificio en el que se haya atascado. Para extraer esta herramienta es importante empujar hacia adelante, o gire la broca hacia la izquierda. 䡬 No intentar perforar orificios de anclaje o perforar el concreto con la máquina puesta en la función de rotación solamente.
Español colocar asi éste en los orificios. 䡬 Luego de hacer rotar la herramienta lentamente hasta que el tornillo quede parcialmente metido en la madera, apretar más el gatillo para obtener la fuerza óptima de atornillado. PRECAUCIÓN: 䡬 Tener cuidado al preparar el orificio para que sea apropiado para el tornillo, teniendo en cuenta la dureza de la madera. Si el orificio es excesivamente pequeño o estrecho, se requiere mucha fuerza para atornillar y a veces puede dañarse la rosca. Palanquita selectora 6.
Español 8. Modo de usar la broca (espiga ahusada) y el adaptador de la espiga ahusada (1) Montar el adaptador de la espiga ahusada en el martillo giratorio (Fig. 15). (2) Montar la broca (espiga ahusada) en el adaptador de la espiga ahusada (Fig. 15) (3) Poner el interruptor en la posición de encendido (ON), y taladrar un agujero de la profundidad especificada.
Español (4) Unir la placa guía con la barrena tubular y girar la placa guía hacia la izquierda o hacia la derecha de forma que no se caiga a pesar de estar indicando hacia abajo. (Fig. 19) 2. Modo de taladrar (Fig. 20) (1) Conectar el enchufe a la toma de alimentación. (2) El pasador central se ha instalado un resorte. Presionar ligeramente de forma perpendicular hacia la pared o hacia el pared o hacia el suelo.
Español MANTENIMIENTO E INSPECCIÓN ADVERTENCIA: Antes de realizar el mantenimiento o la inspección de la amoladora, cerciórese de desconectar la alimentación y de desenchufar el cable de alimentación del tomacorriente. 1. Inspeccionar la broca de taladro Debido a que el uso de brocs desafiladas pueden causar mal funcionamiento del motor y desmejorar la eficacia del taladro, hay que reemplazar las brocas en malas condiciones por nuevas o afilarlas de inmediato al advertir abrasión. 2.
Español ACCESORIOS ADVERTENCIA: Los accesorios para esta herramienta eléctrica se mencionan en este Manual de instrucciones. La utilización de otros accesorios puede resultar peligrosa y causar lesiones o daños mecánicos. NOTA: Los accesorios están sujetos a cambio sin ninguna obligación por parte de HITACHI. ACCESORIOS ESTÁNDAR (1)Caja (Plástica) (Molded plastic) (Núm. de código 307786) .................................... 1 (2)Mango lateral (Núm. de código 303659) .....................................
Español Diámetro externo Núm. de código 7/16" 944460 (11 mm) 31/64" 944461 (12,3 mm) 1/2" 993038 (12,7 mm) 9/16" 944462 (14,3 mm) 73/128" 944500 (14,5 mm) 11/16" 944463 (17,5 mm) 27/32" 944464 (21,5 mm) Modo cónico Núm. de código Cono Morse (No. 1) 303617 Cono Morse (No.
Español W 1/4" (6,3 mm) 10-15/64" (260 mm) 302976 Medida de ancla Longitud total Núm. de código W 5/16" (8 mm) 10-15/64" (260 mm) 302975 W 3/8" (9,5 mm) 6-19/64" (160 mm) 303621 10-15/64" (260 mm) 302974 W 1/4" (6,3 mm) 10-15/64" (260 mm) 302979 Medida de ancla Longitud total Núm.
Español Pasador central Núm. de código – – (A) 982684 (B) 982685 Barrena tubular (diámetro externo) 63/64"(25 mm) 1-9/64" (29 mm) (A) 1-1/4" (32 mm) 1-3/8" (35 mm) 1-1/2" (38 mm) 1-25/32" (45 mm) (B) 1-31/32" (50 mm) Núm. de código 982672 982673 982674 982675 982676 982677 982678 Espiga de la Núm. de código barrena tubular Overall length 4-1/8" 303625 (A) (105 mm) 11-13/18" 303626 (300 mm) 11-13/18" (B) 303627 (300 mm) Placa guia Barrent tubular Barrena tubular Núm. de código Núm.
Español 7. Trabajo de colocación de pernos para anclaje químico (rotación + golpeteo) Manguito adaptador a la venta el mercado (SDS más vástago) Adaptador de anclaje químico de 1/2" (12.7 mm) (Núm. de código303044) Adaptador de anclaje químico de 3/4" (19 mm) (Núm. de código 303045) 8. Perforación (rotación solamente) 䡬 Portabrocas, adaptador (G) del portabrocas, tornillo especál y llave de portabrocas Tornillo especial Núm. de código 981122 Porabrocas (13 VLR) (con llave de portabrocas) Núm.
Español 10. Colocación de tornillos (rotación solamente) No. de broca Adaptador (D) del portabrocas (SDS más vástago) Núm. de código 303624 Broca para tornillos Plillips No. de broca No.2 No.3 Tamaño del tornillo 1/8" ~ 3/16" (3 – 5 mm) 1/4" ~ 5/16" (6 – 8 mm) Longitud 31/32" (25 mm) 31/32" (25 mm) Núm. de código 971511Z 971512Z 11. Copa de polvo y colector de polvo (B) Copa de polvo Núm. de código 971787 Colector de polvo (B) Núm. de código 306885 12.
Español 69
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.