HITACHI COLOUR MONITOR CM650ET USER MANUAL MANUEL D’UTILISATION BEDIENUNGSANLEITUNG MANUAL DE USUARIO MANUALE DI ISTRUZIONI with EasyMenu ! E EasyMenu is HITACHI’s On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your colour monitor. . SERIAL No. The serial number is located on the rear of the monitor.
NOTE: The information in this manual is subject to change without notice. responsibility for any errors that may appear in this manual. The manufacturer assumes no TRADEMARK ACKNOWLEDGEMENT VGA is a registered trademark of International Business Machines Corporation. VESA is a trademark of a nonprofit organrsation, Video Electronics Standard Association EMRGY S.r.x@ is a trademark of Environmental Protection Agency (EPA).
Congratulations! You have just purchased a TC0’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE- 114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO’99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.
FEATURES ...................................................................................................... CAUTIONS ..................................................................................................... INSTALLATION .............................................................................................. STANDARD SETTINGS.. ............................................................................... OPERATION.. .....................................................................
n NEVER REMOVE THE REAR COVER ! __ The rear cover MUST be removed only by authorised service personnel. This colour - monitor contains high voltage components. .: n THE POWER POINT SHOULD BE CLOSE TO THE MONITOR AND EASILY ACCESSIBLE ! n INSTALL THE UNIT IN AN SUITABLE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment. DO NOT subject the unit to vibrations, dust, or corrosive gases.
n CAUTION for 200 - 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over-current protection. Refer to the following table for the suitable number and fl location of the protective devices which should be provided in the building installation. .
H FCC (Federal Communications Commission) STATEMENT WARNING -a _ .- WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
n FOR THE CUSTOMERS IN THE U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. ti - IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS E The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, m the value of which is indicated on the pin face of the plug.
Install the monitor in the following way, taking care to maintain safety REAR VIEW FRONT VIEW Rear Cover Signal Input Connector AC Inlet Control Panel Power Cord Tilt & Swivel Base v USB Slot / 7J-J - to a receptacle of (for the optional USB HUB Module) to the host computer - the correct voltage 1. Installation Install the monitor on a horizontal base. 2. Power Cord Connection @ Make sure of using the power cord meeting the safety standard of the country in which you are using the monitor.
Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been preprogrammed by the factory. No. Video Mode Name (with Resolution and Vertical Frequency) Horizontal Frequency Video Mode 640 x 400- 70 Hz 31.47 kHz VGA 2 VESA 640 X 400- 85 Hz 3 VESA 800 X 600- 85 Hz 37.86 kHz 53.67 kHz VESA 1 VGA VESA 4 VESA 1024 x 768- 75 Hz 60.02 kHz VESA 5 VESA 1024 X 768- 85 Hz 68.
Power LED Switches Switches Switch Power Switch POWER ON/OFF Press the Power switch, to switch the power ON or OFF. n When power is ON, the power LED lights. n After turning OFF the switch, wait at least 5 seconds before restarting the monitor. Otherwise the monitor may operate incorrectly. H If the picture doesn’t appear, turn OFF the power switch, make sure of the following and wait at least 30 seconds before restarting the monitor.
Table-l Function - + PINCUSHION PIN BALANCE recalls the factory preset modes. When the Green reaches When the Blue or Red the upper limit, it makes the reaches the upper limit, it Blue and Red weaker. make the Green weaker. B makes the Red and Green makes the Blue stronger. stronger. When the Blue reaches the When the Red or Green upper limit, it makes the reaches the upper limit, it Red and Green weaker. make the Blue weaker.
Table-l (continued) Function B H.MOIRE @nJ V.MOIRE LANGUAGE a SELECT POWER m MANAGEMENT SJEJ -9 Rig AUTO SAVE DEGAUSS EXIT - + makes the operation of makes the operation of horizontal moire circuit horizontal moire circuit weaker. stronger. makes the operation of makes the operation oi vertical moire circuit weaker. vertical moire circuit stronger. c h a n g e s t h e EasyMenu c h a n g e s t h e EasyMenu language to the previous language to the next mode. mode.
When the monitor has detected the change of the signal input condition, the monitor will indicate the condition automatically, as follows. the horizontal frequency Precision frequency, Horizontal *2kHz mode. Refer to MANAGEMENT SYSTEM” below. This monitor meets the EDGY STAR@, VESA DPMS (Display Power Management Signalling) The monitor has a built-in power management system that standard specifications. automatically reduces power consumption when the PC is not in use.
= CRT I- 17 inch picture tube, 0.22 mm horizontal dot pitch (0.21 mm horizontal mask pitch) 100’ deflection, FS double focus, AR-ASC coating. : 0.7 Vp-p, analogue : Separate H/V, TTL level Composite H/V, TTL level input Signal Video Sync. Synchronisation Horizontal : 31 - 69 kHz : 50-130Hz Vertical Resolution Horizontal : 1280 dots (max.) Vertical : 1024 lines (max.) Video Clock frequency 110 MHz (typical) Viewable Image Size 16.