PROJECTION COLOR TV 65SWX20B 57SWX20B 51SWX20B 65TWX20B 57TWX20B OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS FIRST TIME USE 2-3 4-20 THE REMOTE CONTROL 21-37 ON-SCREEN DISPLAY 38-62 USEFUL INFORMATION INDEX 63-68 Video Audio Ch. Manager Locks Setup Move SEL Sel As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
IMPORTANT SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.
IMPORTANT Read before operating equipment 15. Televisions are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury. 16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. 17.
ACCESSORIES Check to make sure you have the following accessories before disposing of the packing material. SIMPLE REMOTE CONTROL REMOTE CONTROL IR MOUSE CABLE BATTERIES (“AA”) POWER VCR TV CBL STB SOURCE WIZARD CD TAPE DVD A/V NET AMP 1 2 3 4 5 6 7 8 9 CH + VOL + VOL SELECT 0 SLEEP INFO ASPECT A/V NET C.C. FAV CH MUTE ANT VIRT UAL HD CH MENU ANT ME EXIT EX NU 3.
HOW TO SET UP YOUR NEW HITACHI PROJECTION TV ANTENNA Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen.
HOOK-UP CABLES AND CONNECTORS Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.
FRONT PANEL CONTROLS PULL POWER S-VIDEO -AUDIOVIDEO L/MONO R MAGIC FOCUS VOL- VOL+ CH- CH+ INPUT MENU EXIT SELECT INPUT 5 MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode. INPUT/EXIT button Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source.
FRONT PANEL JACKS AND CONNECTORS The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: S-VIDEO -AUDIOVIDEO L/MONO R S-VIDEO MAGIC FOCUS INPUT 5 NOTE: -AUDIOVIDEO L/MONO R MAGIC FOCUS INPUT 5 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3.
REAR PANEL JACKS ANT A DVI-HDTV PR PB R (MONO)/L Y INPUT 1 TO CONVERTER ANT B AUDIO INPUT 2 PR PB R (MONO)/L Y/VIDEO AUDIO R (MONO)/L VIDEO S-VIDEO R (MONO)/L VIDEO S-VIDEO INPUT 3 AUDIO TO HI-FI CENTER IN INPUT 4 IR BLASTER L R L VIDEO S-VIDEO MONITOR OUT AUDIO R Antenna Input/Output The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture.
REAR PANEL JACKS Component: Y-PBPR Inputs Inputs 1 and 2 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use standard video signal for INPUT:2. NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority over VIDEO input. 2. Your component outputs may be labeled Y, B-Y, and R-Y.
REAR PANEL CONNECTIONS TYPICAL FULL-FEATURE SETUP CONNECT TO IR BLASTER (Provided) Infrared Receiver DIGITAL OUTPUT CAPABILITY Outside antenna or cable TV coaxial cable DIGITAL OUTPUT DVD Player 2-Way signal splitter Y OUTPUT PB/CB PR/CR L HDTV Set-Top Box R Y PB PR OUTPUT L R VCR #1 ANT A ANT IN DVI-HDTV PR PB R (MONO)/L OUTPUT S-VIDEO V L R Y INPUT 1 TO CONVERTER AUDIO INPUT 2 ANT B PR PB R (MONO)/L Y/VIDEO AUDIO R (MONO)/L VIDEO S-VIDEO R (MONO)/L VIDEO S-VIDEO IN
TIPS ON REAR PANEL CONNECTIONS S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. If your device has only one audio output (mono sound), connect it to the left audio jack on the television. Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
CONNECTION EXTERNAL AUDIO SOURCES To control the audio level of an external audio amplifier with the remote control, connect the system as shown below.
CONNECTING EXTERNAL VIDEO SOURCES The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs. The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A STEREO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4. Press the VID2~VID5 button to view the program from the VCR or laserdisc player.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below. 2. Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3. Connect the cable from the CR/PR OUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. 4.
CONNECTING A/V NETWORK Your Hitachi Television is equiped with an A/V Network feature. This feature helps to control your external Audio/Video equipment (VCR, Set Top Box, DVD, etc.). Once this is setup, it allows your IR Mouse connector to control your equipment using your Hitachi TV Remote Control. You can use your Hitachi remote control to control the Audio/Video equipment command without the equipment’s remote control. The Television rear panel has 2 IR BLASTER jacks.
A/V NETWORK SETUP WIZARD 4. 5. Press the A/V NET button on the remote control. The A/V Network Setup Wizard will automatically start upon the very first use. You can access the Setup Menu Wizard again in the future by pressing the A/V net button and selecting SETUP. Follow the steps below to setup your A/V network (See page 20 for A/V Network Codes). There are six steps in this procedure.
AUDIO/VIDEO NETWORK (A/V NET) CODES VCR BRAND . . . . . . . . . . . . . . . . . . . . . . . CODE Admiral . . . . . . . . . . . . . . . . . . . . . . . . 0048, 0209 Adventura . . . . . . . . . . . . . . . . . . . . . . . . . . .0000 Aiko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 Aiwa . . . . . . . . . . . . . . . . . . . . . 0307, 0000, 0037 Akai . . . . . . . . . . . . . . . . . 0106, 0053, 0041, 0061 America Action . . . . . . . . . . . . . . . . . . . . . . . 0278 American High .
THE REMOTE CONTROL In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-box, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area. To operate your TV, point the remote control at the remote sensor of the TV and press the TV button.
HOW TO USE THE REMOTE TO CONTROL YOUR TV POWER VCR TV CBL STB SOURCE WIZARD CD TAPE DVD AMP 1 2 3 4 5 6 7 8 9 0 SLEEP ANT INFO ASPECT A/V NET C.C.
HOW TO USE THE REMOTE TO CONTROL YOUR TV CD, TAPE, AMP buttons When pressed, each of these buttons will blink to indicate the remote is in Audio mode. (see page 35) CHANNEL selector buttons CHANNEL selector buttons are used to select channels, lock access code, etc. Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune.
HOW TO USE THE REMOTE TO CONTROL YOUR TV AV/NET button Press this button to access the Audio/Video network (A/V Net) menu. The A/V Net allows the user to control external components with the TV’s remote control. When you press the A/V NET button, the following window will pop up within the Display screen. The window will disappear after eight seconds if you don’t press any buttons. Press the A/V NET button again and the last window displayed will appear.
HOW TO USE THE REMOTE TO CONTROL YOUR TV ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal, the picture format ratio allows you to adjust the images through the following options. 4:3 STANDARD Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source.
HOW TO USE THE REMOTE TO CONTROL YOUR TV NOTES: 1. 2. Depending on the input signal, some of the aspect features will not be available. Set up a Component signal (connect component to Y-PBPR inputs) and switch to VIDEO:1 or 2 by pressing the VID1 or VID2 button on the Remote Control when planning to use all picture formats features. VIRTUAL HD button Press this button to toggel between 1080i and 540p. MENU button The MENU button will start the On-Screen Display.
HOW TO USE THE REMOTE TO CONTROL YOUR TV 1 PICTURE-IN-PICTURE buttons See separate section on pages 28~30 for a description. PIP CH button Use the PIP CH button to select between main picture and sub-picture tuning. The channel number which is highlighted indicates what channel is being controlled. 23 VID1 ~ VID5 When the remote control is in TV mode, press these buttons to directly select the video input sources between the five video inputs.
PICTURE-IN-PICTURE (PIP) Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B). ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.
PICTURE-IN-PICTURE (PIP) SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub-picture evenly on the screen. Ant A 10 Ant A 12 Sub Picture Main Picture SURF MODE PICTURE-IN-PICTURE This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures, Press the PIP button a second time to remove the sub-pictures from the screen. Ant A 28 PIP PIP Ant A 7 NOTES: 1. 2. 3. 4. 5.
PICTURE-IN-PICTURE (PIP) FREEZE button (With PIP ON) If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again. NOTE: When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen.
USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR. (refer to page 37 for pre-codes) 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. Press and release the VCR button to switch to VCR pre-coded mode. 4.
USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box. (refer to page 37) 1. Turn ON your cable box. 2. Aim the remote control at the front of your cable box. 3. Press and release the Cable (CBL) button to switch to Cable pre-coded mode. 4.
USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems. (refer to page 37) 1. Turn ON your set-top-box/satellite systems. 2. Aim the remote control at the front of your set-top-box/satellite systems. 3.
USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player. (refer to page 37 for pre-codes) 1. Turn ON your DVD player. 2. Aim the remote control at the front of your DVD player. 3. Press and release the DVD button to switch to DVD pre-coded mode. 4.
USING YOUR REMOTE TO CONTROL ADDITIONAL AUDIO EQUIPMENT Operating the precoded function for your Audio component. This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component. (refer to page 37 for pre-codes) 1. Turn ON your Audio component you wish to control with the Remote. 2. Aim the remote control at the front of your Audio component. 3.
THE SIMPLE REMOTE CONTROL HITACHI has provided a second remote control for your convenience. The Simple Remote Control has the basic features that are most often used. A/V NET CH + FAV CH CH - SELECT MUTE VOL + VOL - MENU ANT EXIT POWER POWER button Press Power button to turn the TV set ON or OFF. CH+ ( ), CH- ( ) Press the CH+ ( ) up or CH- ( ) down buttons to select desired channel or to navigate the on screen display features when in A/V NET mode.
VCR, CABLE, SATELLLITE, DVD and AUDIO/VIDEO CODES FOR REMOTE CONTROL VCR BRAND. . . . . . . . . . . . . . . . . CODE Adventura . . . . . . . . . . . . . . . . . . . . . . 01 Aiko. . . . . . . . . . . . . . . . . . . . . . . . . . . 09 Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 01 Akai . . . . . . . . . . . . . . . . . . . . . 02, 47, 48 American High. . . . . . . . . . . . . . . . . . . 23 Asha . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Audiovox . . . . . . . . . . . . . . . . . .
OSD 1. Press MENU on the remote control to display the different features on your HITACHI Projection TV. 2. Press the THUMB STICK to highlight a different feature. 3. Press EXIT on the remote control to quickly exit from a menu. A/V Net 4. Press A/V Net on the remote control to access the A/V Net menu to control external components. 5. Press THUMB STICK or to access Favorite Channels menu. ME NU EX IT SELECT This part of the screen shows which selections are available. Video Audio Ch.
OSD Picture Mode Video Advanced Settings Select between the four picture modes: Sports, Movies, News, and Music. Adjust contrast. Adjust brightness. Adjust color. Adjust tint. Adjust sharpness. Centering top and bottom of the picture. Automatic or manual alignment of the Red, Green and Blue colors to make white. Automatically change tint and color coordinates for DTV program. Improve picture performance. Treble Bass Balance Sound Enhancement Advanced Settings Adjust the treble. Adjust the bass.
VIDEO Video Select VIDEO to adjust picture settings and improve picture quality. Picture Mode Use this function to choose from automatic picture settings to optimize your TV’s performance. Video Audio Ch.
VIDEO Use the THUMB STICK or to highlight the function to be adjusted. Press the THUMB STICK or to adjust the function. Press down on THUMB STICK to select the function settings. Press MENU to return to main menu or select PICTURE MODE to return to previous menu. Press EXIT to quit menu. Contrast Brightness Use this function to change the contrast between black and white levels in the picture. This adjustment will only affect the picture when ADVANCED SETTINGS DIMMER is OFF.
VIDEO Magic Focus Auto Digital Convergence Adjustment Please turn ON your television for at least 20 minutes before using this feature. Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely aligned over each other so that the colors can be mixed.
VIDEO Manual Convergence Adjustment Mode NOTES: 1. 2. Please turn ON your television for at least 20 minutes before using this feature. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode. DO NOT press MAGIC FOCUS or use Auto Adjustment Mode after using Manual Adjustment Mode. Using the Remote Control, select VIDEO-MAGIC FOCUS-MANUAL ADJUSTMENT MODE to access convergence crosshatch pattern.
VIDEO Color System This function allows you to automatically change tint and color coordinates for DTV programs. HDTV - High Definition Television - Use for High Vision Signal Y-PBPR from HDTV Set-Top Box. SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-CBCR. NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be abnormal. 2.
AUDIO Audio Select AUDIO to adjust the TV to your preference and to improve the sound quality. Audio Video THUMB STICK Audio Treble 50% Ch.
AUDIO Sound Enhancement The following surround settings will reproduce the “live” sound you would hear in concert halls, sports stadiums, movie theaters, etc. with only two speakers. Audio Audio Treble 50% Bass 50% Balance Sound Enhancement Sound Enhancement THUMB STICK SRS BBE BBE Mach3Bass Advanced Settings SELECT Move SEL Select Move SEL Return To enter SOUND ENHANCEMENT, use THUMB STICK or to highlight then press down on THUMB STICK to select SOUND ENHANCEMENT of your choice.
AUDIO Advanced Settings Use ADVANCED SETTINGS to improve the sound performance of your TV, depending on listening conditions. Audio Audio Treble 50% Bass 50% L Balance Advanced Settings R Sound Enhancement THUMB STICK Advanced Settings Audio Source Stereo Mono Internal Speakers ON TV as Center 2nd Audio Prog. OFF SELECT Move SEL Select Auto Noise Cancel Perfect Volume Loudness Move SEL Return Press THUMB STICK or to highlight a function.
CHANNEL MANAGER Channel Manager This function allows you to review which channels are labeled (CH ID), which have been added to Channel Memory (SCAN), and which are protected by LOCK. Ch. Manager Ch. Manager Ant A Ant A Ant B Move SEL Select THUMB STICK SELECT Ch# Scan Ch ID 2 Off -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Move SEL Lock Return Press THUMB STICK or to review more channels.
CHANNEL MANAGER This selection contains advanced features which will make TV viewing easier and more enjoyable. Use this feature to give up to 20 channels a name when ANTENNA signal source is selected and up to 60 channels a name when CATV signal source is selected.
LOCKS This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. Locks The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000. Use the number buttons to select access code. Video Audio Ch.
LOCKS Movie Ratings Use MOVIE RATINGS to eliminate from viewing, any movie that you feel may be inappropriate due to its content. Locks THUMB STICK ME Locks Change Access Code Movie Ratings Engage Lock Status Not Rated: TV Time Lock THUMB STICK Movie Ratings G: PG: TV Ratings NU SELECT Canadian Ratings (Eng) PG-13: Canadian Ratings (Frn) Move SEL R: Select NC-17: X: Move SEL Return Use THUMB STICK or to select the MOVIE RATING category that you want to block.
LOCKS TV Ratings Use TV RATINGS to eliminate from viewing any TV program that you feel may be inappropriate due to its content. Locks Locks TV Ratings Change Access Code Status Engage Lock THUMB STICK ME TV Time Lock THUMB STICK Movie Ratings TV Ratings NU Sub Rating D L S V FV TV-Y: TV-Y7: SELECT Canadian Ratings (Eng) TV-YG: Canadian Ratings (Frn) TV-PG: Move SEL Select TV-14: TV-MA: Move SEL Return Use THUMB STICK or to highlight the category that you want to block.
LOCKS Canadian Ratings (Eng) Use Canadian Ratings (Eng) to block various types of movies and television programs used in Canada that you feel may be inappropriate due to its content.
LOCKS Canadian Ratings (Frn) Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel may be inappropriate due to its content.
SETUP Setup Select SETUP when setting your TV up for the first time. Use the THUMB STICK or on the remote to highlight the function desired. Setup Video Menu Preference Audio Set The Clock Ch. Manager THUMB STICK ME THUMB STICK Locks Setup Set The Channels Set The Inputs Set Event Timer NU Move SEL Sel SELECT Set Closed Captions About Your TV Move SEL Select Use THUMB STICK or to select the sub-menu of your choice.
SETUP Set The Menu Background This function allows you to choose from two menu backgrounds. Setup Menu Preferences Set The Language English Francais THUMB STICK Español Set The Menu Background Shaded Solid Move SEL Select Use THUMB STICK , to highlight SET THE MENU BACKGROUND (shaded or solid), and press down on THUMB STICK to select setting. Press EXIT to quit menu or THUMB STICK to return to previous menu.
SETUP Set The Channels Select ANTENNA if you are using an indoor or outdoor antenna. Select Cable if you have cable TV.
SETUP This feature will automatically store active TV channels in Auto Channel Scan. This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ).
SETUP Set The Inputs Use this feature to give a name to any of the five video inputs.
SETUP Video 2 Auto Link Use this function to automatically turn the TV on and tune to Video2 when it detects a video signal to input 2.
SETUP This function will automatically turn the Projection TV on and off, one time only, every day, or once a week. Set Event Timer If the clock is not set (see page 56), you can not use this function and the screen below will appear. Please Set The Clock First.
SETUP Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or .
CARE OF YOUR HITACHI TELEVISION AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Place your Television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances, when you go on vacation.
Reception Problems • IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception.
TV i ure No Picture, no sound Try SYMPTOMS ss rd cor is p rec lug t ge wit d in an c he oth d ''O er N" cha Ch nn eck el ( an sta ten t ion na Ch tr o eck con ub ne an le) ctio ten ns na Ch (ba for eck ck bro ou of T ken tsid V) Ch lea ea eck d-i nte n nn for wir a loc e al i Ad nte jus tC r fe ren on t r ce a Ad st c jus on tB tr o rig l htn Ad ess jus con tC tr o olo l rc Ad on jus tr o tT l int con Ad tr o jus l tV olu me con tr o l CH TR E C K Y T TH HE E S Be SE E I sur AD T E M ee xte J
USEFUL INFO Features: • • • • • • • • • • • • • • • • • • • Superfine Picture Quality 1280 Line Horizontal Resolution Remote (Controls many VCR brands, cable boxes, satellite boxes, and other audio equipment.) Extra Simple Remote for easy basic operations. High Definition On-Screen Display New A/V Network System Control Control up to 4 components with one remote. (2 IR Mouse cables included.
USEFUL INFO e c i v r se To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day 800 HITACHI (1-800-448-2244) Hitachi America, LTD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
USEFUL INFO Hitachi Canada, LTD. Digital Media Division Should you have any questions regarding warranty, service, operation, or technical assistance, please contact: In Canada: 1-800-HITACHI (1-800-448-2244) Monday - Friday EST 9:00am - 7:00pm Saturday EST 9:00am - 5:00pm Look for your French Manual on the outside of the box. If the manual is missing, call 1-800-HITACHI (1-800-448-2244) for a copy.
NOTES 69
NOTES 70
NOTES 71
QR51881