PROJECTION COLOR TV 53FDX20B 53SDX20B 53SDX20BB 43FDX20B 43FDX15B OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS FIRST TIME USE SETUP SEL CUSTOMIZE VIDEO AUDIO THEATER 2-3 4-18 REMOTE CONTROL 19-29 ULTRATEC BIT-MAP ON-SCREEN DISPLAY 30-60 USEFUL INFORMATION INDEX 61-66 As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 15. Televisions are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury. 16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. 17.
ACCESSORIES Check to make sure you have the following accessories before disposing of the packing material. PART NAME CLU-4322UG REMOTE CONTROL PART NO. ILLUSTRATION POWER HL01832 TV CBL/SAT DVD/VCR SWAP PIP MODE PIP PIP CH HELP FREEZE MENU SELECT MUTE LAST CH EXIT VOL CH 1 2 3 4 5 6 7 8 9 ANT 0 STATUS VID1 VID2 REC VID3 VID4 ASPECT MODE VID5 CLU-4322UG 1. 43” TELEVISION STAND SP-43H (Not included, order separately) OPTIONAL 2.
HOW TO SET UP YOUR NEW HITACHI PROJECTION TV ANTENNA Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen.
HOOK-UP CABLES AND CONNECTORS Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.
FRONT PANEL CONTROLS FRONT VIEW PUSH CH+ POWER INPUT MENU VOL- VOL+ SRS ( G )/ EXIT SELECT 쏐 CH- Push open door and pull forward and down CH+ POWER INPUT MENU VOL- VOL+ MAGIC FOCUS EXIT SELECT CH- MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.
FRONT PANEL CONTROLS POWER light You will see a red light when the TV is turned on. PERFECT PICTURE sensor The Perfect Picture sensor will make automatic picture adjustments depending on the amount of light in the room to give the best picture. (see page 57) REMOTE CONTROL sensor Point your remote at this area when selecting channels, adjusting volume, etc. MAGIC FOCUS Use this button to adjust your picture quality to optimum performance.
FRONT PANEL JACKS AND CONNECTIONS The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: MAGIC FOCUS S-VIDEO VIDEO L/MONO INPUT 3 R AUDIO INPUT S-INPUT (Optional, see note) OUTPUT S-VHS V L R OUTPUT Back of VCR NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal. 2.
REAR PANEL JACKS ANT A TO CONVERTER ANT B S-VIDEO S-VIDEO VIDEO VIDEO Y/VIDEO (MONO) (MONO) S-VIDEO L L R R PB (MONO) L PR AUDIO TO HI-FI AUDIO R PB (MONO) L L R R PR R AUDIO AUDIO VIDEO Y/VIDEO AUDIO AUDIO L INPUT 1 INPUT 2 INPUT 4 INPUT 5 MONITOR OUT Antenna Input/Output The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture.
REAR PANEL JACKS Component: Y-PBPR Inputs Inputs 4 and 5 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use standard video signal for INPUT:4 and 5. NOTES: 1. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s PR input. 2. Your component outputs may be labeled Y-CBCR.
REAR PANEL CONNECTIONS TYPICAL FULL-FEATURE SETUP Outside antenna or cable TV coaxial cable 2-Way signal splitter DVD Player VCR #1 ANT IN OUTPUT S-VIDEO V L OUTPUT PB/CB PR/CR L Y R R Optional, see tips on page 13 VCR #2 S-VIDEO ANT A Optional, see tips on page 13 TO CONVERTER ANT B S-VIDEO S-VIDEO VIDEO VIDEO Y/VIDEO (MONO) (MONO) S-VIDEO L L PB (MONO) L PR L R INPUT R AUDIO TO HI-FI AUDIO R L L R R AUDIO AUDIO R AUDIO L INPUT 1 Stereo System Amplifier PB (MONO) PR
TIPS ON REAR PANEL CONNECTIONS TIPS ON REAR PANEL CONNECTIONS S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. If your device has only one audio output (mono sound), connect it to the left audio jack on the television. Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
CONNECTING EXTERNAL AUDIO SOURCES CONNECTING EXTERNAL AUDIO AMPLIFIER To control the audio level of an external audio amplifier with the remote control, connect the system as shown below.
CONNECTING EXTERNAL VIDEO SOURCES The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs. The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A STEREO SOURCE TO INPUT1~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4. Press the VID1~VID5 button to view the program from the VCR or laserdisc player.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING AN S-VIDEO SOURCE TO INPUT 1, 2 AND 3 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A COMPONENT SOURCE TO VIDEO 4 OR 5: Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below. 2. Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3. Connect the cable from the CR/PR OUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. 4.
THE REMOTE CONTROL In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CBL (Cable TV) converters, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area. To operate your TV, point the remote control at the remote sensor of the TV and press the TV button. The remote will now control your television.
HOW TO USE THE REMOTE TO CONTROL YOUR TV TV POWER button POWER TV PICTURE-IN-PICTURE CBL/SAT DVD/VCR SWAP PIP MODE PIP PIP CH HELP FREEZE MENU HELP button MENU button PIP CH button SELECT SELECT, MENU, CURSOR buttons MUTE LAST CHANNEL (LAST CH) button LAST CH EXIT EXIT button VOLUME, MUTE buttons VOL CHANNEL SELECTOR buttons ANT button CH 1 2 3 4 5 6 7 8 9 ANT 0 STATUS VID1 VID3 VID4 ASPECT MODE VID2 REC STATUS button VID5 VID1~VID5 buttons MO
HOW TO USE THE REMOTE TO CONTROL YOUR TV CHANNEL SELECTOR buttons Use these buttons to select the CHANNEL you wish to watch. ANTENNA button The ANT button will select between Antenna A and Antenna B each time the button is pressed. Ant A 10 Ant B 28 ANT VID1 ~ VID5 buttons When the remote control is in TV mode, press these buttons to directly select the video input sources between the five video inputs.
HOW TO USE THE REMOTE TO CONTROL YOUR TV LAST CHANNEL (LAST CH) button Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.) Ant A 39 Ant A 10 LAST CH PIP CH button Use the PIP CH button to select between main picture and sub-picture tuning. The channel number which is highlighted indicates which channel is being controlled. MENU button The MENU button will start the On-Screen Display.
PICTURE-IN-PICTURE (PIP) Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B). ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.
PICTURE-IN-PICTURE (PIP) PICTURE-IN-PICTURE CONT. SURF MODE PIP This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures, along the right edge of the screen. Press the PIP button a second time to remove the sub-pictures from the screen. Ant A 28 09 PIP 10 PIP 12 NOTES: 1. 2. 3. 4. 5, If no buttons are pressed when in SURF mode, auto-scanning will continuously scan channels in memory.
PICTURE-IN-PICTURE (PIP) FREEZE button (With PIP ON) If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again. NOTE: The FREEZE function will only operate when SINGLE PIP mode is chosen.
USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR. (refer to page 29 for pre-codes) 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. Press and release the DVD/VCR button to switch to VCR pre-coded mode. 4.
USING THE REMOTE TO CONTROL CABLE/SATELLITE BOX FUNCTIONS Operating the precoded function for your cable/satellite box. This remote is designed to operate different types of cable/satellite boxes. You must first program the remote to match the remote system of your cable/satellite box. (refer to page 29) 1. Turn ON your cable/satellite box. 2. Aim the remote control at the front of your cable/satellite box. 3.
USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player. (refer to page 29 for pre-codes) 1. Turn ON your DVD player. 2. Aim the remote control at the front of your DVD player. 3. Press and release the DVD/VCR button to switch to DVD pre-coded mode. 4.
CABLE, SATELLITE, VCR, AND DVD CODES CABLE BRAND CODE SATELLITE BRAND CODE VCR BRAND CODE DVD BRAND CODE General Instrument . . . . . . . . . . . . . . . . . . . . . . . . .17 Hamlin . . . . . . . . . . . . . . . . . . . . . . . . . . .22,23,24,25 Jerrold . . . . . . . . . . . . . . .00,01,02,03,04,05,06,07,21 Oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26,27,28 Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . .18,19,20 Pioneer . . . . . . . . . . . . . . . . . . .
SETUP CUSTOMIZE VIDEO AUDIO THEATER SEL ULTRATEC OSD 1. Press MENU on the remote control to display the different features on your HITACHI Projection TV. 2. Press CURSOR , , , to highlight a different feature. 3. Press EXIT on the remote control to quickly exit from a menu. 4. Press HELP on the remote control when a menu is displayed, and text will appear giving a description of that menu. MENU HELP SELECT EXIT This part of the screen shows what selections are available.
SETUP CUSTOMIZE VIDEO AUDIO THEATER SEL ULTRATEC OSD SETUP CUSTOMIZE VIDEO AUDIO THEATER Set Menu Language Plug & Play Set Antenna/Cable Set Channel Memory Edit Channel Memory View Channel List Set The Clock Magic Focus Picture Formats Choose English, French, or Spanish text. Optimum hook up for your system. Select Antenna or Cable TV. First time set up for channel buttons. Channel buttons, add or skip. Check channel name, scan, and child lock. Set before using timer features.
SETUP SET UP Select SETUP when setting your TV up for the first time. Use the CURSOR or on the remote to highlight the function desired. SETUP SETUP CUSTOMIZE VIDEO AUDIO THEATER SEL Se t M e n u Language Plu g & Play Se t An te nna/C abl e Se t Ch a nnel Memory Ed it Ch a nnel Memory Vie w Ch annel Li st Se t T h e C l ock M a g ic F ocus Pictu r e Formats MENU To Q u i t Exit Use CURSOR or to select the sub-menu of your choice.
SETUP SET UP This graphic guide function will help you to properly set up your TV or Home Theater System. Simply answer three questions and a graphic will be displayed, showing you the optimum setup for your personalized system.
SETUP SET UP SET ANTENNA/CABLE SETUP Select ANTENNA if you are using an indoor or outdoor antenna. Select CATV if you have cable TV.
SETUP SET UP SET CHANNEL MEMORY This feature will automatically store active TV channels in SET CHANNEL MEMORY. This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ).
SETUP SET UP EDIT CHANNEL MEMORY SETUP CUSTOMIZE Use this function after SET CHANNEL MEMORY is completed to add or erase additional channels to the remote control CHANNEL or buttons.
SETUP SET UP VIEW CHANNEL LIST This function allows you to review which channels are labeled in NAME THE CHANNEL, which have been added to EDIT CHANNEL MEMORY (SCAN), and which are protected by SET PARENTAL LOCKS.
SETUP SET UP SET THE CLOCK The time must be set before you can SET PROGRAM TIMER or TV TIME OUT.
SETUP SET UP MAGIC FOCUS Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called “convergence”.
SETUP SET UP The PICTURE FORMATS function is very useful when setting up reception High Definition, Standard Definition and NTSC signals.
SETUP SET UP Picture Formats Depending on the input signal, the PICTURE FORMAT aspect ration allows you to adjust the image through the following options. (1) NTSC Input - ANT A/B, VID1 ~ VID5, - 4x3 Format SETUP Input Aspect 1 (4x3 mode) 4x3 NTSC Aspect 1 540p/1080i Normal Aspect key Aspect 3 (Zoom 1 Mode) Aspect 3 540p/1080i Input Letter 16x9 NTSC Normal Aspect key Press Select To Set Picture Formats Aspect Style V.
SETUP SET UP (3) 480p Input - Input 4/5 (Component) - 4x3 Format SETUP SEL Aspect 1 (4x3 mode) Normal Aspect key Aspect 1 540p/1080i Aspect 2 405p/810i Press Select To Set Picture Formats Aspect Style V. Position Comp Color Type Video Display Input 4x3 480p Aspect 2 (16x9 mode) Aspect key Aspect key Aspect 4 (Zoom 2 mode) Menu Aspect key Aspect key Aspect 4 540p/1080i Aspect 3 (Zoom 1 Mode) Aspect 3 540p/1080i To M e n u B a r SETUP SEL V.
CUSTOMIZE CUSTOMIZE This selection contains advanced features which will make TV viewing easier and more enjoyable. CUSTOMIZE NAME THE CHANNEL Use this feature to give up to 20 channels a name when ANTENNA signal source is selected and up to 60 channels a name when CATV signal source is selected. SETUP CUSTOMIZE VIDEO THEATER AUDIO CUSTOMIZE SEL CURSOR MENU SEL Na me t h e Ch a n n e ls Na m e th e In p u ts Se t F a vo r ite Ch .
CUSTOMIZE CUSTOMIZE NAME THE INPUTS SETUP Use this feature to give a name to any of the five video inputs. CUSTOMIZE VIDEO AUDIO THEATER CUSTOMIZE SEL SEL Name the Channels N a m e t h e I np u t s S e t F a v o r i t e Ch .
CUSTOMIZE CUSTOMIZE This function allows you to group your favorite channels into six personalized categories that you can rename. A total of 36 channels can be stored in the FAVORITE CHANNELS function. SET FAVORITE CHANNELS SETUP VIDEO CUSTOMIZE THEATER AUDIO SETUP SEL VIDEO CUSTOMIZE AUDIO THEATER SEL Name the Channels N a m e t he In p u ts S e t F a v o rit e Ch .
CUSTOMIZE CUSTOMIZE FAVORITE CHANNELS (OPERATION) Use this function to display FAVORITE CHANNEL selections as sub-pictures or to tune the main picture to a desired favorite channel. Se t F a v o rit e Ch . C H 12 3 CH 3 CURSOR M OVIES 3 6 8 MOV IES 3 6 8 MENU 11 12 13 11 12 13 Menu 6 To S u r f To Q u i t Menu Exit To S u r f 8 To Q u i t Exit CURSOR CH 11 M OVIES 3 6 8 12 11 12 13 Menu To S u r f 11 13 To Q u i t Exit Select a category using CURSOR or .
CUSTOMIZE CUSTOMIZE SET PARENTAL LOCKS This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled amount of time that you set. The code to enter SET PARENTAL LOCKS is a four digit secret code number. The factory preset code is 0000. Use the number buttons to select secret code.
CUSTOMIZE CUSTOMIZE MOVIE RATINGS Use MOVIE RATINGS to eliminate from viewing, any movie that you feel may be inappropriate due to its content.
CUSTOMIZE CUSTOMIZE TV RATINGS Use TV RATINGS to eliminate from viewing any TV program that you feel may be inappropriate due to its content.
CUSTOMIZE CUSTOMIZE CANADIAN RATINGS (ENG) Use CANADIAN RATINGS (ENG) to block various types of movies and television programs used in Canada that you feel may be inappropriate due to its content.
CUSTOMIZE CUSTOMIZE CANADIAN RATINGS (FRN) Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel may be inappropriate due to its content.
CUSTOMIZE CUSTOMIZE This function will automatically turn the TV on and off, one time only, every day, or once a week. SET PROGRAM TIMER SETUP CUSTOMIZE VIDEO AUDIO THEATER SEL Name the Channels Nam e t h e I n p u ts Set F a vo ri t e Ch .
CUSTOMIZE CUSTOMIZE VIDEO INPUT SENSOR SETUP Use this function to automatically turn the TV on and tune to VIDEO: 4 when it detects a VIDEO input. CUSTOMIZE VIDEO AUDIO CUSTOMIZE THEATER SEL SEL N a m e T h e Ch a n n e ls N a m e T h e In p u ts S e t F avo r ite Ch .
CUSTOMIZE CUSTOMIZE Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or . CLOSED CAPTION SETUP CUSTOMIZE VIDEO AUDIO THEATER CUSTOMIZE SEL SEL C losed C aption N a m e th e Ch a n n e ls N a m e th e In p u ts S e t F a vo r ite Ch .
VIDEO VIDEO Select VIDEO to adjust picture settings and improve picture quality. VIDEO SETUP CUSTOMIZE VIDEO AUDIO THEATER SEL CURSOR MENU Co n tra s t Brig h tn e s s Co lo r Tin t Sh a rp n e s s Re s e t Ad v a n c e d Se ttin g s Menu To Menu Bar 100% 50% 50% CURSOR 50% Con t rast To Quit Menu Exit To Menu Bar 100% To Quit Exit Use the CURSOR or to highlight the function to be adjusted. Press the CURSOR or to adjust the function. Press EXIT to quit menu.
VIDEO VIDEO Your HITACHI Projection TV has a PERFECT PICTURE function which will automatically adjust picture settings to produce the highest quality picture possible. When PERFECT PICTURE is highlighted, press the SELECT button to turn the PERFECT PICTURE on or off.
AUDIO AUDIO Select AUDIO to adjust the TV to your preference and to improve the sound quality. AUDIO SETUP CUSTOMIZE VIDEO AUDIO SETUP THEATER CURSOR MENU Ba s s Tre b le Ba la n c e Re s e t Ad v a n c e d Se ttin g s Menu CUSTOMIZE VIDEO AUDIO THEATER SEL SEL To M e n u B a r 50% 50% To Q u i t CURSOR Exit Bass Tr ebl e B al anc e Res et A dv anc ed S etti ngs Menu To M e n u B a r 90% 50% To Q u i t Exit Use CURSOR or to highlight the function to be adjusted.
AUDIO AUDIO ADVANCED SETTINGS Use ADVANCED SETTINGS to improve the sound performance of your TV, depending on listening conditions.
THEATER THEATER THEATER Use this function to choose picture and audio settings for a true home THEATER experience. THEATER MODES Use this function to choose from automatic picture settings to optimize your TV’s performance.
THEATER THEATER The following surround settings will reproduce the “live” sound you would hear in concert halls, sports stadiums, movie theaters, etc. with only two speakers.
CARE OF YOUR HITACHI PROJECTION TV AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Place your television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your television will not be used for a long period of time, for instances, when you go on vacation.
RECEPTION PROBLEMS • IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception.
rd cor is p TV rec lug t is s ge wit d an che in oth d''O er N" cha Ch nn eck el ( an sta ten tion na Ch tr o eck con ub ne an le) ctio ten ns na Ch (ba for eck ck bro ou of T ken tsid V) Ch lea ea eck d-i nte nw nn for a ire loc al i Ad nte jus tC r fe ren on t r ce ast Ad jus con tB tr o rig l htn Ad ess jus con tC tr o olo l rc Ad on jus tr o tT l int con Ad tr o jus l tV olu me con tr o l ure No Picture, no sound Try SYMPTOMS CH TR ECK Y T TH HE ES Be SE E I sur AD TEM ee xte JU Be rna ST S
USEFUL INFO Features: • • • • • • • • • • • • • • • • • • • • Superfine Picture Quality 1280 Line Horizontal Resolution Pure Green and Red Filter Lenses PERFECT PICTURE System Mulit-Picture-In-Picture with freeze. Remote (Controls many VCR brands, cable boxes and DVD players.
USEFUL INFO e c i v r e s To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day 800 HITACHI (1-800-448-2244) Hitachi America, LTD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
NOTES 66
NOTES 67
QR52481