Instructions for use 32LD8700TU GB
Contents Remote Control Buttons ....................... 2 LCD TV .................................................... 3 Preparation ............................................. 5 Source Menu ...................................... 24 Sound in PC mode ............................. 24 Other Features ..................................... 24 TV Status ............................................ 24 Mute Indicator ..................................... 24 PIP and PAP modes ...........................
= Stand by On/Off Remote Control Buttons = Program Information SEL= Select TV/ DVD /SAT AV3 = AV3 mode AV2 = AV2 mode RGB2 = No Function RGB1= PC mode = Go back to previous menu `= Cursor Right OK = Enter b =Cursor Down = Picture Mode P+/ - = Programme Up/ Down = Mute On/Off 0 - 9 = Digit buttons = PIP / PAP / TV BLUE = Only used in Teletext mode YELLOW = Only used in Teletext mode = Reveal P- = Programme Down / SLIDE SHOW/ = No function/ Subtitle PHOTO= No Function SWIVEL= No Function = Aspect rat
LCD TV FRONT VIEW REAR VIEW -3-
Audio Line Outs TV/AV button Subwoofer Out MENU button Prog. Up, Prog.
Preparation For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Use this apparatus in tropical and/or moderate climates. Features Remote controlled colour television. Fully integrated Digital TV (DVB-T) 100 programmes from VHF, UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system.
stallation of an extension lead, please consult a competent electrician. DONTs DONT continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way switch off, withdraw the mains plug and consult your dealer. DONT place water filled vessels on top of T.V. cabinets. DONT remove any fixed cover as this may expose dangerous voltages.
6.Heat and Flames The set should not be placed near to naked flames and sources of intense heat,such as an electric heater. Ensure that no naked flame sources, such as lighted candles, are placed on top of the set. The mains plug is used to disconnect the TV from the mains and therefore it shall remain readily operable. Warning: To prevent injury, this device must be securely attached to the floor/wall in accordance with the installation instrutions. 7.
Before Switching On Your TV Power Connection IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Connections To The Aerial Input Socket NOTE: Remove the batteries from remote control handset when it is not to be used for a long period.Otherwise it can be damaged due to any leakage of batteries.
Initial Settings When the TV is turned on for the first time, it is in the digital mode. Because this is the first time the TV is used, there are no channels stored in the memory and the following message appears on the screen. To start installation process, select Yes, to cancel select No. To select an option Yes or No, highlight the item by using or buttons and press the OK button.
Programme Selecting Operating The TV You can operate your TV using both the remote control handset and the buttons on the set. (Previous or next programme) Operating with the buttons on the TV set Press the P+ button to select the next programme. Volume setting and programme selection can be made by using the buttons on the control panel at the right side of the TV. Press digit buttons on the remote control handset to select programmes between 0 and 9.
Channel List is the place where the channels are managed. Press the OK button to delete the highlighted channel in the channel list. Then the following message appears on the screen. Press or button to highlight the desired option. If OK button is pressed while Yes is highlighted, the highlighted channel is deleted. Selecting No cancels the delete operation. Renaming channels Navigating the whole channel list or button for selecting the previPress ous or next channel.
Select the channel to be locked by highlighting it and select the Lock option by pressing or button. When the OK button is pressed, a password box is displayed. On Screen Help Pressing INFO Button For all menus press the button to display the help information about the menu functions. For Channel List menu the following message is displayed on the screen. Enter the password using the digit buttons on the remote control. The Lock icon will now be displayed next to the selected channel.
OK button in the auto-search pop up menu. All the services are searched and a channel table is created automatically. All channels found are stored in a sorted form with respect to their channel numbers. Some services may not appear with the correct channel number. At the time of printing, not all broadcasters are sending their channel number information. Press the OK button to search for analogue channels.The following menu appears on the screen for analogue channel search.
Favourite Mode This function enables or disables the favourite channel list mode. See Channel List menu Favourites on page 12. The various configuration functions are displayed in a list, along with a quarter-screen image of the currently selected channel. You can select a function by highlighting the coror butresponding menu line using the ton. or button to turn on/off favourite Use mode.
Both automatic upgrade methods result in standby mode either upgraded or not. If the automatic upgrade is set to Disabled then this function will not work. Search For New Version (Manual upgrade) Manual upgrade starts if the Search for New Version item is highlighted by using or button and activated via pressing the OK button. After Search for New Version is activated, the IDTV tunes to each frequency that have been stored in its database and looks for the new software.
To set an event, highlight its mode button or button and press the OK using the button to display the timer entry window. Here the five settings of channel name, start time, end time, date and frequency mode can be set. You can move freely between each setting using the or buttons. Language Some programmes are broadcast in two or more languages simultaneously. The language heard can be selected from the Language Menu.
Detailed information about Sound, Picture and Feature menus are in AnalogueTV Menu System section on page 17. 3. Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. Common Interface Some CAMs may require the following set up. Please set the CAM by entering the IDTV menu, Common Interface then pressing the OK button. (CAM set up menu is not displayed when it is not required.
Mode By pressing a / b button, select Mode. Press _ / ` button to choose one of these options: Natural, Dynamic and Cinema. Picture mode can be changed directly by pressing the button. Contrast By pressing a / b button, select Contrast. Press ` button to increase contrast. Press _ button to decrease contrast. Contrast level can be adjusted between 0 and 63. Brightness By pressing a / b button, select Brightness. Press ` button to increase brightness. Press _ button to decrease brightness.
Equalizer By pressing a / b button, select Equalizer. Press _ / ` or OK button to enter equalizer menu. Sound Mode In equalizer menu the sound mode can be changed to User, Pop, Rock, Jazz, Flat and Classic by pressing _ / ` button. Equalizer menu settings can be changed only when Sound Mode is User. Select the desired frequency by a / b button and increase or decrease the frequency gain by pressing _ / ` button. Press the menu.
mended to select High if listening at high volume levels. There is a subwoofer output that can accept an active subwoofer if you wish to create very high levels of Bass. Child Lock 3DS The child lock feature can be set by _ / ` button to either on or off. When off is selected, there will be no difference in the operation of your TV. When on is selected, the TV can only be controlled by the remote control handset.
Menu Background Colour System By pressing a / b button, select Menu Background. You can change menu background to Translucent or Opaque by pressing _ / ` button. By pressing a / b button, select Colour System. Press _ / ` button to change the colour system to PAL, PAL60, SECAM or AUTO. Menu Timeout Note: In EXT mode, you can choose NTSC 3.58 and NTSC 4.43 as well. By pressing a / b button, select Menu Timeout. Press _ / ` button to change menu timeout to 15 sec, 30 sec or 60 sec.
Program menu APS (Automatic Programming System) By pressing _ / ` button, select the fifth icon. Program menu appears on the screen. When you press the BLUE button for APS, the following warning screen will be displayed. By moving the cursor in four directions you can reach 20 programmes in the same page. You can scroll the pages up or down by pressing the navigation buttons to see all the programmes in TV mode (except the AV mode). By cursor action, programme selection is done automatically.
Select Autoposition item by using a / b buttons. PC Mode Installation Press ` or OK button. Power off both Computer and Display before making any connections. Warning: Auto position adjustment recommended to be done with the full screen image for the proper adjustment. Set your PCs resolution correctly before connecting to the TV. See the table on page 32 for supported modes. Use a D-SUB cable to connect the TVs PC input to the computers RGB output terminal.
Other Features TV Status Programme Number, Programme Name, Sound Indicator and Zoom Mode are displayed on the upper right side of the screen butwhen a new programme is entered or ton is pressed. Mute Indicator Contrast, Brightness and Colour Temperature adjustments in this menu are identical to adjustments defined in TV picture menu. It is placed in the upper left side of the screen when enabled. To cancel mute, there are two alternatives; When Colour Temp is Manual, you can also adjust the R,G,B items.
the screen. The active window can be changed by pressing the _ / ` button. Source restrictions of PAP Mode are same as in PIP Mode. It is not possible to show 2 different channels from the TV tuner at the same time. 16:9 Zoom: This zooms up the wide picture (16:9 aspect ratio) to the full screen. Freeze Picture You can freeze the picture on the screen by button. At PIP and PAP laypressing the outs; only the main picture can be frozen.
To Select A Subcode Page Teletext Teletext is an information system that displays text on your TV screen. Using the Teletext information system you can view a page of information on a subject that is available in the list of contents (index). Subcode pages are subsections of long Teletext pages that can only be displayed on the screen one section at a time. Select the required Teletext page bypressing button.
the requested page into memory after finding it. Press the a button to move the Teletext screen forward one page at a time. Press the b button to move the Teletext screen backward one page at a time. For Fastext The subject-heading for the information may have a particular colour. Press an appropriate RED, GREEN, YELLOW or BLUE button in order to reach the relevant page quickly. For TOP text TOP text mode of operation will be activated automatically according to the transmission.
Playback NTSC To Connect To S-VHS Input To use this option you can; Connect your camera or camcorder S-VHS input at the rear side of the TV. Connect an NTSC VCR player to a Scart socket at the rear side of the TV. Connect an NTSC VCR player to RCA Jacks at the rear side of the TV. Copy Facility Connect your equipment to the TV via S-VHS input and audio inputs of AV inputs by using S-VHS cables. Connect The Decoder To The Video Recorder Source selection for VCR recording. Select Feature menu.
Aerial Connection Connect Peripheral Equipment - 29 -
Sound Tips You can not hear any sound. Did you per- Care Of The Screen Clean the screen with a slightly damp, soft cloth. Do not use abrasive solvents as they may damage the TV screen coating layer. Poor Picture Have you selected the correct TV system? Is your TV set or house aerial located too close to non-earthed audio equipment or neon lights, etc.? Mountains or high buildings can cause double pictures or ghost images.
Specifications TV BROADCASTING PAL SECAM B/G D/K K' I/I' L/L' RECEIVING CHANNELS VHF (BAND I/III) UHF (BAND U) HYPERBAND CABLE TV (S1-S20/ S21-S41) NUMBER OF PRESET CHANNELS 100 CHANNEL INDICATOR On Screen Display RF AERIAL INPUT 75 Ohm (unbalanced) OPERATING VOLTAGE 220-240V AC, 50 Hz. AUDIO German+Nicam Stereo DTT Specifications MHEG-5 ENGINE compliant with ISO / IEC 13522-5 UKengine Profile1 Object carousel support compliant with ISO/ IEC 135818-6 and UK DTT profile.
Appendix A: PC Input Typical Display Modes The display has a maximum resolution of 1366x 768, vertical sync. frequency range of 56-85 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes.
Appendix B: DVD Player Selection You can use this remote control to operate the selected brand of DVD player by pressing the following buttons on the remote control simultaneously. Example To operate HITACHI DVD player, press and hold the INFO button, followed by the 1 button. Note: Not all models of the listed brands can be operated using this remote control. Note: Slide Show, Photo, Swivel and Rotate buttons have no function.
Appendix C: DVD Player Selection (continued) Set up hint: Example) HITACHI DVD To operate HITACHI DVD player, press and hold the button, followed by the button. 1. Set up the maker. Press button to indicate the DVD LED on the remote control. Whilst the DVD LED is flashing, press and . 2. Set up the maker type. Release the Then, press the button whilst keeping button depressed. button. 3. Confirm the setting.
Appendix D: Main and PIP-PAP Picture Combinations - 35 -
UK Guarantee Your Guarantee of Excellence Thank you for purchasing this Hitachi Television.
QUICK GUIDE GB 32LD8700TU IMPORTANT - If placing TV into cabinet or alcove, ensure there is at least a 100mm (10cm) gap to the sides, rear and top of the TV. This is to allow for adequate ventilation during operation. Please read the main Users Guide for more safety information before installation. insert the batteries into your handset either connect the aerial straight to your TV... Scart 1 Aerial (RF) Lead Scart 2 wall socket Aerial (RF) Socket ...or connect the aerial through a VCR...
...or through a satellite decoder... GB TFT-LCD TV Aerial RF Lead from Satellite to TV • Scart Lead to AV-1 on TV. TV VCR ANT.IN RF Lead to Aerial Satellite LNB lead ...or through a VCR and satellite decoder. TFT-LCD TV RF Lead from VCR to TV RF Lead from VCR to Satellite Aerial • Scart Lead to AV -1 on TV. TV VCR ANT.IN RF Lead to Aerial Satellite LNB lead ANT.
connect the TV plug to the mains socket GB UK plug European plug Powe r C ord Po wer o n/off Input button Plug the mains lead into the TV... insert plug... ...and switch on insert plug... switch your TV on by pressing the On/Off button TV/ AV MENU P/ CH Front View NB: When the set is first switched on, the set will be in standby and the indicator on the front of the set will illuminate red. Press the channel up down (P- , P+) or numeric buttons (1, 2, 3, ...) to operate.
GB important note before starting Auto Setup If you have a Video Cassette Recorder or a Satellite receiver connected to your TV please ensure that they are switched on before automatic tuning begins. In the case of a VCR, insert a pre-recorded tape and begin playback of your equipment. These measures ensure that all your external equipment is tuned in during the Auto Setup procedure. start A.P.S. (Auto Programming System) 1 Please ensure aerial is plugged in.
Installation Of The TFT TV To The Wall *% 1- To install the TFT TV on the wall, first of all, foot assembly should be removed. (Figure 1). Unscrew the 6 screws (M4 x 12) that attach the foot assembly to the TFT panel and remove the foot assembly from the TFT panel. 2- Decide the place on the wall where the TFT panel would be placed. Fix the wall mounting stencil on the wall. The stencil is used for placing the wall hangers on the wall, properly.
-2- *% Attention: Only the original wall bracket should be used with this product ),*85(
Hitachi Ltd. Consumer Business Group Shin-Otemachi Bldg 5f, 2-1, Otemachi 2-Chome, Chiyoda-Ku, Tokyo 100-0004 Japan HITACHI EUROPE LTD. Consumer Affairs Department PO Box 3007 Maidenhead Berkshire SL6 8ZE HITACHI EUROPE S.A. 364, Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens UNITED KINGDOM Tel: 0870 405 4405 Email: consumer.mail@hitachi-eu.com Tel: 1 - 6837200 Fax: 1 - 6835694 Email: dmgservice.gr@hitachi-eu.
