Instructions for use 22LD4500 GB
Contents Wiring The Plug ........................................... 2 Remote Control Buttons ............................. 3 Control Panel ............................................... 4 Preparation ................................................. 6 Features ................................................... 8 Safety Precautions ..................................... 9 Before Switching on your TV .................... 11 Power connection ................................... 11 Aerial Connections ........
wiring the plug If your TV is fitted with a non-rewireable plug and you need to change the fuse, you will need to refit the fuse cover. If you lose or damage the fuse cover, do not use the plug until you have replaced the cover with a new one. You can get one from us. Make sure you replace the fuse cover with one which is the same colour as the markings on the fuse.
remote control = Stand By = Cursor Up 1 = Cursor Right OK / SELECT = Okay (Store) INFO= Info (Program Menu) 2 32 3 0 - 9 = Direct Program -/-- / EXIT = Double Digit =Previous Programme P/CH + = Programme Up 31 30 4 M OK 5 + = Volume + DTV / TV = TV / DTV mode 1 2 3 = External Source (AV-1, AV-2, AV-3, S-VIDEO, PC) 4 5 6 7 8 9 Yellow (FEATURE) = Feature Menu Blue (INSTALL) = Installation Menu 29 = Hold = PAP AP / GUIDE = Index Page = Reveal, PC = Switch from TV to PC = Expand, WIDE
Control Panel - VOLUME + - VOLUME + - P/Ch + - P/Ch + MENU TV/AV POWER MENU TV/AV SPEAKER LED INFRARED RECEIVER PC IN PU T D C 15 V PC AU DIO A NT. 75 W 2/ 1/ FOOT TOP COVER 4 1549 UK-IDTV TV-DVB-22'' TFT IB-2-(Revised -419x27).p65 01.12.
PC N I PUT DC 15V PCAUDIO ANT.7 5 W 2/ 1/ S-VHS PC INPUT A B C D E F DC 15V PC AUDIO 2/ ANT. 75 W 1/ PC INPUT DC 15 V PC AUDIO INPUT AERIAL SCART SOCKET 2 (AV-2) G HEADPHONE H AUDIO INPUT (L) I AUDIO INPUT (R) J VIDEO INPUT SCART SOCKET 1 (AV-1) K (AV-3) S-VIDEO INPUT 5 1549 UK-IDTV TV-DVB-22'' TFT IB-2-(Revised -519x27).p65 01.12.
Preparation Install Display on solid horizontal surface such as a table or desk. For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Installation of device on the wall Step1: Invert the flat monitor screen and placed it on a flat surface. Remove the foot top cover. Remove the back support from the screen.
1549 UK-IDTV TV-DVB-22'' TFT IB-2-(Revised -719x27).p65 Mounting bracket LCD MONITOR 3-) D=4mm x L=10mm screws 2-) L=32mm x D=5mm screws Wall bracket 1-) D=4mm x L=10mm screws WALL STRUCTURE 2-) Plastic anchors preparation 7 01.12.
preparation Place TV on a solid surface. For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Use this apparatus in tropical and/or moderate climates. Features • Remote Controlled Colour television and PC Monitor. • Fully integrated Digital TV (DVB-T) • 100 programmes from VHF, UHF bands or cable channels can be preset. • Controlling the TV is very easy by its menu driven system.
Safety Precautions IMPORTANT SAFETY INFORMATION ON OPERATING YOUR TV Do’s and Don’ts DO’s This Television has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment. DO consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
1. Power Source 8. Servicing The TV set is designed to operate on 15 V DC. The adaptor should be operated from a 220-240V AC, 50 Hz. outlet. Ensure you select the correct voltage setting for your convenience. Please refer all servicing to qualified personnel. Do not remove cover as this may result in electric shock. 2. Power Cord The power supply cord should be placed so that it is not likely to be walked on or pinched by items placed upon them or against it.
Before Switching on your TV Before Switching on your TV How to connect other devices IMPORTANT: Switch off the TV before connecting any external device. Sockets for external connections are at the back of the TV. For connection of other devices via Euroconnector refer to the manuals of the related devices. Power connection PC I NPUT D C15V PC AU DIO ANT. 75W 2/ 1/ AC adapter To POWER INPUT DC 15 V termi nal IMPORTANT: The TV set is designed to operate on 15 V DC.
Switching the TV ON/OFF To switch the TV on: Your TV will switch on in two steps: 1- Connect the power supply cord to the system. Press the “POWER” button at the top of the TV. Then the TV switches itself to stand-by mode and the led becomes red located on the front of the TV.
preparation SILENCE MODE: "When you turn off your IDTV by pressing Stand-by key (on RC) , IDTV switches into SILENCE mode and the led on the front of IDTV starts blinking. Also, IDTV switches into SILENCE mode automaticallly everyday at 3.00 a.m. In the silence mode IDTV searches for a new software. If a new software is found, it is loaded onto the old s/w without any warning message. TV exits from stand-by mode after loading process.
preparation After Automatic search is finalized the following menu appears. Do you want to search for analogue channels ? Yes No If you select “Yes” Warning All Prestored Programmes Will Be Erased Country Language Continue Cancel A.P.S. Is Running Please Wait After A.P.S. is completed program table is displayed on the screen. See the “Programming” menu in terrestrial TV section.
everyday operation There are a great many keys to use in different situations. Many of the menu screens displayed by the TV have reminders as to which keys do what, at the base of the screen. In addition, many screens have further help available which is displayed when the “ INFO” key is pressed, as prompted at the bottom right of the screen.
everyday operation INFORMATION BANNER Whenever you change channel, using the “P/CH+” and “- P/CH” keys or the number keys, the TV displays the channel picture along with an information banner at the bottom of the screen. This will remain on the screen for approximately three seconds. The information banner can also be displayed at any time while watching TV by pressing the “ INFO” key on the remote control. Pressing the “ INFO” key again removes the banner.
everyday operation If the selected channel is locked (see Advanced operation- Channel protection), you must enter the correct four digit code to view the channel. Alternatively, the “P/CH+“ or “- P/ CH” keys are used to move to another, unlocked channel. * CHANNEL LIST You can also select the required channel directly from the on-screen channel list. First bring up the menu with the “M” key on the remote control handset.
everyday operation Hint From the Channel List screen, it is Here, you can preview any channel stored by the TV before viewing it full screen. The complete list of channels is displayed in pages of 10 channels at a time, with their channel list number and a favourite channel icon if appropriate. (see Advanced operation-Favourite channels). The name and a quarterscreen image of the channel last viewed is displayed on the upper right of the screen.
everyday operation CURRENT PROGRAMME The channels are listed at the bottom of the screen, each with the 'current event' (the name of the programme showing at that time) and the 'next event' (the following programme). When the EPG screen is first displayed, the channel last watched is highlighted in the list of channels. A quarter-screen image of this channel is displayed at the upper right of the screen along with the channel name and channel list number.
everyday operation NEXT PROGRAMME While the EPG screen is displayed, Hint If the programme details text for the current or next event is too long to fit into the text window on the EPG screen, a scroll bar appears on the right hand side of the window and the text can be scrolled up or down using the “YELLOW” and “BLUE” keys on the remote control. Using “Red” or “Green” keys will display the next/previous 5 channels in the list.
everyday operation SOUNDTRACK LANGUAGE Some programmes are broadcast in two or more languages simultaneously. The language heard can be selected from the Language Menu. Press “M” key to display the Main Menu and use the “ “ or “ ” keys to highlight the Language line and press “SELECT” key. Use the “ “ or “ ” keys to highlight the soundtrack language required and press “SELECT” key. Normal viewing, with the required language soundtrack, can be resumed by pressing the “M” key.
everyday operation DIGITAL TELETEXT Many digital terrestrial television channels not only broadcast pictures and sound for programmes but also pages of information on the programmes, the weather, news and many other topics. Some channels are entirely given over to digital teletext and carry no normal TV programme at all. These dedicated digital teletext channels will not give a quarterscreen image in the EPG or the Channel List screen.
everyday operation SUBTITLE Subtitle key Shows/hides subtitles of channel. When the subtitle key is pressed, subtitle ON/OFF message is displayed. DTV / TV KEY If there is no connected VCR device, The DTV/TV key is used to toggle TV and DIGITAL TV modes. When the IDTV is in TV mode, the TV scart is not switched and the TV operates in analog mode. TIME ( When the IDTV is in DIGITAL TV mode, this time the TV scart is switched on and the TV is switched to AV/RGB mode.
advanced operation CONFIGURING YOUR TV The Configuration menu screen is accessed from the Main Menu. Press the “M” key to display the Main Menu and the “ ” key twice to highlight Configuration, then press “SELECT” key to display the Configuration menu screen. i The various configuration functions are displayed in a list, along with a quarter-screen image of the currently selected channel. You can select a function by highlighting the corresponding menu line with the “ “ or “ ” keys.
advanced operation SUBTITLE: Selecting subtitle language other than “Off” will activate the subtitle language. When the subtitle language is activated, subtitle will be displayed on the screen if any matching subtitles are available. Digital teletext and subtitles can not be activated at the same time. When you set the subtitle language from the configuration menu and try to activate digital teletext by ” or colour buttons the following message appears.
advanced operation IDTV UPGRADE The IDTV can be upgraded via the configuration menu, entered from the main menu. In the configuration menu, there is the "IDTV Upgrade" button. Upgrade process can be started by pressing this button. There are two possibilities for IDTV software to be upgraded: automatic and manual. Automatic upgrade can be enabled or disabled by pressing “ “/“ ” buttons. If it is enabled, then there are two ways for automatic upgrade.
advanced operation IDTV returns to the configuration menu if there is no new software. Software Upgrade Completed searching for upgrade. No new sotware was found. If there is a new software, pressing "Yes" will cause upgrading to be started. By, pressing "No" user can return to the configuration menu. New software found! Upgrade? Yes No Loading will be displayed on the screen by a message and a progress bar, together with a percentage button will indicate the status.
advanced operation 75% After loading the software into memory, it will be written permanently. This situation will be shown displaying a message. When the upgrade is finished a message box indicating this will appear and the IDTV will go to standby in order the changes to take place. 28 1549 UK-IDTV TV-DVB-22'' TFT IB-2-(Revised -28 19x27).p65 01.12.
advanced operation 29 1549 UK-IDTV TV-DVB-22'' TFT IB-2-(Revised -29 19x27).p65 01.12.
advanced operation EDITING THE CHANNEL LIST The digital terrestrial television channels found by the TV when first installed are stored in its memory as a channel list. This list can be altered and amended to remove unwanted channels and to suit your own preferences. First bring up the Main Menu with the “M” key on the remote control handset.
advanced operation SELECT This function selects a channel for viewing and is an alternative to using the “P/CH+” and “- P/CH” keys, channel number or EPG. Highlight the channel to be viewed, highlight the “SELECT” button at the base of the screen using the “ “ or “ ” keys and press “SELECT” key. The highlighted channel now appears in the image window and you can leave the Channel List to view the channel by pressing “M” key.
advanced operation CHANNEL AND MENU PROTECTION CHANNEL LOCK Some channels broadcast material which you do not want younger members of the family to watch. Any channel can be 'locked' so that it cannot be selected for viewing without first a four-digit PIN code being entered. In this way any channel not suitable for younger viewers can be protected. The channel lock is applied with the Channel List menu.
advanced operation MENU LOCK Simply locking a channel will not deflect a determined would-be viewer. Re-installing the complete channel list, for example, will bypass the channel lock. However, the menus can be locked out of use too, to prevent this. Display the Main Menu by pressing the “M” key, highlight Configuration, and press “SELECT” key to display the Configuration menu screen.
advanced operation FAVOURITE CHANNELS There will be some channels that you tend to watch more often and some only occasionally. Although some duplicate or scrambled channels you may want to delete from the channel list, others although not watched frequently, you will not want to do away with altogether. The favourite mode allows the most-watched channels to accessed more easily, leaving the less-watched channels accessible but out of the way.
advanced operation A channel can have its favourites status removed by repeating this procedure, to remove the icon. Leave the Channel List menu by pressing “M” key. Once the required channels have been marked as favourite channels, the favourite mode can be activated to allow easy access to them. Press the “M” key to display the Main Menu, the “ ” key twice to highlight Configuration, and press “SELECT” key to display the Configuration screen.
advanced operation EVENT TIMER You can also set a timer to switch the TV to any channel without your intervention. This is intended for making video recordings of programmes when you are out. If a single programme is to be recorded, the TV can be left switched to the required channel and the timer set on the VCR. However, if two or more programmes on different channels are to be recorded then the timer is set as well, to select the required channel when it is needed.
advanced operation Hint If an invalid number for the start or end times or the date is entered, “Entered time is not valid.” message is displayed on the screen. Pressing “M” or “SELECT” key returns to the Timer screen with the settings in place in the timer event list.
RE-INSTALLATION Although your TV will not lose its settings or stored channels when switched off, you may wish to re-install the TV because you have moved to a different area with different broadcast frequencies, you wish to reinstate a channel previously deleted from the channel list, or you want to watch new channels which have started broadcasting.
advanced operation FIRST TIME INSTALLATION To reset the TV, highlight the First Time Installation line in the menu and press “SELECT” key. A warning screen is displayed in case of accidental operation. Highlight the YES button with the “ “ or “ ” key and press “SELECT” key to erase all the channels and settings and switch the TV to standby. You can now start again as detailed in Preparation - Tuning In.
advanced operation AUTOMATIC SEARCH Channels: Codec 4:3 Codec 16:9 BBC ONE BBC TWO BBC CHOICE BBC NEWS 24 BBCi BBC PARLMNT BBC Knowledge Searching UHF Channel: 49. Please wait. This will take a few minutes. 0% 100 % MENU Cancel Search If, alternatively, from the search options menu the Manual Search line is highlighted and “SELECT” key pressed, the manual search screen is displayed. This is for searching for digital channels on a single broadcast frequency.
HINT Depending on the reception conditions in your particular area, If no digital terrestrial television broadcasts are found the IDTV will display a message: you may find that the list of channels found includes one or more repeated names. This is because the IDTV may detect and store some channels, including those it cannot receive clearly, from adjacent areas alongside the strong channels from a transmitter nearby. This is not a problem and the weaker channels can be deleted from the IDTV later.
advanced operation COMMON INTERFACE MENU Common Interface Menu is entered from the Main Menu when the Common Interface button is selected by the user. Just after the selection, a new menu appears on the TV including the names of the common interface modules inserted to the slots. If there is no module inserted into the slots, common interface button on the main menu is disabled by the system. The MediaGuard names are selected for demostration so you may see different names on this Common Interface menu.
advanced operation Profile1 Modules display three types of items on the TV monitor. 1) Module Menu (Figure 4) 2) Inquiry Box (Figure 6) One of them is the Module Menu as you can see an example of this type in Figure 4 Also the common interface module can display a list of items (channel list, subscription information, module information etc.) and an inquiry message for pin control, changing module ratings etc. You can see List box and Inquiry box taken from the Viaccess module.
advanced operation Common Interface Please, enter your PIN code ??? Figure 6. Module Inquiry (this list is identical for the Viaccess Common Interface Module) LANGUAGE Digital terrestrial television channels can broadcast simultaneous soundtracks in more than one language. This function selects which language soundtrack you will hear when switching to a channel broadcasting with multiple soundtracks. The Language menu screen is accessed from the Main Menu.
Operating the TV You can operate your TV both using the remote control handset and onset buttons. Operating with the buttons on the TV set Volume setting and programme selection can be made by using the buttons at the control panel on the top of the TV. Volume Setting +” key to increase volume. Press “Press “ ” key to decrease volume. A volume level scale (slider) will be displayed at the middle of the bottom on the screen.
1 2 3 4 5 6 7 8 9 0 Menu System Your TV has been designed with a menu system to provide an easy manipulation of a multi-function system. The TV is controlled by choosing the commands, which are displayed on the screen. Press the "M" key. The main menu will be displayed at the middle of the screen. Menu Sound Menu To change sound settings • Enter the Sound Menu directly by pressing the Red key or, • As you enter the main menu, sound will be the first item.
Sound Sound On To Change Headphone Sound Settings Selecting Sound Mode • Using “ ” or “ ” key select Sound Mode. • Press “ ” or “ ” key to change Sound Mode. You c a n c h o os e M o n o , S t e r e o o r D u a l (I-II) mode, only if the selected channel supports that mode. You can also change sound mode directly pressing “I-II” button on your remote control. • Using “ ” or “ ” key select Headphone. • Press “ ” or “ ” key or directly press “OK” key on Headphone, to enter the Headphone menu.
In case of bilingual broadcast, you can select original or dubbed language again using mode menu. So when somebody listens to the original language from the loudspeakers, somebody else can listen to the dubbed language from headphone. To Store the Settings the value, or “ ” key to decrease the value. In mid position, cursor is displayed with one arrow. To store the Equalizer settings, press “ ” or “ ” key or directly press “OK” key on “Store” option.
Picture Menu Setting Colour • To enter the Picture menu directly, press the Green key, or • Press "M" key, now you are in main menu. In the Main menu, select “Picture” using “ ” or “ ” key,, then enter the Picture menu pressing “ ” / “ ” or “OK” key. • Using “ ” or “ ” key select Colour.. • Press “ ” key to increase colour level. • Press “ ” key to decrease colour level. Picture Menu Setting Brightness Setting Sharpness • As you enter the picture menu, Brightness will be the first item.
Setting Noise Reduction To Store the Settings • Using “ ” or “ ” key select Noise Reduction. • When the cursor is on any item which has no submenu press “OK” key on the remote control to store the settings directly. or, • Press “ ” or “ ” key to select Noise Reduction level “Off” or “Minimum” or “Medium” or “Maximum” then select “store” and press “ ” or “ ” key to save your setting. No te 1 : • Press “ ”, “ ” or “OK” key on Store option to store Picture menu settings.
Feature Feature Off TV Once the time set with the sleep timer has elapsed, the set will go to standby. Child Lock You can use this feature to prevent children turning on/ off TV or changing programmes or adjustments etc. without remote control. The Child Lock feature can be set On or Off by “ ” or “ ” key. When Off is selected, there will be no difference in the operation of your TV. When On is selected, the TV can only be controlled by the remote control handset.
Selecting Programme Selecting Fine Tuning To select programme number, you can use “ ” or “ ” key, Digit Keys or The Double Digit key with digit keys. You can use the Fine Tuning process for fine adjustment (after coarse adjustment), if you are not happy about the image on the screen. Install. Use “ ” or “ ” key on Fine Tuning item, until get-ting the best image on the screen. Normally the Fine Tuning cursor is placed next to the left side on the slider and this is indicated with one arrow.
Menu Moving cursor to four direction you can reach 20 programmes in the same page. By scrolling the pages up or down by pressing the navigation keys you can select all the programmes in TV mode (except the AV mode). By cursor action, programme selection is done automatically. It is also possible to select programme by using digit or double-digit button. In this way programme selection is also automatic. The TV Status is changed by the programme selection too.
Autostore: To enter Autostore menu, press the blue key. To learn the features of this function see "Autostore" below. Autostore, searches and stores all channels automatically on your TV, according to the transmission of programme systems in your area. In main menu, firstly use “ ” or “ ” key then use “ ” / “ ” or “OK” key to enter Source menu. In source menu, move the cursor by “ ” or “ ” key and then press “OK” key or “ ” or “ ” keys when the cursor is on the required item.
To Store the Settings Personal Preferences (PP) • When the cursor is on any item which has no submenu press “OK” key on the remote control to store the settings directly. or, All the preset values will be restored, when pressing "PP" key. •Press “ ”, “ ” or “OK” key on Store option to store PIP Picture menu settings.
Picture Mode No-Signal Detection (PC) Picture mode OSD is displayed when “ WIDE” key is pressed. Picture mode can be changed to Auto, 4:3, 16:9, Cinema, Subtitle, Zoom or WIDE” key.. Panorama by pressing “ If no valid signal detected for 5 minutes system goes to Stand-By mode. To switch on the system press Sleep Timer Indicator It is displayed on the upper right of the screen when a new programme is entered by digit key or by pressing “P
PC MODE Installation • Power off both Computer and Display before making any connections. • Connect one end of the optional 15 pin signal cable to the 15 pin connector on the PC and the other end to the 15 pin socket on the TV. Sound Menu In the main menu select “Sound” using “ ” or “ ” key then enter the Sound menu pressing “ ”, “ ” or “OK” keys. The items in this menu are described at Sound menu starting page 45.
Feature PIP Picture PIP picture is displayed on the screen with “ ” key.. By pressing “OK” key, PIP window is selected and border of the PIP window becomes green. PIP position is changed by “ ” / “ ” key. There are six dif-ferent PIP positions. PIP size is decreased by “ ” key and increased by “ ” key. Three different PIP size are available. Programme in the PIP window is increased / decreased by “P/CH+” / “-P/CH” keys. AV mode is also available in PIP window. Digit keys are inactive for PIP window.
Source Menu In the Main menu, select “Source” using “ ” or “ ” key, then enter the Source menu pressing “ ”, “ ” or “OK” keys. Source Sel ec t t he avai l abl e s ourc es of TV, AV-1, AV-2, AV-3, S-Video, PC or Digital by pressing “ ”, “ ” or “OK” keys. PIP Source Menu This menu is available when the PIP displayed. In the Main menu, select “PIP Source” using “ ” or “ ” key, then select the any available source of TV,, AV-1, AV-2, AV-3, S-Video or Digital by pressing “ ”, “ ” then “OK” keys.
Teletext Teletext is an information system that displays text on your TV screen. Using the Teletext information system you can view a page of information on a subject that is available in the list of contents (index). To Select Index Page On screen display is not available in text mode. Contrast, brightness or colour control is not available, but volume control is available in text mode. To Select Double Height Text To operate Teletext • Select a TV station on which Teletext is being transmitted.
• Teletext page number will be displayed on the upper left corner of the screen when the selected page is found. • Press “ page. “ key to display the selected Teletext For Fastext The subject-heading for the information may have a particular colour. • Press an appropriate Red, Green, Yellow or Blue key in order to reach the relevant page quickly. To exit Teletext • Press “TV” or “ TV mode. ” key.
Connect Peripheral Equipment There is a wide range of audio and video equipment that can be connected to your TV. Connection diagrams at the and of this section show you where the different equipment should be connected at the back side of the TV. Via Aerial Input PC Sound Connection If the VCR is connected via aerial input it is suggested to use the Programme 0. • Connect the PC Audio output to the TFT PC Audio In socket with stereo connection cable.
Search for and store the test signal of the video recorder • Unplug the aerial cable from the aerial socket “Aerial” of your video recorder. • Switch on your TV and put the video recorder on the test signal. (See the handbook for your video recorder.) • Search for the test signal of your video recorder in the same way as you searched for and stored the TV signals. See Install, Search and Store TV channels. Store the test signal under programme number 0.
Aerial Connections Outdoor Aerial Connections VHF Aerial Round 75 ohm coaxial cable 75W VHF/UHF Rear of TV 75W Flat 300-ohm twin lead cable VHF/UHF Aerial VHF/UHF Rear of TV Round 75-ohm coaxial cable Connect Peripheral Equipment HEADPHONE CAM ERA (optional) AU DI O E X T E R N A L S P E AK E R VIDEO (o pti ona l) ANT.IN F OR S AT E L L I T E R E CE I V E R DECODER 64 1549 UK-IDTV TV-DVB-22'' TFT IB-2-(Revised -64 19x27).p65 01.12.
PC INPUT TYPICAL DISPLAY MODES The display has a maximum resolution of 1280 x 720, vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes. Mode 1 2 3 4 5 6 7 8 9 10 11 12 13 Resolution Horizontal Vertical 640 640 640 640 720 800 800 800 800 1024 1024 1024 1280 400 480 480 480 400 600 600 600 600 768 768 768 720 Frequency Hor. (kHz) Ver. (Hz) 31.5 31.5 37.9 37.5 31.5 35.2 37.9 48.
Tips / Troubleshooting Guide On Digital mode PROBLEM POSSIBLE CAUSE WHAT TO DO No Signal mode - Aerial is disconnected - Aerial is damaged/misaligned - Out of Signal area - Check aerial lead - Check aerial lead - Check with dealer No Picture or Sound - Tuned to digital teletext channel - Retune to another channel Scrambled channel message - Channel is scrambled - Select alternative channel Forgotten channel lock code - Re-install channels to cancel channel lock Forgotten menu lock code - Cont
No Image on Display Screen For TV : Is the aerial connected properly? Are the plugs connected tightly to the aerial socket? Is the aerial cable damaged? Are suitable plugs used to connect the aerial? If you are in doubt, consult your dealer. No Image means that your TV is not receiving any transmission. Have you pressed the correct keys on the remote control? Try once more.
Specifications TV BROADCASTING PAL I/I’ NUMBER OF PRESET CHANNELS 100 RECEIVING CHANNELS CHANNEL INDICATOR VHF (BAND I: CH2-4, BAND III: CH5-12) UHF (CH21-69) CABLE CHANNEL (S1-S41) Input Signal Video: Analog 0.7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Separate sync. Horizontal Timing Vertical Timing 30 - 69 KHz 50 - 75 Hz Dot Rate 78.75 MHz max. On Screen Display RF AERIAL INPUT 75 Ohm (unbalanced) OPERATING VOLTAGE For adaptor: 220-240 V AC, 50 Hz.
UK Guarantee Your Guarantee of Excellence Thank you for purchasing this Hitachi Television.
Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 –12 Nishi Shinbashi, 2 – Chome, Minato – Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD, Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA UNITED KINGDOM Tel: 01628 643000 Fax: 01628 643400 Email: consumer-service@hitachi-eu.com HITACHI EUROPE S.A. 364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens GREECE Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.