RFID Reader/Writer Unit Model: ME-KS01M48-A Hardware Manual REV 1.00 February 28, 2011 Maxell Seiki, Ltd. 2011@Maxell Seiki Ltd.
ME-KS01M48-A PREFACE This manual explains how to operate the RFID Reader/Writer Unit hardware (hereafter RW). Read this manual to learn how to connect the RW to personal computer (hereafter PC), how to operate it, how to clean it up and important cautions. (1) Specifications are subject to change without notice. For this reason, specifications may be different from the contents of this manual.
ME-KS01M48-A SAFETY For safety reasons, obey the contents of this manual. Before using this RW, carefully read this manual and use this RW correctly. Labels The meaning of each label is as follows. Label Meaning WARNING Misoperation may cause serious accident. Fatal accident or serious injury is assumed if misoperation is not evaded. CAUTION Misoperation may cause injury or property damage. Injury or property damage is assumed if misoperation is not evaded.
ME-KS01M48-A For safety reasons, read this manual before using the RW. CAUTION The safety of this RW is taken into full consideration, but if you feel danger, turn the power off immediately and contact your maintenace service company. Use the RW within specifications and use environment. Establish a ground for AC power cable to avoid an electric shock. Remove trash and dust from the power plug and insert AC power cable into the RW and an electric outlet securely. Use the RW in a room.
ME-KS01M48-A Advice Advice Clean the RW! Always clean the RW. Dust on the antenna of RW may cause read error and write error. When cleaning the RW, turn the power off to avoid an electric shock. Don’t wipe the RW with moistened dustcloth or solvent such as a thinner. It may cause an electric shock. 2011@Maxell Seiki Ltd.
ME-KS01M48-A Contents 1. Introduction .............................................................................................................................. 1 2. Exterior features ....................................................................................................................... 1 3. Connecting instructions ............................................................................................................ 2 4. Operating instructions .....................................
ME-KS01M48-A 1. Introduction This manual explains how to use this RW. Before placing and using this RW, carefully read this manual. Regarding how to operate an application, carefully read an application manual. 2. Exterior features ② ① ④ ⑤ ③ ・Body Item ① Power ② Antenna ③ USB connector ④ Outlet of power cable ⑤ Fuse Function Turn the power on or off. Reads and writes the data by setting a rack for the Intelligent Microtube. Connect the RW to the PC. USB connector: Type B Insert the power cable. T1.
ME-KS01M48-A 3. Connecting instructions Place the RW following the instructions, and then connect the RW to a PC. CAUTION TURN THE POWER OF RW OFF WHEN PLACING THE RW AND CONNECTING CABLES. 1) Place the RW on a flat and solidly-built table. CAUTION PLACE THE RW NOT TO CLOSING RW VENTS.
ME-KS01M48-A CAUTION USE POWER WITHIN THIS SPECIFICATIONS (AC 100V – 240V). PLUG THE AC POWER CABLE INTO AN ELECTRIC OUTLET THAT IS PROPERLY GROUNDED. USE AN ELECTRIC OUTLET THAT IS EASILY UNPLUGED. UNPLUG THE AC POWER CABLE FROM THE ELECTRIC OUTLET WHEN NOT IN USE. 3 Maxell Seiki, Ltd.
ME-KS01M48-A 4. Operating instructions This section explains the operation of the RW. Install a device driver and an application before using the RW. Regarding how to install and how to operate an application, read an application manual. 1) Turn the power on. When turning the power on, the switch of power shines in green. 2) Launch an application after confirming that the PC has recognized a device driver. 3) Set a rack including microtubes on the antenna of RW. Advice Don’t push the antenna of RW.
ME-KS01M48-A 5. Care and Maintenance This section explains the care and maintenance of the RW. Please clean the RW following the instructions before starting an operation. CAUTION ALWAYS TURN THE POWER OF RW OFF WHEN CLEANING. 1) Unplug the AC power cable from the electrical outlet after flipping the power switch off. 2) Wipe the antenna of RW with a dry cloth to remove trash and dust from it. Advice ● Trash and dust on the antenna of RW may cause a communication error.
ME-KS01M48-A 6. Troubleshooting Go through this section if you experience difficulty in operating the RW. Symptoms Causes The RW does not Check that the AC power cable turn on. is securely inserted into the RW and the electrical outlet. Check the specification of power supply. Check a fuse. The RW does not Check that the USB cable is work. securely inserted into the RW and the PC. Check that the PC recognizes USB devices normally.
ME-KS01M48-A 7. Specifications 1． Power supply voltage AC100V – 240V 50/60Hz 2． Power consumption 15W 3． Dimensions (RW) 280(W) x 190(D) x 166(H) mm 4． Weight (RW) Approx. 3.2kg (except cables) 5． Operating conditions 1) Ambient temperature 2) Relative humidity : 0 to 40℃ : 35 to 80%RH (no dew condensation) 6． Non-operating conditions 1) Ambient temperature 2) Relative humidity : -10 to 50℃ : 30 to 85%RH (no dew condensation) 7． Use environment Interior of room * Avoid direct sunlight, rain and dew.
ME-KS01M48-A 8. Dimensions 1. RW Unit: mm 280 190 166 12 2. Rack Unit: mm 119.05 86.25 75.45 129.55 8 Maxell Seiki, Ltd.
