Specifications

ManualsBrandsHisense Air Conditioning ManualsElectronicsWiFi module

WIFI Module

Instruction

System Operation Requirements

A. Smartphone System Requirements

The following are the minimum specifications needed to successfully run the

app on a smartphone:

Table 1 Smartphone requirements

Terminal device Android IOS

OS Android 6 or higher IOS 8 or higher

Resolution 1920*1080 or higher 960*640 or higher

Summary of content (10 pages)

PAGE 1
WIFI Module Instruction System Operation Requirements A.
PAGE 2
B. Wireless Router requirements Table 2： Wireless Router requirements Standard Frequency Range Security Output Power Data Rate Sensitivity Modulation IEEE 802.11b/g/n 2.402-2.483.5GHz 128 bits WPA-PSK/WPA2-PSK 802.11b: 11dBM(11Mbps) 802.11g: 15dBM(54Mbps) 802.11n: 11dBM(72.2Mbps) 802.11b: 11Mbps 802.11g: 54Mbps 802.11n: 72.2Mbps 802.11b: 11Mbps 802.11g: 54Mbps 802.11n: 72.2Mbps QPSK+OFDM Notice: *Please try to use a certified 2.4G wireless router.
PAGE 3
WiFi picture 1: The function of WiFi module in the intelligent home appliance system Network standard 802.11 b/g/n WiFi module parameters Work environment：-20℃-85℃ Rated voltage：DC 3.3V Maximum dissipation power：<500mA Voltage fluctuation：±10% RF Frequency Oscillator The crystal oscillator circuit is building in at WiFi module X1.
PAGE 4
Modulation：WIFI: 11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM Supported channels：1-11 Max.tune-up power with tolerance (AV value) 802.11 b mode: 12±1.0dBm 802.11 g mode: 10±1.0dBm 802.11 HT20 mode: 9±1.0dBm 802.11 HT40 mode: 10±1.
PAGE 5
WiFi module Interface Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Define GND IO14 IO15 IO0 IO12 IO5 IO19 GND GND RX0 TX0 TX1 RX1 IO22 3.3V GND Description GND PWM0 PWM1 PWM2 PWM3 PWM4 UART0_CTS,SPI1_CS,SPI0_CS,I2C0_SDA, TIMER5_TRIG GND GND UART0_RXD,SPI1_CLK,SPI0_SCL,I2C1_SCL,TIMER4_TRIG UART0_TXD,SPI1_MOSI,SPI0_MOSI,I2C1_SDA, PWM0 UART1_LOG_TXD UART1_LOG_RXD UART0_RTS,SPI1_MISO,SPI0_MISO,I2C0_SCL,PWM5 VCC 3.
PAGE 6
SAFETY Precautions This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,Science and Economic Development Canada’s licence-exempt RSS(s).
PAGE 7
DÉCLARATION D’IC SUR L’EXPOSITION AUX RADIATIONS: Cet équipement est conforme aux limites d’ exposition aux radiations définies par le Canada pour des environnements non contrôlés.Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ouun autre émetteur. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 8
Antenna information Manufacture: INNO Circuits Limited Frequency Antenna Antenna Type (MHz) 1 2412-2462 integral antenna MAX Antenna Gain (dBi) 1 Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.
PAGE 9
Notice to OEM integrator The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations.There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements.
PAGE 10
confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l'hôte.