Reference Test report no. 15009763 EUT: GX 3, GX 3-ME FCC ID: SDL-GXR01 FCC Title 47 CFR Part 15 C Date of issue: 2015-02-10 Annex acc. to FCC Title 47 CFR Part 15 relating to Hilti Corporation GX 3, GX 3-ME Annex no. 5 User Manual Functional Description Title 47 - Telecommunication Part 15 - Radio Frequency Devices Subpart C – Intentional Radiators Measurement Procedure: ANSI C63.4-2009 Date: 2015-03-13 m. dudde hochfrequenz-technik Vers. no. 1.
Reference Test report no. 15009763 EUT: GX 3, GX 3-ME FCC ID: SDL-GXR01 FCC Title 47 CFR Part 15 C Date of issue: 2015-02-10 User Manual / Functional Description of the test equipment (EUT) Date: 2015-03-13 m. dudde hochfrequenz-technik Vers. no. 1.
GX 3 Original operating instructions en
Contents 1 1.1 Information about the documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1.3 Typographic emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1.2 Pictograms . . . . . . . .
▶ Ensure that the operating instructions are with the fastening tool when it is given to other persons. Changes and errors excepted. 1.3 Type designation and serial number The type designation and serial number are printed on the type identification plate. ▶ Copy these details to the table below and provide this information when making an enquiry to your Hilti representative or to Hilti Service. Product information Type: Generation: Serial number: 01 2 Safety 2.
▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ Do not attempt to drive fasteners into materials that are too soft, such as wood or drywall/gypsum board. Attempting to drive fasteners into these materials may lead to malfunctions and fasteners being driven incorrectly or driven right through the material. Do not attempt to drive fasteners into materials that are too brittle, such as glass or tiles.
▶ ▶ ▶ ▶ ▶ ▶ Do not operate the gas can valve manually. If a person has inhaled gas, take the person into the open air and place the person in a comfortable position. Should a person becomes unconscious, bring the person into a well-ventilated area and place the person in a stable recovery position (i.e. lying on the side). If the person is not breathing, administer artificial respiration and, if necessary, supply oxygen.
3.
+ § / : · Gas can compartment cover Cooling air slots Magazine lockbutton Trigger ‚RESET‘ button $ £ | ¡ Nail pusher Belt hook Gas can status indicator Inlet/outlet valve 3.3 Fastener guide The fastener guide holds the studs or, respectively, guides the nails and, when the tool is fired, thus directs the fasteners into the supporting material at the desired position.
3.10 Gas can Note Observe the safety instructions provided with the gas can! In order to operate the fastening tool, the gas can must be inserted in the gas can compartment. The gas can status can be read from the LED display after pressing the ‚GAS‘ button. The gas can must be removed before breaks between working, before maintenance and before transporting or storing the fastening tool. 3.11 Indication of gas can status After pressing the ‚GAS‘ button, the LED display indicates the status of the gas can.
It may be used for a preliminary assessment of exposure. The declared vibration level represents the main applications of the direct fastening tool. However, if the direct fastening tool is used for different applications, with different items of equipment or accessories or is poorly maintained, the vibration level may vary. This may significantly increase the exposure to vibration over the total working period.
Note In order to drive threaded studs, the magazine must first be emptied and an adapter for driving single fasteners inserted. 5.2.2 Inserting the single-fastener adapter ▶ Insert the single-fastener adapter ( → page 12). 5.2.3 Inserting the gas can ▶ Insert the gas can ( → page 9). 6 Driving fasteners 6.1 Driving nails WARNING Risk of injury! Pressing the nosepiece of the fastening tool against a part of the body may lead to serious injury due to inadvertent firing and release of a fastener. ▶ 1. 2.
2. 3. 4. 5. Press the gas can clip to release the gas can. Remove the gas can from the gas can compartment. Fit the cap on the gas can. Close the gas can compartment cover. 7.2 Unloading the magazine 1. Pull the nail pusher back until it engages. 2. Remove all nail strips from the magazine. WARNING Risk of pinching fingers! Fingers could be pinched when the nail pusher is released. ▶ When disengaging the nail pusher, do not release it and allow it to jump forward.
8.6 Removing the support leg 1. Release the support leg engaging mechanism by pressing lightly. 2. Rotate the support leg through 90°. 3. Remove the support leg. 8.7 Fitting the support leg 1. Bring the support leg into contact with the magazine at right angles and guide it into the slot. 2. Rotate the support leg through 90° relative to the magazine and allow it to engage while applying light pressure. 8.8 Inserting the single-fastener adapter 1. 2. 3. 4. Remove the gas can.
10.3 Maintenance ▶ ▶ ▶ Check all external parts of the fastening tool regularly for damage and make sure that all operating controls function faultlessly. Do not use the fastening tool if parts are damaged or if operating controls do not function faultlessly. Have a defective fastening tool repaired by Hilti Service. 10.4 Checks after care and maintenance work ▶ Move the fastener driving depth adjustment slider to the «+» position.
Fault The tool remains compressed (nose does not extend when pressure is released). Fastener driving failure rate is too high. No fastener is driven. Possible cause The nail detector is jammed and the ‚RESET‘ button is not flush with the casing when pressed. Action to be taken ▶ Remove foreign objects from the nose area. → page 12 ▶ Release the jammed fastener. The fastener guide is not held perpendicular to the working surface. ▶ Wrong type of fastener used.
15
** Hilti = registered trademark of Hilti Corp.
