Hillstone StoneOS User Manual Hillstone SG-6000 E-Series Hardware Reference Guide www.hillstonenet.com TWNO: TW-HW-ES-EN-V5.
Hillstone SG-6000 E-Series Hardware Reference Guide Name and Concentration of Toxic or Hazardous Substances and Elements in Products Component Toxic or hazardous substances and elements Lead Mercury Cadmium Cr6+ PBB PDBE Metal parts (including fasteners) Χ O O O O O Printed circuit board assemblies and components Χ O O O O O Cables and cable assemblies Χ O O O O O Plastics and Polymers Χ O O O Χ Χ Electric components other than circuit boards Χ O O O O O O: Indicat
Hillstone SG-6000 E-Series Hardware Reference Guide Preface About This Guide Thanks for choosing the network security products from Hillstone Networks. This document is an installation guide for Hillstone devices to help you install the Hillstone device properly. This guide includes the following chapters: Chapter 1. Introduction Chapter 2. Installation Preparations Chapter 3. Installation Chapter 4. Boot and Configuration Chapter 5. Hardware Maintenance and Replacement Chapter 6.
Hillstone SG-6000 E-Series Hardware Reference Guide Table of Contents HILLSTONE SG-6000 E-SERIES HARDWARE REFERENCE GUIDE ............................................................. 1 NAME AND CONCENTRATION OF TOXIC OR HAZARDOUS SUBSTANCES AND ELEMENTS IN PRODUCTS ..................... 2 PREFACE .................................................................................................................................................................. 3 ABOUT THIS GUIDE ..............................
Hillstone SG-6000 E-Series Hardware Reference Guide Connecting the Ethernet Cable ................................................................................................................................. 38 Connecting an AC Power Cable ................................................................................................................................. 40 Connecting a DC Power Cable ..........................................................................................................
Hillstone SG-6000 E-Series Hardware Reference Guide List of Figures Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure 6 1-1：SG-6000-E6360 Front Panel .................................................................... 1 1-2: SG-6000-E6160 Front Panel...................................
Hillstone SG-6000 E-Series Hardware Reference Guide List of Tables Table 1-1: SG-6000-E6360 Front Panel Description .................................................................................................... 2 Table 1-2: SG-6000-E6160 Front Panel Description .................................................................................................... 2 Table 1-3: SG-6000-E5960 Front Panel Description ...........................................................................................
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 1 Introduction Overview Hillstone SG-6000 series product models include SG-6000-E6368,SG-6000-E6360, SG-6000-E6168,SG-6000-E6160, SG-6000-E5960, SG-6000-E5760, SG-6000E5568, SG-6000-E5660, SG-6000-E5268,SG-6000-E5260, SG-6000-E5168,SG6000-E3965, SG-6000-E3968, SG-6000-E3960, SG-6000-E3668, SG-6000-E3662, SG-6000-E3660, SG-6000-E2868, SG-6000-E2860, SG-6000-E2800, SG-6000E2300, SG-6000-E1700, SG-6000-E1606, SG-6000-E1600, SG-6000-E1100 (WLAN versio
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-1: SG-6000-E6360 Front Panel Description No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E5960, SG-6000-E5760 and SG-600-E5660 have the same front panel. The front panel consist of 4 Gigabit Ethernet ports, 4 SFP ports, 1 USB port, 1 HA port, 1 Management port, 1 Console port, 1 Auxiliary port, 1 CLR button, 4 general expansion slots and several LED indicators. The standard power supply for SG6000-E5960/E5760 is dual power supplies, and the product with single power supply is also available.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-4: SG-6000-E5560 Front Panel Description No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-5: SG-6000-E3960 Front Panel Description No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E2800 and SG-6000-E2300 have the same front panel. The front panel consists of 5 Gigabit Ethernet ports, 4 Combo ports (Ethernet port + SFP port), 1 USB port, 1 Console port, 1 CLR button and some LED indicators. Figure 1-7: Front Panel of SG-6000-E2800 Table 1-7: Front Panel Description of SG-6000-E2800 and SG-6000-E2300 No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-8: SG-6000-E1700 Front Panel Description No. Label No. Label No. Label 1 PWR: Power LED 5 PS0: Power supply PS0 LED 9 2 STA: Status LED 6 PS1: Power supply PS1 LED 10 USB: USB port 3 ALM: Alarm LED 7 e0/0 - e0/8: Gigabit Ethernet port status LED 11 e0/0 - e0/8: Gigabit Ethernet ports 4 HA: HA status LED 8 CLR: CLR button CON: Console port The front panel of SG-6000-E1600 consists of some LED indicators.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-10: Front Panel Description of SG-6000-E1100 (WLAN version) No. 1 Label PWR: Power LED No. Label 3 No. STA: Status LED Label WLAN: WLAN LED 5 ALM: Alarm e0/0 - e0/8: Gigabit Ethernet 4 LED port status LED The front panel of SG-6000-E1100 (4G version) consists of some LED indicators. 2 Figure 1-12: Front Panel of SG-6000-E1100 (4G version) Table 1-12: Front Panel Description of SG-6000-E1100 (4G version) No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-13: Front Panel Description of SG-6000-E1100 (WLAN+4G version) No. Label No. Label No. Label 1 PWR: Power LED 3 STA: Status LED 5 4G: 4G LED 2 ALM: Alarm LED 4 e0/0 - e0/8: Gigabit Ethernet port status LED 6 WLAN: WLAN LED Back Panel SG-6000-E6368, SG-6000-E6360, SG-6000-E6168 and SG-6000-E6160 have the same back panel layout.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 1-15: SG-6000-E5960 Back Panel SG-6000-E5568, SG-6000-E5560, SG-6000-E5268, SG-6000-E5260, SG-6000E5168 and SG-6000-E3965 have the same back panel. The back panel consists of 2 power supply sockets, 1 grounding screw and 1 anti-dust mesh. The standard product of SG-6000- E5568/E5560/E5268/E5260/E5158/E3965 adopts dual power supplies and it is also available in single power supply.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-14: Back Panel Description of SG-6000-E1600 No. Label No. Label No. Label 1 DC POWER: DC power interface 3 CON: Console port 5 e0/0 - e0/8: Gigabit Ethernet port 2 CLR: CLR button 4 USB: USB port 6 Security keyhole SG-6000-E1100 (WLAN version) uses the power adapter.
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E1100 (4G version) uses the power adapter. The back panel of SG-6000E1100 (4G version) has 1 power supply socket, 1 Console port, 1 CLR button, 9 Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security keyhole, and 2 SMA connectors for 4G antennas. Figure 1-21: SG-6000-E1100 (4G version) Back Panel Table 1-17: Back Panel Description of SG-6000-E1100 (4G version) No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 1-22: SG-6000-E1100 (WLAN+4G version) Back Panel Table 1-18: Back Panel Description of SG-6000-E1100 (WLAN+4G version) No. Label No. Label No.
Hillstone SG-6000 E-Series Hardware Reference Guide PS0 PS1 HA FAN LNK ACT e0/0e0/8 WLAN 4G 14 Orange/Always on The trial license has expired and there is no legitimate license installed in the system. Off The system is running normally. Green/Always on Power Supply PS0 is running normally. Orange/Always on Power Supply PS0 is running normally, but its fan has failed. Change the power supply immediately. Off Power Supply PS0 is powered off or has failed.
Hillstone SG-6000 E-Series Hardware Reference Guide Notes: The STA and ALM LEDs will both turn red when there is a boot failure caused by OS software damage. Contact your sales representative if this occurs. As the number and type of LED indicators may vary from different product models, please refer to the actual product. System Parameters The following table lists the system parameters of Hillstone devices of all models.
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E5960 SG-6000-E5760 SG-6000-E5660 SG-6000-E5568 SG-6000-E5560 SG-6000-E5268 SG-6000-E5260 SG-6000-E5168 SG-6000-E3965 SG-6000-E3968 SG-6000-E3960 SG-6000-E3668 SG-6000-E3662 SG-6000-E3660 SG-6000-E2868 SG-6000-E2860 CPU 16 4 4 1 1 1 1 1 Gigabit Ethernet ports SFP ports USB 2.0 Host port MGT port HA port Console port Auxiliary port 4 4 2 1 1 1 1 1 Gigabit Ethernet ports SFP ports SFP+ ports USB 2.
Hillstone SG-6000 E-Series Hardware Reference Guide DDR SDRAM Flash Memory 17 SG-6000-E6368 SG-6000-E6360 SG-6000-E6168 SG-6000-E6160 SG-6000-E5960 SG-6000-E5760 SG-6000-E5660 SG-6000-E5568 SG-6000-E5560 SG-6000-E5268 SG-6000-E5260 SG-6000-E5168 SG-6000-E3965 SG-6000-E3968 SG-6000-E3960 SG-6000-E3668 SG-6000-E3662 SG-6000-E2868 SG-6000-E2860 SG-6000-E3660 SG-6000-E2800 SG-6000-E2300 SG-6000-E1700 SG-6000-E1606 SG-6000-E1600 SG-6000-E1100 (WLAN version) SG-6000-E1100 (4G version) SG-6000-E1100 (WLAN+4G v
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E1100 (WLAN version) SG-6000-E1100 (4G version) SG-6000-E1100 (WLAN+4G version) SG-6000-E6368 SG-6000-E6360 SG-6000-E6168 SG-6000-E6160 SG-6000-E5960 SG-6000-E5760 SG-6000-E5660 SG-6000-E5568 SG-6000-E5560 SG-6000-E5268 SG-6000-E5260 SG-6000-E5168 SG-6000-E3965 Dimensions (W×D×H) Weight 18 SG-6000-E3968 SG-6000-E3960 SG-6000-E3668 SG-6000-E3662 SG-6000-E3660 SG-6000-E2868 SG-6000-E2860 SG-6000-E2800 SG-6000-E2300 SG-6000-E1700 SG-6000-E1606 SG-
Hillstone SG-6000 E-Series Hardware Reference Guide Gross weight: 16.
Hillstone SG-6000 E-Series Hardware Reference Guide Relative Humidity 10%-95% (non-condensing) Note: DDR SDRAM is the random access memory to store the communication data for the CPU. Flash Memory is used for storing the operating system firmware, configuration and application files. Ports This section introduces attributes of interfaces (ports) on the Hillstone devices, including console port, auxiliary port, USB port, gigabit copper port, SFP port， QSFP+ ports and XFP port.
Hillstone SG-6000 E-Series Hardware Reference Guide USB Port Hillstone device provides up to two USB host ports. Attributes for the USB port are shown in the following table. Table 1-23: USB Port Attributes Attribute Description Connector USB Type-A interface Port Standard USB 2.0 host interface Negotiation Mode 1.1/2.0 autosensing Gigabit Copper Port Hillstone device provides several fixed gigabit copper ports; the gigabit Combo port also supports the copper cable connection.
Hillstone SG-6000 E-Series Hardware Reference Guide SFP optical module/transceiver Copper SFP transceiver If you choose to use SFP optical module in SFP port, you should use LC-Type optical connector. Hillstone device supports five types of 1000Base-FX SFP optical modules. All optical modules are hot-swappable.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-27: SFP Copper Module Attributes Attribute Description Connector RJ-45 Port Standard Auto-MDI/MDIX (crossover cable and straightthrough cable autosensing) Maximum Transmission Distance 100m 10/100/1000Mbps autosensing (some only supports 1000Mbps) Full / half-duplex Negotiation Mode Cautions: The SFP electric modules of all platforms only support 1000Mbps.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-29: SFP+ Optical Module Attributes Description Attribute Connector Fiber Type Short-haul Medium-haul Long-haul Ultra-long Haul Multimode single-mode Single-mode Single-mode Optical Optical Optical Module Optical Module Module Module (1550nm) (1550nm) (850nm) (1310nm) LC 62.5/125μm 9/125μm 9/125μm multi-mode single-mode single-mode fiber fiber fiber 9/125μm single-mode fiber Maximum Transmission 0.
Hillstone SG-6000 E-Series Hardware Reference Guide Caution: To avoid dust falling into the QSFP+ socket, you should place a rubber dust cap (originally in the accessory box) over the QSFP+ port. Table 1-31: QSFP+ Optical Module Attributes Description Short-haul Multimode Optical Module (850nm) Ultra-long Haul Singlemode Optical Module (1550nm) MPO LC 50/125μm multi-mode fiber 9/125μm single-mode fiber Maximum Transmission Distance 0.
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-33: XFP Optical Module Attributes Description Attribute Short-haul Multimode Optical Module (850nm) Medium-haul Single-mode Optical Module (1310nm) Long-haul Single-mode Optical Module (1550nm) Ultra-long Haul Singlemode Optical Module (1550nm) Connector LC Fiber Type 50/125μm multimode fiber 9/125μm single-mode fiber 9/125μm single-mode fiber 9/125μm single-mode fiber Maximum Transmission Distance 0.3km (984.
Hillstone SG-6000 E-Series Hardware Reference Guide 1. When the device is working, press the CLR button in the pinhole and the device will restart. 2. After the device restarted, the CON port outputs the information of CLR button pressed and the STA and ALM LEDs turn to constantly red. After the LEDs turn off, the device will restart again. Expansion Slot The chassis height of SG-6000-E6368, SG-6000-E6360, SG-6000-E6168 and SG6000-E6160 is 2.
Hillstone SG-6000 E-Series Hardware Reference Guide External power adapter connects to the external AC power supply. For instructions on how to replace power supply modules, refer to Installing and Removing the Power Supply Module.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 1-23: AC Power Module Figure 1-24: DC Power Module The power LED description for is listed in the following table. Table 1-35: Power Supply Module LED Descriptions LED OK AC DC Color/Status Description Green/Always on Power module is functioning normally. Off No power input. Yellow/Always on Power module has error. Off Power module is functioning normally. Green/Always on AC power module is functioning normally.
Hillstone SG-6000 E-Series Hardware Reference Guide and SG-6000-E2868. The hard disk module mainly saves logs to the local and achieves the goals of device monitoring, behavior auditing, etc. All the platforms above support three type of storage capacity: 128G, 256G and 512G. The default storage capacity is different on different platforms.
Hillstone SG-6000 E-Series Hardware Reference Guide clearing. Besides, it is recommended that you should replace the anti-dust mesh every 3 or 6 months according to the clearness status of your equipment room. To purchase a new anti-dust mesh, contact Hillstone. SG-6000-E3968/E3960/E3960-GM/E3668/E3662/E3662-GM/SG-6000E3660/E2868/E2860/E2300/2800 has a built-in cooling system. Figure 1-25: Air Circulation The ambient temperature of the working environment should keep between 0 and 40 degree Celsius.
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 2 Installation Preparations Introduction To prevent personnel injury and equipment damage, please carefully read all the safety warnings and cautions in this chapter before the installation. Hillstone products are designed for indoor use.
Hillstone SG-6000 E-Series Hardware Reference Guide Use electromagnetic shielding when necessary. Grounding Requirements To use the device more safely: Ensure that the grounding screw of the chassis is well grounded via the grounding wire. Ensure that the grounding pin of the power plug is well grounded.
Hillstone SG-6000 E-Series Hardware Reference Guide Terminal: Configuration terminal (e.g. an ordinary PC). Tools: Philips screwdrivers and ESD wrist strap. Cables: Power cable, console cable and Ethernet cable.
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 3 Installation Before Installation A yellow seal with dark ink characters is stuck on a mounting screw of the chassis. Keep the seal intact. The sales representative will check this seal before maintenance operation. Please get the permission of your sales representative before opening the chassis yourself. Warranty will be void if you disassemble the chassis without authorization.
Hillstone SG-6000 E-Series Hardware Reference Guide Make sure the workbench is stable and well grounded. Make sure the intake and the exhaust vents are unblocked, and keep the device well ventilated. Do not place any heavy object on the top of the chassis. Installing the Device on a Rack Before mounting the device on a rack, ensure that the power is off, and the rack is stable enough and well grounded. Hillstone devices are designed for a 19-inch standard rack.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 3-3: Installing the Rack-mounting Ears (1U Chassis as example) Step 3: Two person are needed to cooperate to raise the device and place it to the tray of the rack (or two person place the device to the tray of lift first, then use the lift to achieve it). Step 4: Keep the center of the rack-mounting ear and the center of the rack hole horizontally even and tighten the screws, as shown in Figure 3-4.
Hillstone SG-6000 E-Series Hardware Reference Guide Connecting the Ground Wire To meet safety requirements, you must correctly connect the grounding screw on the chassis to the earth ground by a grounding wire. The grounding resistance should be less than 5 Figure 3-5: Connecting the Ground Wire (1U Chassis as example) Warning: The correct connection of the ground wire on the chassis is an essential safeguard against lightning shocks and interference.
Hillstone SG-6000 E-Series Hardware Reference Guide module connected by a single-mode or multi-mode cable. The XFP port uses singlemode or multi-mode cables to access Ethernet. All SFP Port and XFP Port optical modules of Hillstone products use LC-type optical connector; therefore, you should connect the optical modules using optical fiber ended with LC-type connector.
Hillstone SG-6000 E-Series Hardware Reference Guide Keep the connector of the optical cable clean. Figure 3-7: Connecting the Ethernet Fiber Cable Warning: Laser danger! To protect your eyes from radiation harm, do not stare into a cable connector connected to a laser generator. Connecting an AC Power Cable The AC power cable is shipped with the chassis. Prepare a single-phase threeterminal power socket with a ground contact in advance.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 3-8: Connecting an AC Power Cable Note: If a product does not have a power switch, you can skip Step2 and Step4. Connecting a DC Power Cable To power the device with DC power source, use DC power cables to connect the device and the external DC power source. Warning: Before performing the procedure, ensure that the cable is not connected with any power source and make sure the cables will not be powered on during the process.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 3-9: Connecting a DC Power Cable Connecting a Power Adapter To provide the power supply, connect the power adapter of the devices with the external AC power supply as follows: 1. Insert the DC output plug of the power adapter into the AC power interface at the back panel of the device. 2. Connect the power adapter to the external AC power supply.
Hillstone SG-6000 E-Series Hardware Reference Guide 1. According to the function you use, select the corresponding antenna. 2. Install the antenna to the SMA connector at the back panel of the device by rotating the antenna clockwise. Installing the SIM Card To install the SIM card for SG-6000-E1100 (4G version) or SG-6000-E1100 (WLAN+4G version), take the following steps: 1. Purchase the SIM card from the ISP and activate the data connection service. 2.
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 4 Boot and Configuration Introduction This chapter describes the initial system boot and basic configuration of Hillstone SG-6000 series, using a PC as the console terminal. Establishing a Configuration Environment Hillstone devices support both local and remote configuration. Administrators can use the following configuration methods.
Hillstone SG-6000 E-Series Hardware Reference Guide terminal session to 9600bps, 8 data bits, 1 stop bit, none parity, and none flow control, as shown in Figure 4-2: Figure 4-2: Setting Parameters for the Terminal Session 3. Switch on the power supply, and the device performs self-test and initializes the configuration automatically. If the booting succeeds, the system will display the command line prompt “login”.
Hillstone SG-6000 E-Series Hardware Reference Guide 3. Enter the default administrator name and password “hillstone” in both the Login and Password text boxes. 4. Click the Login button to enter WebUI main page. Then you can set other configurations to the device. Tenet and SSH You can also establish Telnet and SSH configuration environments. For more information, please see StoneOS User Manual.
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 5 Hardware Maintenance and Replacement Introduction This chapter explains how to install and remove the power supply module, the expansion module and the fan tray.
Hillstone SG-6000 E-Series Hardware Reference Guide Installing and Removing the Expansion Module SG-6000-E6368, SG-6000-E6360, SG-6000-E6168, SG-6000-E6160, SG-6000E5960, SG-6000-E5760, SG-6000-E5660, SG-6000-E5568, SG-6000-E5560, SG6000-E5268, SG-6000-E5260, SG-6000-E5168, SG-6000-E3965, SG-6000-E3968, SG-6000-E3960, SG-6000-E3668, SG-6000-E3662, SG-6000-E3660, SG-6000E2868 and SG-6000-E2860 can accommodate expansion modules. This section describes how to install and remove the expansion module.
Hillstone SG-6000 E-Series Hardware Reference Guide 2. Pull the fan tray out of the chassis by holding the provided handle. Note: To avoid over-heating, insert a replacement fan tray immediately after removing the existing one. Installing and Removing the Anti-dust Mesh SG-6000-E6368, SG-6000-E6360, SG-6000-E6168, SG-6000-E6160, SG-6000E5568, SG-6000-E5560, SG-6000-E5268, SG-6000-E5260, SG-6000-E5168 and SG-6000-E3965 are designed with anti-dust mesh.
Hillstone SG-6000 E-Series Hardware Reference Guide Installing and Removing the Hard Disk Module SG-6000-E6368, SG-6000-E6168, SG-6000-E5568, SG-6000-E5268, SG-6000E5168, SG-6000-E3968, SG-6000-E3668, and SG-6000-E2868 are designed with the hard disk module. Take the following steps to install the hard disk module: 1. Make sure the device is not powered and you have worn antistatic gloves. 2.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 5-4: Placing the Hard Disk Module 5. Use the screw in the hard disk module package to fix the hard disk module. Figure 5-5: Fixing the Hard Disk Module 6. Use a screwdriver to re-install the blank panel into the hard disk slot.
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 5-6: Installing the Blank Panel Take the following steps to remove the hard disk module: 1. Make sure the device is not powered and you have worn antistatic gloves. 2. The hard disk module is at the bottom of the device, you should turn over the device to make sure the hard disk module is visible. In order to avoid the top of the device being scratched, make sure the workbench is stable and clean. 3.
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 6 Troubleshooting Introduction This chapter provides solutions to some common problems of Hillstone devices. Losing the Administrator Password If you lose the administrator password, please contact your local sales representative. Troubleshooting Power System Check the PWR LED on the front panel of the device. If the power supply is functioning normally, the PWR LED lights steadily in green color.
Hillstone SG-6000 E-Series Hardware Reference Guide Appendix: Supported Versions of Devices During the production process, components of part SG-6000 E series devices have been updated, which may cause the incompatibility among software versions. The tables below display the devices of which the components have updated. Check whether your device is in the following tables.
Hillstone SG-6000 E-Series Hardware Reference Guide Device Model (Part of devices are delisted) Device SN Range(Update devices to the supported versions if SN is within the range) Device Supported Versions SG-6000-E3660, SG-6000E3660S, SG-6000-E2860, SG6000-E3662, SG-6000-E2868, SG-6000-E3668, SG-6000E1100, SG-6000-E1600, SG6000-E1700, SG-6000-E1606, SG-6000-E2300, SG-6000E2300S, SG-6000-E2800 SG-6000-ABG1000, SG-6000ABG2000 SG-6000-C4100, SG-6000C4550, SG-6000-C5050, SG6000-C1200W, SG-6000-C600, SG-600
Hillstone SG-6000 E-Series Hardware Reference Guide Device Model Device SN Range(Update devices to the supported versions if SN is within the range) Whether IOC2SFP+- Device Supported Versions lite is Used 5.5R2P14 and later P versions 5.5R4P9 and later P versions Before xxxxx0717xxxxxxx Yes (Before the 7th week of 2017) 5.5R5P7 and later P versions 5.5R6P2 and later P versions 5.5R7 and later versions 5.5R2P14 and later P versions 5.
Hillstone SG-6000 E-Series Hardware Reference Guide Device Model Device SN Range(Update devices to the supported versions if SN is within the range) Whether IOC2SFP+- Device Supported Versions lite is Used 5.5R6P2 and later P versions 5.5R7 and later versions 5.0R4P14 and later P versions 5.0R4P5.42 and later P versions No 5.5R1P13 and later P versions 5.5R2P2 and later P versions 5.5R3 and later versions (e.g. 5.5R4, 5.5R5, 5.5R6, 5.
Hillstone SG-6000 E-Series Hardware Reference Guide Addendum FCC Statement Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC Statement: This device complies with Part 15 of the FCC Rules.
Hillstone SG-6000 E-Series Hardware Reference Guide This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may not be co-located with any other transmitter or antenna. 2.4GHz Band List: DTS (2400-2483.
Hillstone SG-6000 E-Series Hardware Reference Guide relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC) and R&TTE (1999/5/EC). The equipment passed the test which was performed according to the following European standards: •ETSI EN 300 328 V1.8.1 (2012-06) •EN 301 893 V1.7.1 (2012-06) •EN 62311: 2008 •EN 301 908-1 V5.2.1 EN 301 908-2 V5.2.1 EN 301 511 V9.0.2 •EN 300 440-1 V1.6.1 EN 300 440-2 V1.4.1 •EN 301 489-1 V1.9.2 EN 301 489-7 V1.3.1 EN 301 489-17 V2.2.
Hillstone SG-6000 E-Series Hardware Reference Guide Copyright Information Copyright © 2020 Hillstone Networks. All rights reserved. Hillstone, Hillstone Networks logo, StoneOS, StoneManager, Hillstone PnPVPN, UTM Plus are trademarks of Hillstone Networks. All other trademarks or registered marks are the property of their respective owners. Hillstone Networks assumes no responsibility for any inaccuracies in this document.
