DRAFT 26-FEB-2019 WatchCare™ Incontinence Management System User and Service Manual Product No.
DRAFT 26-FEB-2019
DRAFT 26-FEB-2019 REVISION © 2019 by Hill-Rom Services, Inc. ALL RIGHTS RESERVED. Distributed by: HILL-ROM, INC. 1069 STATE ROUTE 46 E BATESVILLE, IN 47006-9167 USA 800-445-3720 Manufactured by: HILL-ROM, INC. 1069 STATE ROUTE 46 E BATESVILLE, IN 47006-9167 USA No part of this text shall be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information or retrieval system without written permission from Hill-Rom Services, Inc.
DRAFT 26-FEB-2019 First Printing, 2018 Bluetooth® is a registered trademark of Bluetooth Sig, Inc. Clorox HealthCare® is a registered trademark of Clorox Professional Products Company, Inc. OxyCide® is a registered trademark of Ecolab USA Inc. Torx® is a registered trademark of Acument Intellectual Properties, LLC. Virex® is a registered trademark of Diversey, Inc. Wex-Cide™ is a trademark of Wexford Labs, Inc. Quick View™, StayInPlace™, and WatchCare™ are trademarks of Hill-Rom Services, Inc.
DRAFT 26-FEB-2019 Table of Contents Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Document Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRAFT 26-FEB-2019 Table of Contents Foot-End Cover With Holes . . . . . . . . . . . . . . . . . . . . . . . . . Foot-End Cover without Holes . . . . . . . . . . . . . . . . . . . . . . Final Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antenna Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . Graphic Replacement for the Head, Seat, and Thigh Sections, and Deck Filler—Progressa® Bed. . . . . . . . . . . . . . . . . . . . . . . .
DRAFT 26-FEB-2019 Intended Use INTENDED USE The Incontinence Monitor is intended to detect and provide a timely alert when the patient’s skin is exposed to incontinence (both urine and liquid fecal events). INTRODUCTION The WatchCare™ Incontinence Management System (system) provides a discreet visual alert and optional equipment call alerts after moisture is detected on the WatchCare™ smart pad.
DRAFT 26-FEB-2019 Symbols SYMBOLS DOCUMENT SYMBOLS This manual contains different typefaces and symbols to make the content easier to read and understand: • Standard text—used for regular data. • Boldface text—emphasizes a word or phrase. • NOTE:—sets apart special data or important instruction clarification. • WARNING or CAUTION – – A WARNING identifies situations or actions that may have an effect on patient or user safety. To ignore a warning could cause patient or user injury.
DRAFT 26-FEB-2019 Symbols Symbol Description Identifies these WatchCare™ System components (Progressa® and VersaCare® Beds): • WatchCare™ 1/4" communication cable • Facility equipment call jack designated for the WatchCare™ 1/4"communication cable • WatchCare™ connector on the bed Manufacturer Model or type reference Serial number Manufacture date ATTENTION: Consult accompanying documents Federal Communications Commission Degree of protection against Ingress of Water Type B applied part according t
DRAFT 26-FEB-2019 Safety Instructions Symbol Description Do not dispose as Unsorted Municipal Waste SAFETY INSTRUCTIONS WARNING: Obey these safety instructions to help prevent injury and/or equipment damage: • Warning—Read and understand all warnings in this manual and on the unit itself prior to use with a patient. • Warning—The potential for electrical shock exists with electrical equipment. Failure to follow facility protocols may cause death or serious injury.
DRAFT 26-FEB-2019 Safety Instructions • Warning—To safely stop the operation of the system, unplug the bed and/or the external power supply from the power outlet. FCC GUIDANCE Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by Hill-Rom might cause harmful interference and void the FCC authorization to operate this product. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
DRAFT 26-FEB-2019 Quick View™ List of Features QUICK VIEW™ LIST OF FEATURES PROGRESSA® AND VERSACARE® BEDS Item Feature A WatchCare™ smart pad B WatchCare™ antennas C WatchCare™ reader D WatchCare™ indicator light E (not WatchCare™ connector shown) (on the bed) and WatchCare™ 1/4" communication cable CENTRELLA® SMART+ BED Item Feature A WatchCare™ smart pad B WatchCare™ antennas C (not WatchCare™ reader shown) D SafeView®+ Alerts— WatchCare™ indicator light E (not Nurse call system con
DRAFT 26-FEB-2019 Quick View™ List of Features Item Description B WatchCare™ Antennas There are four WatchCare™ antennas (antenna(s)) located under the mattress. They identify that a smart pad is present and send a signal to the WatchCare™ reader. C WatchCare™ Reader The WatchCare™ RFID reader (reader) is located on the left side of the bed near the seat section. The RFID reader sends a signal prompting the WatchCare™ indicator light as to the smart pad’s status.
DRAFT 26-FEB-2019 Quick View™ List of Features Item E Description Centrella® Bed with a different nurse call system— a. Connect the two-cable end of the WatchCare™ adapter to the bed. b. c. Connect the 37-pin end of the adapter cable to the facility’s communication cable. Connect the remaining end (the 1/4" cable connector) of the adapter cable to the facility’s equipment call jack designated for the WatchCare™ System.
DRAFT 26-FEB-2019 Prepare the System for Use PREPARE THE SYSTEM FOR USE WARNING: To help prevent injury and/or equipment damage, obey these warnings: • Warning—Keep cables out of the patient foot fall area. • Warning—Connect the WatchCare™ 1/4" communication cable or WatchCare™ adapter cable (as applicable) to an equipment call jack designated for the WatchCare™ System only. Patient injury could occur if the nurse call system is not operational. 1.
DRAFT 26-FEB-2019 Prepare the System for Use Centrella® Bed P7900A0, P7900B0 • Centrella® Bed P7900B1 and Newer Facility Connection Progressa® and VersaCare® Beds—the WatchCare™ 1/4"communication cable is connected to the WatchCare™ connector on the bed and to the facility’s equipment call jack designated for the WatchCare™ System’s incontinence alerts.
DRAFT 26-FEB-2019 Prepare the System for Use 3. Put a smart pad(s) in the middle of the bed with the head icon toward the head end of the bed and foot icon toward the foot end. smart pad Placement 4. Listen for a single beep, and make sure the indicator light has turned green. These let you know that the pad has been detected and the incontinence monitoring has begun. NOTES: • Store unused, clean smart pads at least 2 feet (61 cm) from the bed.
DRAFT 26-FEB-2019 Transport The Bed Replace the WatchCare™ smart pad The indicator light will flash amber to indicate an incontinence event. If you are using a nurse call system, customizable incontinence alerts can be sent to— • The nurse call console • The nurse call dome light over the door, outside the patient’s room • The applicable mobile devices available at your facility • The nurse call status board 1.
DRAFT 26-FEB-2019 Cleaning and Disinfecting CLEANING AND DISINFECTING NOTE: This section does not apply to the smart pads. The smart pads are intended for single use only. Discard a soiled smart pad at least 2 feet (61 cm) from the bed so that the reader no longer detects the soiled pad. WARNING: To help prevent injury and/or equipment damage, obey these warnings: • Warning—The potential for electrical shock exists with electrical equipment.
DRAFT 26-FEB-2019 Cleaning and Disinfecting CAUTION: To help prevent equipment damage, obey these cautions: • • • Caution—Do not steam clean or power wash the system. Pressure and excessive moisture can damage the protective surfaces of the system and its electrical components. Caution—Do not use harsh cleansers/detergents, heavy duty grease removers, solvents such as toluene, xylene, or acetone, and do not use scouring pads (you may use a soft bristle brush).
DRAFT 26-FEB-2019 Cleaning and Disinfecting Table 1 below summarizes the approved cleaners/disinfectants for use with the associated contact time for disinfection. Table 1: Approved Cleaners/Disinfectants Recommended Recommended for Disinfection for Routine against Cleaning and Clostridium Disinfection Difficile (C.
DRAFT 26-FEB-2019 Cleaning and Disinfecting b. Adjust the mattress position as necessary to get access to the antennas. Refer to the bed’s service manual. STEP 1: Cleaning a. As necessary, first remove visible soil from the reader, indicator light, and antennas using a wiping cloth soaked with an approved cleaner/disinfectant (see “Table 1: Approved Cleaners/Disinfectants” on page 15). • A soft bristle brush may be used to loosen hardened soil. • Use as many wiping cloths as needed to remove the soil.
DRAFT 26-FEB-2019 Preventive Maintenance STEP 2: Disinfection a. b. With a new or clean wiping cloth soaked in an approved cleaner/disinfectant, use light pressure to wipe all exterior surfaces of the reader, indicator light, and antennas. Make sure all surfaces remain wet with the cleaner/disinfectant for the specified contact time. Re-wet surfaces with a new wiping cloth as necessary. See “Table 1: Approved Cleaners/Disinfectants” on page 15 for the contact time.
DRAFT 26-FEB-2019 Troubleshooting TROUBLESHOOTING WARNING: Warning—Only facility-authorized persons should service the system. Service by unauthorized persons could cause injury or equipment damage. If the trouble shooting information below does not correct the problem, contact Hill-Rom. NOTES: • Do step 1 of the Solution first, and then if necessary, do step 2, and so on until you have fixed the problem.
DRAFT 26-FEB-2019 Troubleshooting Problem Solution Progressa® and Caregiver VersaCare® Beds— 1. Unplug the bed, and then plug the bed in to the indicator light is power to reset the bed. off even though the 2. Contact your facility-authorized service LEDs on the reader persons. flash at power up. Service Person Only 1. Make sure the indicator light is not damaged. 2. Make sure the indicator light cable is not damaged and it is fully connected to the reader and the indicator light P.C. board. 3.
DRAFT 26-FEB-2019 Troubleshooting Problem Solution All beds—an equipment alert was not sent for an incontinence event. Caregiver 1. Make sure the cable that connects the bed to the equipment call jack (WatchCare™ 1/4" communication cable, SideCom® cable, or WatchCare™ adapter cable) is not damaged and it is fully connected to the equipment call jack and the bed. Replace the cable as necessary. 2. Unplug the bed, and then plug the bed in to power to reset the bed. 3.
DRAFT 26-FEB-2019 Replacement Parts REPLACEMENT PARTS EXPENDABLE PARTS Item P/N Description P006980 Smart pad Qty Page As required 12 SERVICE PARTS For replacement service parts for the Centrella® Smart+ Bed, see the bed’s service manual (193588). WARNING: Only facility-authorized persons should service the system. Service by unauthorized persons could cause injury or equipment damage.
DRAFT 26-FEB-2019 Replacement Parts Item P/N Description Qty Page 20863305 Antenna assembly, 705 mm (yellow indicator; includes gasket), Progressa® Bed 2 42 20863401 Reader with gasket and antenna tape, VersaCare® Bed 1 27 20863403 Reader with gasket and antenna tape, Progressa® Bed 1 27 201009S Indicator light with cable assembly 1 34 199673 Reader gasket 1 27 197328 Screw, reader housing 6 27 208680S Assembly, equipment call cable 1 48 208506S Assembly, WatchCare™ 1/4" equi
DRAFT 26-FEB-2019 Replacement Parts Item P/N Description Qty Page 201582 Power cable, VersaCare® Bed (A - J models) 1 29 198184 Power cable, VersaCare® (K 1 and newer models) and Progressa® Beds 29 199672 Antenna gasket 1 42 208635 Antenna tape As 42 required 199273 Screw, lens cover 2 34 199674 Indicator light adhesive 1 34 206911 Graphic, head section, Progressa® Bed 1 45 206912 Graphic, seat section, Progressa® Bed 1 45 WatchCare™ Incontinence Management System User an
DRAFT 26-FEB-2019 Replacement Parts Item P/N Description Qty Page 206913 Graphic, thigh section, Progressa® Bed 1 45 206914 Graphic, deck filler, Progressa® Bed 1 45 198343 Indicator light label 1 52 207837 Branding label, equipment call cable 1 52 207838 Branding label, equipment call jack 1 52 207839 Branding label, bed plug (equipment call connector) 1 52 207606 Branding label, VersaCare® 2 Bed 52 207840 Branding label, Progressa® Bed 52 2 WatchCare™ Incontinence Mana
DRAFT 26-FEB-2019 Service Part Replacement Procedures Item P/N Description Qty Page 19124 Cable tie As required 64565 Cable tie mount As required 209378 Prop 65 label 1 52 SERVICE PART REPLACEMENT PROCEDURES For replacement procedures for the Centrella® Smart+ Bed, see the bed’s service manual (193588).
DRAFT 26-FEB-2019 Service Part Replacement Procedures 1. toxic to skin, eyes, and respiratory tract. Do not use the cleaner near an open flame or in confined areas. • Warning—Recycle or discard no longer used parts in accordance with local regulations. Make sure the brake is set. 2. Remove the sleep surface. Refer to the bed’s service manual. 3. Raise the bed to its highest position. 4. Raise the siderails.
DRAFT 26-FEB-2019 Service Part Replacement Procedures 1.1 Reader Replacement 1. Make sure the bed is unplugged and you have done the steps for “Setup” on page 25. 2. Near the reader, remove the cable tie(s) that holds the power cable with the other cables on the bed. 3. Remove the heat shrinks from the antenna cable connections. 4. Disconnect the antenna-reader cables from the antenna cables. 5. Remove the reader from the bed. VersaCare® Bed 6.
DRAFT 26-FEB-2019 1.1 Reader Replacement 9. Disconnect all cables except the ANT 1 reader cable from the P.C. board. 10. If the back cover is installed on the new reader, remove the cover. 11. Remove the P.C. board from the new reader. 12. Connect the cables to the new P.C. board (the connectors on the P.C. board are specific to the cables): • J1— Power • J15—Indicator light cable • J17—Equipment Call connector o 13. Install the new P.C. board in the new reader.
DRAFT 26-FEB-2019 1.1 Reader Replacement 14. Install the back cover on to the reader. Make sure the gasket inserts are correctly aligned. 15. Install the six screws to attach the back cover to the reader. 16. Remove any tape residue from the back cover of the reader. 17. Use the alcohol-based cleaner to clean the back cover of the reader and the area where the reader was installed on the bed. Let the back cover and area dry. 18.
DRAFT 26-FEB-2019 1.2 Power Cable Replacement 1.2 Power Cable Replacement 1. Make sure the bed is unplugged and you have done the steps for “Setup” on page 25. 2. Get access to the Logic Control P.C. board (VersaCare® Bed, A through J model bed) or upper control board (UCB) (VersaCare® Bed, K or newer model bed or Progressa® Bed). Refer to the bed’s service manual. 3. Make a note of the power cable connections on the Logic Control P.C.
DRAFT 26-FEB-2019 1.2 Power Cable Replacement 7. Remove the reader from the bed. 8. Remove the six screws that attach the back cover to the reader. CAUTION: Caution—Failure to wear an antistatic strap could cause equipment damage. 9. Put on the antistatic strap. 10. Remove the P.C. board from the reader. 11. Disconnect the power cable from J1 on the P.C. board, and remove the old power cable from the bed. 12. Connect the new power cable to J1 on the P.C. board.
DRAFT 26-FEB-2019 1.2 Power Cable Replacement 13. Install the P.C. board in the reader. WARNING: Warning—Failure to correctly align the gaskets on the covers of the reader could permit fluids to get into the enclosure. Injury or equipment damage could occur. 14. Install the back cover on to the reader. Make sure the gasket inserts are correctly aligned. 15. Install the six screws to attach the back cover to the reader. 16. Remove any tape residue from the back cover of the reader. 17.
DRAFT 26-FEB-2019 1.2 Power Cable Replacement 22. Do as applicable for your bed: VersaCare® Bed a. Install the cable channel cover. b. Install the cover for the Logic Control P.C. board (VersaCare® Bed A through J model) or the UCB (VersaCare® Bed K or newer model). Refer to the bed’s service manual. Progressa® Bed a. Put the hose cover in position on the bed, and install the screw to attach the hose cover to the bed. b. Install the cover for the UCB. Refer to the bed’s service manual. 23.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement 1.3 Indicator Light Assembly Replacement 1. Make sure the bed is unplugged and you have done the steps for “Setup” on page 25. 2. Raise the knee section to its highest position. 3. At the indicator light assembly, cut the light assembly cable to free it from the light assembly. 4. Remove the indicator light assembly from the bed. 5.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement VersaCare® Bed CAUTION: Caution—The foot section of the bed must be extended for the cable routing. Otherwise, equipment damage could occur. 1. Extend the foot section. 2. Follow the routing of the old light assembly cable to the reader, and then use the same routing for the new light assembly cable. Remove and install cable ties as necessary.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement Foot-End Cover With Holes 1. Remove the four screws (A) that attach the foot-end cover (B) to the bed (see the image below). 2. Remove the foot-end cover (B) from the bed. 3. Follow the routing of the old light assembly cable to the reader, and then use the same routing for the new light assembly cable. Remove and install cable ties as necessary.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement • At the head end of the guide tube, you may need to use a screwdriver to move the plastic cover enough to get access to the old and new cables. • After you route the new cable through the guide tube, do these: a. Pull the old cable out from the guide tube. CAUTION: Caution—The foot section must be extended to correctly install the indicator light. Otherwise, equipment damage could occur. b. Extend the foot section. c.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement 2. Follow the routing of the old light assembly cable to the reader, and then use the same routing for the new light assembly cable. Remove and install cable ties as necessary. NOTE: At the head end of the guide tube, you may need to use a screwdriver to move the plastic cover enough to get access to the old and new cables. • After you route the new cable through the guide tube, do these: a. Pull the old cable out from the guide tube.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement 3. Go to “Final Steps” on page 39. Final Steps 1. Near the reader, remove the cable tie(s) that holds the light assembly cable with the other cables on the bed. 2. Remove the reader from the bed. 3. Remove the six screws that attach the back cover to the reader. CAUTION: Caution—Failure to wear an antistatic strap could cause equipment damage. 4. Put on the antistatic strap. 5. Remove the P.C. board from the reader. 6.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement 8. Install the P.C. board in the reader. WARNING: Warning—Failure to correctly align the gaskets on the covers of the reader could permit fluids to get into the enclosure. Injury or equipment damage could occur. 9. Install the back cover on to the reader. Make sure the gasket inserts are correctly aligned. 10. Install the six screws to attach the back cover to the reader. 11. Remove any tape residue from the back cover of the reader. 12.
DRAFT 26-FEB-2019 1.3 Indicator Light Assembly Replacement 15. The replacement is complete. Do the function checks on page 53 and in the bed’s service manual. As you operate the bed’s articulation functions, make sure the cables are not in a location where they could get damaged or pinched.
DRAFT 26-FEB-2019 1.4 Antenna Assembly Replacement 1.4 Antenna Assembly Replacement 1. Make sure the bed is unplugged and you have done the steps for “Setup” on page 25. 2. Make a note of these: • • • The antenna’s location The antenna’s orientation The indicator color on the antenna’s cable. NOTES: • The antenna cable lengths are different. The indicator color on the cable will help to make sure the new antenna is correct for its location.
DRAFT 26-FEB-2019 1.4 Antenna Assembly Replacement CAUTION: Caution—Make sure to install the new antenna in the correct orientation and location. Otherwise, the antenna may not operate as intended. 5. Remove the adhesive covering from the gasket on the bottom of the new antenna, and then install the antenna in the correct orientation and location on the sleep deck. Firmly press the antenna into position for 10 seconds with approximately 75 lb (34 kg) of force. 6.
DRAFT 26-FEB-2019 1.4 Antenna Assembly Replacement 11. Connect the antenna cable to the antenna-reader cable. 12. Put insulated tape over the cable connection. 13. At the cable tie mount(s) near the reader, install a cable tie(s) to hold the cables on to the bed. 14. The replacement is complete. Do the function checks on page 53 and in the bed’s service manual. As you operate the bed’s articulation functions, make sure the cables are not in a location where they could get damaged or pinched.
DRAFT 26-FEB-2019 1.5 Graphic Replacement for the Head, Seat, and Thigh Sections, and Deck Filler— 1.5 Graphic Replacement for the Head, Seat, and Thigh Sections, and Deck Filler—Progressa® Bed 1. Make sure the bed is unplugged and you have done the steps for “Setup” on page 25. 2. Head, seat, or thigh section graphic—remove the antenna(s) from the applicable graphic. 3. Remove the graphic from the sleep deck. 4. Use the alcohol-based cleaner to clean the area where the graphic was removed.
DRAFT 26-FEB-2019 1.5 Graphic Replacement for the Head, Seat, and Thigh Sections, and Deck Filler— CAUTION: Caution—Make sure to install the new graphic in the correct orientation and location. Otherwise, the antennas may not operate as intended. 5. 6. Remove the adhesive covering from the bottom of the graphic, and then install the graphic in the correct orientation and location on the sleep deck. Head, seat, or thigh section graphic—do as follows: a. b. c. d.
DRAFT 26-FEB-2019 1.5 Graphic Replacement for the Head, Seat, and Thigh Sections, and Deck Filler— e. 7. Remove the other adhesive covering from the new antenna gasket. Make sure the antenna is in the correct orientation and location on the graphic. Then, firmly press the antenna into position for 10 seconds with approximately 75 lb (34 kg) of force. The replacement is complete. Do the function checks on page 53 and in the bed’s service manual.
DRAFT 26-FEB-2019 1.6 Equipment Call Cable Replacement 1.6 Equipment Call Cable Replacement 1. Make sure the bed is unplugged and you have done the steps for “Setup” on page 25. 2. Disconnect the WatchCare™ 1/4" communication cable from the equipment call jack and from the bed. 3. Remove the equipment call cable connector from the bed. VersaCare® Bed 4. Progressa® Bed Use the alcohol-based cleaner to clean the area where the equipment call cable connector was removed. Let the area dry.
DRAFT 26-FEB-2019 1.6 Equipment Call Cable Replacement b. At the location where the old connector was removed, put the new connector into position. – Progressa® Bed—make sure the connector is aligned with the head-end edge of the UCB box and the connector’s patient-left side is aligned with the patient-left side of the UCB box (box without holes) or aligned with the hole in the box. UCB box without holes – c.
DRAFT 26-FEB-2019 1.6 Equipment Call Cable Replacement 9. Remove the six screws that attach the back cover to the reader. CAUTION: Caution—Failure to wear an antistatic strap could cause equipment damage. 10. Put on the antistatic strap. 11. Remove the P.C. board from the reader. 12. Disconnect the old equipment call cable from J17 on the P.C. board, and remove the cable from the bed. 13. Connect the new equipment call cable to J17 on the P.C. board. 14. Install the P.C. board in the reader.
DRAFT 26-FEB-2019 1.6 Equipment Call Cable Replacement WARNING: Warning—Failure to correctly align the gaskets on the covers of the reader could permit fluids to get into the enclosure. Injury or equipment damage could occur. 15. Install the back cover on to the reader. Make sure the gasket inserts are correctly aligned. 16. Install the six screws to attach the back cover to the reader. 17. Remove any tape residue from the back cover of the reader. 18.
DRAFT 26-FEB-2019 1.7 Label Replacement 1.7 Label Replacement NOTE: Replace a label if it can not be read or if it is not fully bonded to its location. 1. Remove the label. CAUTION: Caution—Failure to clean the label location thoroughly could prevent the label from bonding correctly. 2. Use the alcohol-based cleaner to clean the area where the label was removed. Let the area dry. 3. Install the new label where the old label was removed. Make sure the label has fully bonded to its location.
DRAFT 26-FEB-2019 1.8 WatchCare™ System Function Check 1.8 WatchCare™ System Function Check 1. Make sure any WatchCare™ smart pads are at least 2 feet (61 cm) from the bed, and then plug the bed in. 2. At the indicator light, make sure the white light comes on solid. This could take up to 2 minutes. If the white light does not come on, check the cable connections. (For more information about the indicator light, see “Indicator Light—Visual Identification” on page 8.) 3.
DRAFT 26-FEB-2019 1.8 WatchCare™ System Function Check SPECIFICATIONS Product Identification Product Number Description P006979 WatchCare™ reader, indicator light, and antennas P006980 WatchCare™ smart pad Dimensions Feature Dimension WatchCare™ smart pad 30” x 36” (76.2 cm x 91.
DRAFT 26-FEB-2019 1.8 WatchCare™ System Function Check AC/Mains Power Requirements Condition Range Integrated System Rated voltage 24 to 55 V DC Rated current 0.5 A a Non-Integrated System (not available at this time) Rated voltage 24 to 55 V DC Rated current 0.5 A a. The non-integrated system uses an XP Power AFM45US24 external power supply that is semi-permanently attached to the bed.
DRAFT 26-FEB-2019 Specifications ELECTROMAGNETIC EMISSIONS GUIDANCE CAUTION: To help prevent equipment damage, obey these cautions: • • • Caution—This device meets all requirements for electromagnetic compatibility per IEC 60601-1-2. It is unlikely that the user will encounter problems with this device because of inadequate electromagnetic immunity. However, electromagnetic immunity is always relative, and standards are based on anticipated environments of use.
DRAFT 26-FEB-2019 Specifications into service according to the EMC information supplied in the tables that follow. Guidance and Manufacturer's Declaration—Electromagnetic Emissions The P006979 is intended for use in the electromagnetic environment specified below. The customer or the user of the model P006979 should make sure it is used in such an environment.
DRAFT 26-FEB-2019 Specifications Guidance and Manufacturer's Declaration - Electromagnetic Immunity The P006979 is intended for use in the electromagnetic environment specified below. The customer or the user of the P006979 should make sure it is used in such an environment.
DRAFT 26-FEB-2019 Specifications Guidance and Manufacturer's Declaration - Electromagnetic Immunity The P006979 is intended for use in the electromagnetic environment specified below. The customer or the user of the P006979 should make sure it is used in such an environment. Immunity Test IEC 60601-12 Test Level Compliance Level Conducted RF IEC 610004-6 3V 0.15 MHz - 80 MHz 6 V in ISM bands between 0.15 MHz and 80 MHz 80% AM at 1 kHz 3V 0.15 MHz 80 MHz 6 V in ISM bands between 0.
DRAFT 26-FEB-2019 Specifications a. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered.
DRAFT 26-FEB-2019 Specifications Encryption Options • Off • On • Auto • PSK • WPA-TKIP • WPA2-PSK • WPA2-AES • CCKM-TKIP • CCKM-AES • WPA-PSK-AES • WPA-AES Extensible Authentication Protocol Types (EAP Types) • • • • • • • EAP-FAST PEAP-MACHAPv2 EAP-TLS PEAP-TLS EAP-TTLS LEAP PEAP-GTC Regulatory Information WARNING: Warning—Changes and/or modifications not expressly approved by HillRom, Inc. could void the user’s authority to operate the equipment. Patient safety could be compromised.
DRAFT 26-FEB-2019 Specifications USA—FEDERAL COMMUNICATIONS COMMISSION (FCC) RADIATION EXPOSURE STATEMENT CAUTION: Caution—The radiated output power of the WatchCare™ reader is far below the FCC radio frequency exposure limits. Nevertheless, the WatchCare™ reader must be used in such a manner that the potential for human contact during normal operation is minimized.
DRAFT 26-FEB-2019 Specifications will violate FCC Part 15 regulations. Modifications not expressly approved by Hill-Rom could void your authority to operate the equipment. NOTE: The WatchCare™ reader must not be co-located or operated in conjunction with any other antenna or transmitter. Wireless System Characteristics Characteristic Description Frequency Band—2.4 GHz FCC: 2.4 GHz to 2.483 GHzETSI: 2.4 GHz to 2.483 GHzMIC: 2.4 GHz to 2.495 GHzKC: 2.4 GHz to 2.483 GHz Frequency Band—5 GHz FCC: 5.
DRAFT 26-FEB-2019 Specifications Characteristic Transmit Power Settings Description 802.11a: 6 Mbps 15 dBm54 Mbps 13 dBm (PER - 10%)802.11b: 1 Mbps 16 dBm11 Mbps 16 dBm (PER 10%)802.11g: 6 Mbps 16 dBm54 Mbps 14 dBm (PER - 10%)802.11n (2.4 GHz): MCS0 Mbps 16 dBmMCS7 Mbps 12 dBm80211n (5 GHz): MCS0 Mbps 15 dBmMCS7 Mbps 12 dBmBluetooth 2 dBm (1.
DRAFT 26-FEB-2019 Specifications Immunity to Proximity Fields from Radio Frequency Wireless Communications Equipment In addition to the Radiated RF IEC 61000-4-3 as shown in the table above, the P006979 has been tested as specified in the table below. Test Frequency (MHz) Band (MHz) Service Modulation 2450 2400-2570 Bluetooth, WLAN, 802.11 b/g/n, RFID 2450, LTE Band 7 5240 5100–5800 WLAN 802.
DRAFT 26-FEB-2019 Limited Warranty LIMITED WARRANTY HILL-ROM COMPANY, INC. LIMITED WARRANTY Hill-Rom Company, Inc. (Hill-Rom) has a long tradition of providing superior products and service to our customers. Our goal is “Total Customer Satisfaction”. In that spirit, Hill-Rom is proud to offer the following warranty.
DRAFT 26-FEB-2019 Limited Warranty OUT OF WARRANTY EXCHANGE POLICY After the expiration of the original warranty, upon request, Hill-Rom will ship as a replacement, components such as selected: motors and printed circuit boards, for like units returned to Hill-Rom by the original purchaser at a substantial savings. Please call Hill-Rom Technical Support Department for current pricing.
DRAFT 26-FEB-2019 Limited Warranty NOTES: WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2) 68