User's Manual

ManualsBrandsHIKVISON ManualsElectronicsFace Recognition Terminal

Face Recognition Terminal

Quick Start Guide

UDB

GroundBottom Cover

Bracket

Bottom Screw

M6×65 Expension Bolt

Before you start: Make sure the ground surface has drilled

holes for device installation.

Steps:

1. Remove the two bottom screws (2-SC-KM3×5B-JMF) on

both sides of the bottom cover. And remove the bottom

cover.

2. Align the device with the drilled holes on the ground and

insert 3 supplied expension bolts (M6×65). Make sure the

expension bolts are higher than the ground.

3. Secure the expension bolts with nuts。

4. Install the bottom cover back on the device with 2 bottom

screws.

The actual device

appearance varies

according to

different models.

The device should be installed on the concrete surface or other

non-flammable surfaces.

The device supports plug & play. You can put the device on the

ground and start operation after powering on.

Installation

The ﬁgures are for reference only.

The Wiegand terminal here is a Wiegand input terminal. You should set

the device’s Wiegand direction to “Input”. If you should connect to

an access controller, you should set the Wiegand direction to “Output”.

For details, see the user manual.

The power supply should be 12 VDC/3 A, 36 W.

IN2

Yellow/Orange

Yellow/Blue

Yellow/Purple

Purple

Grey

Orange

Brown

White

Green

Yellow/Brown

Power

Yellow/Red

(NC)

(NO)

Yellow/Black

Alarm Input Device

Alarm Output Device

WG_OK

WG_ERR

BUZZER

12 V

Power Supply

Wiegand

Card Reader

Wiegand

Alarm Input

Alarm Output

Tag 2

Tag 4

Tag 2Tag 4

RS-485

Network Interface

Debugging Port

(For Debuggin Only)

Door Lock Interface

Wiegand

Alarm Input/Output

Power Input

USB Interface 2

USB Interface 1

Device

The wiring diagram of tag 2 and 4 on the left is shown below:

This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its

aﬃliates (hereinaer referred to as “Hikvision”), and it cannot be reproduced, changed,

translated, or distributed, parally or wholly, by any means, without the prior wrien

permission of Hikvision. Unless otherwise expressly stated herein, Hikvision does not

make any warranes, guarantees or representaons, express or implied, regarding to the

Manual, any informaon contained herein.

About this Manual

The Manual includes instrucons for using and managing the Product. Pictures, charts,

images and all other informaon hereinaer are for descripon and explanaon only. The

informaon contained in the Manual is subject to change, without noce, due to ﬁrmware

updates or other reasons. Please ﬁnd the latest version of this Manual at the Hikvision

website (hps://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in

supporng the Product.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the properes of Hikvision in

various jurisdicons.

Other trademarks and logos menoned are the properes of their respecve owners.

LEGAL DISCLAIMER

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE

PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED

“AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTO-

RY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU

IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,

DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,

CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH

OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN

CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY

RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL

OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,

HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND

YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE

APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A

MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING

WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA

PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY

PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS

OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR

BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR

EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS

ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW,

THE LATER PREVAILS.

Data Protecon

During the use of device, personal data will be collected, stored and processed. To protect

data, the development of Hikvision devices incorporates privacy by design principles. For

example, for device with facial recognion features, biometrics data is stored in your

device with encrypon method; for ﬁngerprint device, only ﬁngerprint template will be

saved, which is impossible to reconstruct a ﬁngerprint image.

As data controller, you are advised to collect, store, process and transfer data in

accordance with the applicable data protecon laws and regulaons, including without

limitaon, conducng security controls to safeguard personal data, such as, implemenng

reasonable administrave and physical security controls, conduct periodic reviews and

assessments of the eﬀecveness of your security controls.

Scan the QR code to get the user manual for detailed informaon.

Note that mobile data charges may apply if Wi-Fi is unavailable.

Use only power supplies listed in the user instrucons:

Model Manufacturer Standard

C2000IC12.0-24P-DE

C2000IC12.0-24P-GB

MOSO Power Supply Technology Co., Ltd.

CEE

MOSO Power Supply Technology Co., Ltd.

ADS-24S-12 1224GPG Shenzhen Honor Electronic Co., Ltd. CEE

Installaon Environment:

If installing the device indoors, the device should be at least 2 meters

away from the light, and at least 3 meters away from the window or the

door.

Make sure the environment illuminaon is more than 100 Lux.

Direct Sunlight

through Window

Indirect Sunlight

through Window

Backlight

10Lux ＞1200Lux100~850Lux

Close to Light

Appearance

3.1

Device Wiring (Without Secure Door Control Unit)

165 mm

1398.95 mm

172 mm

250.71 mm

46 mm

144.71 mm

37 mm

185.91 mm

1347.28 mm

Touch Screen

IR Light IR Light

Camera

White Light

Thermal Module

69.96 mm

Summary of content (2 pages)

PAGE 1
Appearance 2 Installation Installation Environment: 69.96 mm Thermal Module If installing the device indoors, the device should be at least 2 meters away from the light, and at least 3 meters away from the window or the door. Make sure the environment illumination is more than 100 Lux.
PAGE 2
4 3.2 Device Wiring (With Secure Door Control Unit) Face Recognition Terminal Sensor Input RS-485 B1 Yellow B2 Blue B3 Red/Black 5 Secure Door Control Unit Secure Door Control Unit Wiring Terminal Exit Button Lock Output Power on and wire the network cable after installation. You should activate the device before the ﬁrst login.