DS-K1T673 Series Face Recognition Terminal User Manual
DS-K1T673 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T673 Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
DS-K1T673 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T673 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T673 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T673 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T673 Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T673 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model Wireless DS-K1T673DX 13.56 MHz Card Presenting Frequency DS-K1T673DWX 13.56 MHz Card Presenting Frequency, Wi-Fi DS-K1T673TDX 13.56 MHz Card Presenting Frequency DS-K1T673TDWX 13.56 MHz Card Presenting Frequency, Wi-Fi DS-K1T673TDGX 13.56 MHz Card Presenting Frequency, 4G Use only power supplies listed in the user instructions: Model Manufacturer Standard C2000IC12.
DS-K1T673 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features ................................................................................................................................. 1 1.2.
DS-K1T673 Series Face Recognition Terminal User Manual 6.1 Select Language ................................................................................................................... 34 6.2 Set Application Mode .......................................................................................................... 36 6.3 Privacy Settings .................................................................................................................... 37 6.4 Set Administrator ....................
DS-K1T673 Series Face Recognition Terminal User Manual 7.5.1 Authenticate via Single Credential .............................................................................. 61 7.5.2 Authenticate via Multiple Credential .......................................................................... 62 7.6 Basic Settings ....................................................................................................................... 63 7.7 Set Biometric Parameters ..........................................
DS-K1T673 Series Face Recognition Terminal User Manual 8.5.6 Upgrade and Maintenance ......................................................................................... 83 8.5.7 Log Query .................................................................................................................... 85 8.5.8 Security Mode Settings ............................................................................................... 85 8.5.9 Certificate Management .........................................
DS-K1T673 Series Face Recognition Terminal User Manual 9.4.1 Add Organization ...................................................................................................... 119 9.4.2 Import and Export Person Identify Information ........................................................ 119 9.4.3 Get Person Information from Access Control Device ................................................ 122 9.4.4 Issue Cards to Persons in Batch ...................................................................
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features 1.2.1 Features (Normal Series) ● ● ● ● ● ● ● ● ● ● 8-inch LCD touch screen, 800 × 1280 pixel resolution 2 MP wide-angle dual-lens Face recognition distance: 0.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● ● ● ● ● ● ● ● ● ● ● ● ● Supports tamper alarm, door opening alarm by external force, duress card and duress password alarm Support multiple display modes, including normal mode, advertisement mode, and simple mode.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Support multiple people recognition (up to 5 people) Support mask wearing detection Supports tamper alarm, door opening alarm by external force, duress card and duress password alarm Support multiple display modes, including normal mode, advertisement mode, and simple mode.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 2 Appearance Refer to the following contents for detailed information of the face recognition terminal: Figure 2-1 Face Recognition Terminal Diagram Table 2-1 Description of Face Recognition Terminal No.
DS-K1T673 Series Face Recognition Terminal User Manual No. Name Note For connecting to the peripheral module. 4 IR Light 5 Camera 6 Breathing Light 7 Loudspeaker 8 Wiring Terminal 9 Temperature Module Interface 10 Debugging Port (For debugging only) 11 Network Interface 12 Audio Output Note If the audio plug diameter is greater than 8 mm, an external adapter is required. 13 Tamper 14 SIM Card Slot Note The SIM card slot varies with different models.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. If you have to install the device outdoors, you should install a protective shield (optional) for the device. Note For details about installation environment, see Tips for Installation Environment. 3.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-1 Install Gang Box 2. Secure the mounting plate on the gang box with 2 supplied screws (SC-K1A4X24_5).
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-2 Install Mounting Plate 3. Route the cable through the cable hole, wire the cables and insert the cables in the gang box.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-3 Secure Device Note Apply Silicone sealant among the cable wiring area to keep the raindrop from entering. 4. Align the device with the mounting plate, and secure the device on the mounting plate with 1 supplied screw (SC-KM3X6-H2-SUS).
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-4 Secure Device 5. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.3 Surface Mounting Steps Note The additional force shall be equal to three times the weight of the equipment. The equipment ad its associated mounting means shall remain secure during the installation.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-5 Mounting Template 2. Drill holes on the wall or other surface according to the Hole 1 on the mounting template. 3. Remove the cable hole on the mounting plate with tools. 4. Align the holes to the mounting plate and secure the mounting plate on the wall with the 2 supplied screws (K1A×24).
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-6 Install Mounting Plate 5. Route the cable through the cable hole of the mounting plate, and connect to corresponding peripherals cables. Note If the device is installed outdoor, you should apply silicone sealant to the wiring exit to avoid water from entering.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-7 Apply Silicone Sealant 6. Align the device with the mounting plate and hang the device on the mounting plate. Figure 3-8 Hang Device 7. Use 1 supplied screw (KM3×6) to secure the device and the mounting plate.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-9 Secure Device 8. Optional: Connect the peripheral module according to your actual needs. 9. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen. 3.4 Mount With Bracket 3.4.1 Preparation before Mounting with Bracket Steps 1. Drill holes on the turnstile's surface according to the figure displayed below. And install waterproof nut.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-10 Drill Holes on Turnstile 2. If the installation angle needs to be 180° perpendicular to the body of the turnstile, the following operations are required. 1) Take off the 3 screws shown in the following figure. Figure 3-11 Take off Screws 2) Rotate the fixed part by 180°, and install the 3 screws back.
DS-K1T673 Series Face Recognition Terminal User Manual 3.4.2 Mount Bracket Steps 1. Pass the bracket bottom through the turnstile, and fix it into the turnstile with self-contained nut. Adjust the bracket to the suitable angle, and fix the nut tightly by the wrench. Figure 3-13 Fix Bracket 2. Fix the mounting plate into the bracket by 4 K1M4×8-SUS screws.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-14 Fix Mounting Plate 3. Pass face recognition terminal cables through the cable hole, and insert them into the inner turnstile. Fix the face recognition terminal into the mounting plate with KM3×6-H2-SUS screws.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 3-15 Fix Face Recognition Terminal 4. After installation, for the proper use of the device (outdoor use), stick the protection film (parts of models supplied) on the screen.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 4 Wiring The device supports connecting to the RS-485 terminal, the door lock, the exit button, the alarm output/input devices, the Wiegand card reader, the access controller, and the power supply. You can wire the peripherals according to the descriptions below.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 4-1 Terminal Diagram The descriptions of the terminals are as follows: 20
DS-K1T673 Series Face Recognition Terminal User Manual Table 4-1 Terminal Descriptions Group Group A No.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 4-2 Device Wiring ● ● ● Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . Do not wire the device to the electric supply directly. 4.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 4-3 Secure Door Control Unit Wiring Note The secure door control unit should connect to an external power supply separately. The suggested external power supply is 12V, 0.5A. 4.4 Wire Fire Module 4.4.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 4-4 Wire Device Figure 4-5 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 4-6 Wiring Device Figure 4-7 Wiring Secure Door Control Unit 4.4.
DS-K1T673 Series Face Recognition Terminal User Manual Scenario: Installed in Entrance/Exit with Fire Linkage ● ● Note The Uninterpretable Power Supply (UPS) is required. The fire system (NC and COM, normally closed when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NC and COM are open.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 4-9 Wiring Diagram 27
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 5-1 Activation Page Caution The password strength of the device can be automatically checked.
DS-K1T673 Series Face Recognition Terminal User Manual characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Note Characters containing admin and nimda are not supported to be set as activation password.
DS-K1T673 Series Face Recognition Terminal User Manual 5.3 Activate via SADP SADP is a tool to detect, activate and modify the IP address of the device over the LAN. Before You Start ● Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. ● The device and the PC that runs the SADP tool should be within the same subnet. The following steps show how to activate a device and modify its IP address.
DS-K1T673 Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP. 3) Input the admin password and click Modify to activate your IP address modification. 5.
DS-K1T673 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 6-1 Select System Language By default, the system language is English. Note After you change the system language, the device will reboot automatically.
DS-K1T673 Series Face Recognition Terminal User Manual 6.2 Set Application Mode After activating the device, you should select an application mode for better device application. Steps 1. On the Welcome page, select Indoor or Others from the drop-down list. Figure 6-2 Welcome Page 2. Tap OK to save.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T673 Series Face Recognition Terminal User Manual Upload Captured Pic. When Auth. (Upload Captured Picture When Authenticating) Upload the pictures captured when authenticating to the platform automatically. Save Captured Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device. Save Registered Pic. (Save Registered Picture) The registered face picture will be saved to the system if you enable the function.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 6-4 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm. : Enter the card No. or present card on the card presenting area. Click OK.
DS-K1T673 Series Face Recognition Terminal User Manual Hik-Connect is enabled/disabled. / / The device wired network is connected/not connected/connecting failed. / / The device' Wi-Fi is enabled and connected/not connected/enabled but not connected. Shortcut Keys Description Note You can configure those shortcut keys displayed on the screen. For details, see Basic Settings . ● ● Enter the device room No. and tap OK to call. Tap to call the center.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-1 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login.
DS-K1T673 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter password entering page. 2. Enter the password. - If you have added an administrator for the device, tap and enter the password. - If you haven't added an administrator for the device, enter the password. 3. Tap OK to enter the home page. Note The device will be locked for 30 minutes after 5 failed password attempts.
DS-K1T673 Series Face Recognition Terminal User Manual 7.2 Communication Settings You can set the wired network, the Wi-Fi parameter, the RS-485 parameters, the Wiegand parameters, ISUP and access to Hik-Connect on the communication settings page. 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IPv4/IPv6 IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-4 Wired Network Settings 3. Set IPv4/IPv6 IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually.
DS-K1T673 Series Face Recognition Terminal User Manual Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server. 7.2.2 Set Wi-Fi Parameters You can enable the Wi-Fi function and set the Wi-Fi related parameters. Steps Note The function should be supported by the device. 1. Tap Comm.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And tap OK.
DS-K1T673 Series Face Recognition Terminal User Manual Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically. - If disable DHCP, you should enter the IP address, the subnet mask, and the gateway manually. 6. Tap OK to save the settings and go back to the Wi-Fi tab. to save the network parameters. 7. Tap 7.2.
DS-K1T673 Series Face Recognition Terminal User Manual 7.2.4 Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wiegand to enter the Wiegand tab. Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. ● Output: A face recognition terminal can connect an external access controller.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-8 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. Central Group Enable central group and the data will be uploaded to the center group. Main Channel Support N1 or None. ISUP Enable ISUP function and the data will be uploaded via EHome protocol. Address Type Select an address type according to your actual needs.
DS-K1T673 Series Face Recognition Terminal User Manual IP Address Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535. Device ID Set device serial no. Password If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only. ● ● Note Remember the ISUP account and ISUP key.
DS-K1T673 Series Face Recognition Terminal User Manual 7.3.1 Add Administrator The administrator can log in the device backend and configure the device parameters. Steps 1. Long tap on the initial page and log in the backend. 2. Tap User → + to enter the Add User page. 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4.
DS-K1T673 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5. Optional: Add a face picture, fingerprints, cards, or Pin for the administrator. ● Note For details about adding a face picture, see Add Face Picture . ● Note For details about adding a fingerprint, see Add Fingerprint . ● For details about adding a card, see Add Card .
DS-K1T673 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Face Picture field to enter the face picture adding page. Figure 7-9 Add Face Picture 6. Look at the camera.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture . After completely adding the face picture, a captured face picture will be displayed at the upper right corner of the page. 7. Tap Save to save the face picture. 8.
DS-K1T673 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the Fingerprint field to enter the Add Fingerprint page. 6. Follow the instructions to add a fingerprint. Note ● The same fingerprint cannot be repeatedly added. ● Up to 10 fingerprints can be added for one user.
DS-K1T673 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 6. Tap the Card field and tap +. 7. Configure the card No. - Enter the card No. manually. - Present the card over the card presenting area to get the card No. Note ● The card No. cannot be empty. ● Up to 20 characters are allowed in the card No. ● The card No. cannot be duplicated. 8.
DS-K1T673 Series Face Recognition Terminal User Manual Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● The suggested user name should be within 32 characters. 5. Tap the PIN code to view the PIN code. Note The PIN code cannot be edited. It can only be applied by the platform. 6. Set the user role. Administrator The user is the administrator.
DS-K1T673 Series Face Recognition Terminal User Manual Search User On the User Management page, Tap the search area to enter the Search User page. Tap Card on the left of the page and select a search type from the drop-down list. Enter the employee ID, card No., or the user name for search. Tap to search. Edit User On the User Management page, select a user from the user list to enter the Edit User page. Follow the steps in User Management to edit the user parameters. Tap to save the settings.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● ● ● The imported pictures should be saved in the folder (named enroll_pic) of the root directory and the picture's name should be follow the rule below: Card No._Name_Department_Employee ID_Gender.jpg If the folder enroll_pic cannot save all imported pictures, you can create another folders, named enroll_pic1, enroll_pic2, enroll_pic3, enroll_pic4, under the root directory. The employee ID should be less than 32 characters.
DS-K1T673 Series Face Recognition Terminal User Manual Face forward at the camera and start authentication via face. Fingerprint Place the enrolled fingerprint on the fingerprint module and start authentication via fingerprint. Card Present the card on the card presenting area and start authentication via card. Note The card can be normal IC card, or encrypted card. QR Code Put the QR code in front of the device camera to authenticate via QR code.
DS-K1T673 Series Face Recognition Terminal User Manual 7.6 Basic Settings You can set the shortcut key, theme, voice settings, time settings, sleeping (s), community No., building No., Unit No., and beauty. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and login the device home page. Tap Basic.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● Note Only devices connected to the QR code module support QR code function. You can select call type from Call Room, Call Center, Call Specified Room No. and Call APP. Call Room When you tap the call button on the authentication page, you should dial a room No. to call. Call Center When you tap the call button on the authentication page, you can call the center directly. Call Specified Room No. You should set a room No.
DS-K1T673 Series Face Recognition Terminal User Manual Set the device installed building No. Unit No. Set the device installed unit No. Beauty You can enable the beauty function and set the smooth and the whiten parameter. Tap + or - to control the effect strength. Note By default, the function is disabled. 7.7 Set Biometric Parameters You can customize the face parameters to improve the face recognition performance.
DS-K1T673 Series Face Recognition Terminal User Manual Parameter Description Face 1:N Security Level Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face 1:1 Security Level Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate.
DS-K1T673 Series Face Recognition Terminal User Manual 7.8 Set Access Control Parameters You can set the access control permissions, including the functions of authentication mode, enable NFC card, enable M1 card, door contact, open duration (s) and authentication interval (s). On the Home page, tap ACS (Access Control Settings) to enter the Access Control Settings page. Edit the access control parameters on this page.
DS-K1T673 Series Face Recognition Terminal User Manual Parameter Description ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. If you adopt multiple authentication modes, you should authenticate other methods before authenticating face. Reader Auth.
DS-K1T673 Series Face Recognition Terminal User Manual Tap T&A Status to enter the T&A Status page. Figure 7-13 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-14 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication.
DS-K1T673 Series Face Recognition Terminal User Manual Steps 1. Tap T&A Status to enter the T&A Status page. 2. Set the Attendance Mode as Auto. Figure 7-15 Auto Attendance Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule.
DS-K1T673 Series Face Recognition Terminal User Manual Example If set the Break Out as Monday 11:00, and Break In as Monday 12:00, the valid user's authentication from Monday 11:00 to 12:00 will be marked as break. 7.9.4 Set Manual and Auto Attendance via Device Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication.
DS-K1T673 Series Face Recognition Terminal User Manual 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday. 3) Set the selected attendance status's start time of the day. 4) Tap OK. 5) Repeat step 1 to 4 according to your actual needs. Note The attendance status will be valid within the configured schedule. Result On the initial page and authenticate.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 7-17 Maintenance Page System Information You can view the device model, serial No., versions, address, production data, QR code, and open source code license. Note The page may vary according to different device models. Refers to the actual page for details. Capacity You can view the number of, user, face picture, card, event and fingerprint. Note Parts of the device models support displaying the fingerprint number.
DS-K1T673 Series Face Recognition Terminal User Manual Plug the USB flash drive in the device USB interface. Tap Upgrade, and the device will read the digicap.dav file in the USB flash drive to start upgrading. Unlink APP Account After unlinking APP account, you cannot operate via APP. Restore to Default Settings All parameters, except for the communication settings, remotely imported user information, will be restored to the default settings. The system will reboot to take effect.
DS-K1T673 Series Face Recognition Terminal User Manual 7.11.2 Call Center from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4. Add the main station and the device to the client software. Note For details about adding device, see Add Device. 5.
DS-K1T673 Series Face Recognition Terminal User Manual 7. Click Start Two-Way Audio to start two-way audio between the device and the client software. 7.11.4 Call Room from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up. 3. Click Device Management to enter the Device Management interface. 4.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 8 Operation via Web Browser 8.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:".
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-1 Live View Page Function Descriptions: Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Unlock the linked door. Start or stop live view. Start or stop video recording.
DS-K1T673 Series Face Recognition Terminal User Manual Select the streaming type when starting live view. You can select from the main stream and the sub stream. Select the window division type when starting live view. Full screen view. 8.3 Person Management Click and add the person's information, including the basic information, card, authentication mode, and the Click OK to save the person. Add Basic Information Click User → Add to enter the Add Person page.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-2 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 8.5 Configuration 8.5.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path. Set Live View Parameters Click Configuration → Local to enter the Local page.
DS-K1T673 Series Face Recognition Terminal User Manual You can also click Open to open the file folder to view details. 8.5.2 View Device Information View the device name, language, model, serial No., QR code, version, number of channels, alarm input, alarm output, lock and RS-485, device capacity, etc. Click Configuration → System → System Settings → Basic Information to enter the configuration page. You can view the device name, language, model, serial No.
DS-K1T673 Series Face Recognition Terminal User Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 8.5.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 8-4 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 8.5.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K1T673 Series Face Recognition Terminal User Manual Upgrade Click Configuration → System → Maintenance → Upgrade & Maintenance . Select an upgrade type from the drop-down list. Click and select the upgrade file from your local PC. Click Upgrade to start upgrading. Note Do not power off during the upgrading. 8.5.7 Log Query You can search and view the device logs. Go to Configuration → System → Maintenance → Log Query . Set the major and minor type of the log type.
DS-K1T673 Series Face Recognition Terminal User Manual 8.5.9 Certificate Management It helps to manage the server/client certificates and CA certificate. Note The function is only supported by certain device models. Create and Install Self-signed Certificate Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Certificate Files area, select a Certificate Type from the drop-down list. 3. Click Create. 4. Input certificate information. 5.
DS-K1T673 Series Face Recognition Terminal User Manual Steps 1. Go to Configuration → System → Security → Certificate Management . 2. Create an ID in the Inport CA Certificate area. Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install. 8.5.10 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK.
DS-K1T673 Series Face Recognition Terminal User Manual Note Some device models do not support Wi-Fi settings. Refer to the actual products when configuration. Set Basic Network Parameters Click Configuration → Network → Basic Settings → TCP/IP . Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, IPv6 mode, IPv6 address, IPv6 subnet prefix length, IPv6 default gateway, Mac address, and MTU.
DS-K1T673 Series Face Recognition Terminal User Manual Set Wi-Fi Parameters Set the Wi-Fi parameters for device wireless connection. Steps Note The function should be supported by the device. 1. Click Configuration → Network → Basic Settings → Wi-Fi . Figure 8-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add, and enter the SSID, working mode, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4.
DS-K1T673 Series Face Recognition Terminal User Manual You can set the center group and the system will transfer logs via ISUP protocol. Click Save to save the settings. Center Group Select a center group from the drop-down list. Main Channel The device will communicate with the center via the main channel. Note N1 refers to wired network. Set ISUP Parameters Set the ISUP parameters for accessing device via ISUP protocol. Steps Note The function should be supported by the device. 1.
DS-K1T673 Series Face Recognition Terminal User Manual 3. Optional: Click Test to test whether the entered IP address or host name are valid. 4. Optional: Click Default to reset the destination IP or host name. 5. Click Save. 8.5.13 Set Video and Audio Parameters Set the image quality, resolution, and the device volume. Set Video Parameters Click Configuration → Video/Audio → Video .
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-8 Set Audio Parameters Drag the block to adjust the device input and output volume. Click Save to save the settings after the configuration. You can also enable Voice Prompt. Note The functions vary according to different models. Refers to the actual device for details. 8.5.14 Customize Audio Content Customize the output audio content when authentication succeeded and failed. Steps 1. Click Configuration → Video/Audio → Prompt .
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-9 Customize Audio Content 2. Set the appellation. 3. Enable the function. 4. Set the time duration when authentication succeeded. 1) Click Add. 2) Set the time duration and the language. Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. 5.
DS-K1T673 Series Face Recognition Terminal User Manual 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. 6. Optional: Import custom prompt. 1) Select Custom Type. 2) Select the importing path, and click Import. 7. Click Save to save the settings. 8.5.15 Set Image Parameters Set the video standard, WDR, brightness, contrast, and saturation. Steps 1. Click Configuration → Image Adjustment . 2.
DS-K1T673 Series Face Recognition Terminal User Manual 8.5.16 Set Supplement Light Brightness Set the device supplement light brightness. Steps 1. Click Configuration → Image → Supplement Light Parameters . 2. Select a supplement light type and mode from the drop-down list. If you select the mode as ON, you should set the brightness. 8.5.17 Set Beauty Parameters You can enable beauty camera and set the parameters. Steps 1. Click Configuration → Image → Beauty Parameters . 2.
DS-K1T673 Series Face Recognition Terminal User Manual Time Settings Steps 1. Click Configuration → Time Settings to enter the settings page. 2. Select Status Type. 3. Optional: Edit Schedule Name according to the actual needs. 4. Drag mouse to set the schedule. Note Set the schedule from Monday to Sunday according to the actual needs. 5. Optional: Select a timeline and click Delete. Or click Delete All to clear the settings. 6. Click Save.
DS-K1T673 Series Face Recognition Terminal User Manual Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Auto. 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. 6. Set the status' schedule.
DS-K1T673 Series Face Recognition Terminal User Manual 8.5.19 General Settings Set Authentication Parameters Click Configuration → General → Authentication Settings . Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration. Card Reader Select Main Card Reader or Sub Card Reader from the drop-down list. Main Card Reader You can configure the device card reader's parameters.
DS-K1T673 Series Face Recognition Terminal User Manual Enable to report alarm when the card reading attempts reach the set value. Enable Tampering Detection Enable the anti-tamper detection for the card reader. Enable Card No. Reversing The read card No. will be in reverse sequence after enabling the function. If select Sub Card Reader: Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Enable Card Reader Enable the card reader's function.
DS-K1T673 Series Face Recognition Terminal User Manual Enable the anti-tamper detection for the card reader. Set Privacy Parameters Set the event storage type, picture upload and storage parameters, and the picture clearing parameters. Go to Configuration → General → Privacy . Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting.
DS-K1T673 Series Face Recognition Terminal User Manual If you enable this function, you can save the picture captured by linked camera to the device. Clear All Pictures in Device Note All pictures cannot be restored once they are deleted. Clear Registered Face Pictures All registered pictures in the device will be deleted. Clear Captured Pictures All captured pictures in the device will be deleted. Set Face Recognition Parameters You can set face recognition parameters for accessing.
DS-K1T673 Series Face Recognition Terminal User Manual Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. Enable DESFire Card The device can read the data from DESFire card when enabling the DESFire card function. DESFire Card Read Content After enable the DESFire card content reading function, the device can read the DESFire card content.
DS-K1T673 Series Face Recognition Terminal User Manual Note If you change the device type, you should reboot the device. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device. Phase No. Set the device phase No. Building No. Set the device building No. Unit No. Set the device unit No. Note If you change the No., you should reboot the device.
DS-K1T673 Series Face Recognition Terminal User Manual Note Only the access control device and other devices or systems (such as door station, indoor station, main station, platform) are in the same IP segment, the two-way audio can be performed. Go to Configuration → Video Intercom → Linked Network Settings . Set the main station's IP address and SIP server's IP address. Click Save. Press Button to Call Steps 1. Click Intercom → Press Button to Call to enter the settings page. 2. Set the parameters.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-10 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration.
DS-K1T673 Series Face Recognition Terminal User Manual You can set the door lock status when the door lock is powering off. By default, it is Remain Closed. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended access needs swipes her/his card. Door Remain Open Duration with First Person Set the door open duration when first person is in. After the first person is authorized, it allows multiple persons access the door or other authentication actions.
DS-K1T673 Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No. Baud Rate The baud rate when the devices are communicating via the RS-485 protocol. Set Wiegand Parameters You can set the Wiegand transmission direction. Steps Note Some device models do not support this function.
DS-K1T673 Series Face Recognition Terminal User Manual Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 8.5.22 Set Biometric Parameters Set Basic Parameters Click Configuration → Smart → Smart .
DS-K1T673 Series Face Recognition Terminal User Manual Figure 8-12 Set Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration.
DS-K1T673 Series Face Recognition Terminal User Manual Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not. Note Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
DS-K1T673 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. Face Recognition Timeout Value Set the timeout value when face recognizing. If the face recognition time is longer than the configured value, the system will pop up a prompt.
DS-K1T673 Series Face Recognition Terminal User Manual Click Configuration → Theme . Display Mode You can select display theme for device authentication. You can select Display Mode as Simple, Advertisement Mode or Normal. When you select Simple, the information of name, ID, face picture will be not displayed. When you select Advertisement Mode, the advertisement will be displayed in the screen. Sleep Enable Sleep and the device will enter the sleep mode when no operation within the configured sleep time.
DS-K1T673 Series Face Recognition Terminal User Manual Chapter 9 Client Software Configuration 9.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 9-1 Flow Diagram of Configuration on Client Software 9.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T673 Series Face Recognition Terminal User Manual Example You can control entrance & exit and manage attendance after adding access control devices to the client; you can perform video intercom with the indoor stations and door stations. 9.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and ISUP protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added.
DS-K1T673 Series Face Recognition Terminal User Manual you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. Optional: Check Transmission Encryption (TLS) to enable transmission encryption using TLS 5. (Transport Layer Security) protocol for security purpose.
DS-K1T673 Series Face Recognition Terminal User Manual Address Edit the address of the device. Port Enter the device port number. The default port number is 8000. User Name Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked.
DS-K1T673 Series Face Recognition Terminal User Manual Note For the following operations for resetting the password, contact our technical support. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T673 Series Face Recognition Terminal User Manual 9.3 Group Management The client provides groups to manage the added resources in different groups. You can group the resources into different groups according to the resources' locations. Example For example, on the 1st floor, there mounted 16 doors, 64 alarm inputs, and 16 alarm outputs. You can organize these resources into one group (named 1st Floor) for convenient management.
DS-K1T673 Series Face Recognition Terminal User Manual Note You can click or to switch the resource display mode to thumbnail view or to list view. 6. Click Import to import the selected resources to the group. 9.4 Person Management You can add person information to the system for further operations such as access control, video intercom, time and attendance, etc. You can manage the added persons such as issuing cards to them in a batch, importing and exporting person information in a batch, etc. 9.4.
DS-K1T673 Series Face Recognition Terminal User Manual Import Person Information You can enter the information of multiple persons in a predefined template (CSV/Excel file) to import the information to the client in a batch. Steps 1. Enter the Person module. 2. Select an added organization in the list, or click Add in the upper-left corner to add an organization and then select it. 3. Click Import to open the Import panel. 4. Select Person Information as the importing mode. 5.
DS-K1T673 Series Face Recognition Terminal User Manual Note ● The (folder of) face pictures should be in ZIP format. ● Each picture file should be in JPG format and should be no larger than 200 KB. ● Each picture file should be named as "Person ID_Name". The Person ID should be the same with that of the imported person information. 6. Click Import to start importing. The importing progress and result will be displayed.
DS-K1T673 Series Face Recognition Terminal User Manual ● ● Note The exported file is in ZIP format. The exported face picture is named as "Person ID_Name_0" ("0" is for a full-frontal face). 9.4.3 Get Person Information from Access Control Device If the added access control device has been configured with person information (including person details and issued card information), you can get the person information from the device and import them to the client for further operations.
DS-K1T673 Series Face Recognition Terminal User Manual 3. Optional: Enter key words (name or person ID) in the input box to filter the person(s) that need issuing cards. 4. Optional: Click Settings to set the card issuing parameters. For details, refer to . 5. Click Initialize to initialize the card enrollment station or card reader to make it ready for issuing cards. 6. Click the Card No. column and enter the card number. - Place the card on the card enrollment station. - Swipe the card on the card reader.
DS-K1T673 Series Face Recognition Terminal User Manual Card Enrollment Station Select the model of the connected card enrollment station Note Currently, the supported card enrollment station models include DS-K1F100-D8, DS-K1F100-M, DS-K1F100-D8E, and DS-K1F180-D8E. Card Type This field is only available when the model is DS-K1F100-D8E or DS-K1F180-D8E. Select the card type as EM card or IC card according to the actual card type. Serial Port It is only available when the model is DS-K1F100-M.
DS-K1T673 Series Face Recognition Terminal User Manual Steps Note You can add up to 64 holidays in the software system. 1. Click Access Control → Schedule → Holiday to enter the Holiday page. 2. Click Add on the left panel. 3. Create a name for the holiday. 4. Optional: Enter the descriptions or some notifications of this holiday in the Remark box. 5. Add a holiday period to the holiday list and configure the holiday duration. Note Up to 16 holiday periods can be added to one holiday.
DS-K1T673 Series Face Recognition Terminal User Manual 1. Click Access Control → Schedule → Template to enter the Template page. Note There are two default templates: All-Day Authorized and All-Day Denied, and they cannot be edited or deleted. All-Day Authorized The access authorization is valid in each day of the week and it has no holiday. All-Day Denied The access authorization is invalid in each day of the week and it has no holiday. 2. Click Add on the left panel to create a new template. 3.
DS-K1T673 Series Face Recognition Terminal User Manual 9.6 Set Access Group to Assign Access Authorization to Persons After adding the person and configuring the person's credentials, you can create the access groups to define which person(s) can get access to which door(s) and then apply the access group to the access control device to take effect. Steps When the access group settings are changed, you need to apply the access groups to the devices again to take effect.
DS-K1T673 Series Face Recognition Terminal User Manual Figure 9-2 Display the Selected Person(s) and Access Point(s) 8. After adding the access groups, you need to apply them to the access control device to take effect. 1) Select the access group(s) to apply to the access control device. 2) Click Apply All to Devices start applying all the selected access group(s) to the access control device or door station. 3) Click Apply All to Devices or Apply Changes to Devices.
DS-K1T673 Series Face Recognition Terminal User Manual Note If you change the persons' access information or other related information, you will view the promptAccess Group to Be Applied on the right corner of the client. You can click the prompt to apply the changed data to the device. You can select either Apply Now or Apply Later. Figure 9-4 Data Synchronization 9.
DS-K1T673 Series Face Recognition Terminal User Manual Configure Parameters for Access Control Device After adding the access control device, you can configure its parameters, including overlaying user information on picture, uploading pictures after capturing, saving captured pictures, etc. Before You Start Add access control device to the client. Steps 1. Click Access Control → Advanced Function → Device Parameter .
DS-K1T673 Series Face Recognition Terminal User Manual Press Key to Enter Card Number If you enable this function, you can input the card No. by pressing the key. Wi-Fi Probe If you enable this function, the device can probe the surrounding communication devices' MAC address and upload the MAC address to the system. If the MAC address match the specified MAC address, the system can trigger some linkage actions. 3G/4G If you enable this function, the device can communicate in 3G/4G network.
DS-K1T673 Series Face Recognition Terminal User Manual You can set the exit button as remaining closed or remaining open. Usually, it is remaining open. Door Locked Time After swiping the normal card and relay action, the timer for locking the door starts working. Extended Open Duration The door contact can be enabled with appropriate delay after person with extended accesss needs swipes her/his card.
DS-K1T673 Series Face Recognition Terminal User Manual Steps 1. Click Access Control → Advanced Function → Device Parameter . 2. In the device list on the left, click to expand the door, select a card reader and you can edit the card reader's parameters on the right. 3. Edit the card reader basic parameters in the Basic Information page. ● ● Note The displayed parameters may vary for different access control devices. There are part of parameters listed as follows.
DS-K1T673 Series Face Recognition Terminal User Manual Select the fingerprint recognition level in the drop-down list. Default Card Reader Authentication Mode View the default card reader authentication mode. Fingerprint Capacity View the maximum number of available fingerprints. Existing Fingerprint Number View the number of existed fingerprints in the device. Score The device will score the captured picture according to the yaw angle, pitch angle, and pupillary distance.
DS-K1T673 Series Face Recognition Terminal User Manual user cannot authenticate via the fake face within 5 minutes. Within the 5 minutes, the user can authenticate via the real face twice continuously to unlock. Application Mode You can select indoor or others application modes according to actual environment. 4. Click OK. 5. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page to the selected card reader(s).
DS-K1T673 Series Face Recognition Terminal User Manual Passing Mode Select the controller which will control the barrier status of the device. ● If you select According to Lane Controller's DIP Settings, the device will follow the lane controller's DIP settings to control the barrier. The settings on the software will be invalid. ● If you select According to Main Controller's Settings, the device will follow the settings of the software to control the barrier.
DS-K1T673 Series Face Recognition Terminal User Manual 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click Face Recognition Terminal. 4. Set the parameters. Note These parameters displayed vary according to different device models. COM Select a COM port for configuration. COM1 refers to the RS-485 interface and COM2 refers to the RS-232 interface.
DS-K1T673 Series Face Recognition Terminal User Manual 5. Set the baud rate, data bit, the stop bit, parity type, communication mode, working mode, and connection mode in the drop-down list. Note When the connection mode is Connect Access Control Device, you can select Card No. or Person ID as the output type. 6. Click Save. ● The configured parameters will be applied to the device automatically. ● When you change the working mode or connection mode, the device will reboot automatically.
DS-K1T673 Series Face Recognition Terminal User Manual 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click M1 Card Encryption to enter the M1 Card Encryption page. 4. Set the switch to on to enable the M1 card encryption function. 5. Set the sector ID. The sector ID ranges from 1 to 100. 6. Click Save to save the settings. 9.
DS-K1T673 Series Face Recognition Terminal User Manual Note For Remain All Unlocked and Remain All Locked, ignore this step. 4. Click the following buttons to control the door. Unlock When the door is locked, unlock it and it will be open for once. After the open duration, the door will be closed and locked again automatically. Lock When the door is unlocked, lock it and it will be closed. The person who has the access authorization can access the door with credentials.
DS-K1T673 Series Face Recognition Terminal User Manual Before You Start You have added person(s) and access control device(s) to the client. For details, refer to Person Management and Add Device . Steps 1. Click Monitoring to enter monitoring module. Real-time access records are displayed on the bottom of the page. You can view record details, including card No., person name, event time, door location, temperature, authentication type etc.
DS-K1T673 Series Face Recognition Terminal User Manual to view surveillance details (including person's detailed information and the 7. Optional: Click captured picture). Note In the pop-up window, you can click to view surveillance details in full screen.
DS-K1T673 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T673 Series Face Recognition Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize.
DS-K1T673 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.3 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T673 Series Face Recognition Terminal User Manual Size Make sure your face is in the middle of the collecting window.
DS-K1T673 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2.
DS-K1T673 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T673 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD24660B-A