DS-K1T343 Series Face Recognition Terminal User Manual
DS-K1T343 Series Face Recognition Terminal User Manual Legal Information ©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
DS-K1T343 Series Face Recognition Terminal User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed.
DS-K1T343 Series Face Recognition Terminal User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
DS-K1T343 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DS-K1T343 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.
DS-K1T343 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Dangers: Follow these safeguards to prevent serious injury or death.
DS-K1T343 Series Face Recognition Terminal User Manual Cautions: ● ● ● ● ● ● ● ● ● ● ● ● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
DS-K1T343 Series Face Recognition Terminal User Manual Available Models Product Name Face Recognition Terminal Model DS-K1T343MX DS-K1T343MWX DS-K1T343MFX DS-K1T343MFWX DS-K1T343EX DS-K1T343EWX DS-K1T343EFX DS-K1T343EFWX Use only power supplies listed in the user instructions: Model ADS-12FG-12N 12012EPG Manufacturer Shenzhen Honor Electronic Co.
DS-K1T343 Series Face Recognition Terminal User Manual Contents Chapter 1 Overview .................................................................................................................... 1 1.1 Overview ................................................................................................................................ 1 1.2 Features .................................................................................................................................
DS-K1T343 Series Face Recognition Terminal User Manual 7.1 Login .................................................................................................................................... 22 7.1.1 Login by Administrator ................................................................................................ 22 7.1.2 Login by Activation Password ...................................................................................... 23 7.1.3 Forgot Password ...................................
DS-K1T343 Series Face Recognition Terminal User Manual 7.8 Set Access Control Parameters ............................................................................................ 44 7.9 Time and Attendance Status Settings .................................................................................. 45 7.9.1 Disable Attendance Mode via Device ......................................................................... 45 7.9.2 Set Manual Attendance via Device ............................................
DS-K1T343 Series Face Recognition Terminal User Manual 9.5.3 Set Time ...................................................................................................................... 79 9.5.4 Set DST ........................................................................................................................ 80 9.5.5 View Open Source Software License ........................................................................... 80 9.5.6 Upgrade and Maintenance .................................
DS-K1T343 Series Face Recognition Terminal User Manual 10.3.2 Import Resources to Group ..................................................................................... 114 10.4 Person Management ........................................................................................................ 114 10.4.1 Add Organization .................................................................................................... 115 10.4.2 Import and Export Person Identify Information ....................
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 1 Overview 1.1 Overview Face recognition terminal is a kind of access control device for face recognition, which is mainly applied in security access control systems, such as logistic centers, airports, university campuses, alarm centrals, dwellings, etc. 1.2 Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 4.3-inch LCD touch screen 2 MP wide-angle dual-lens Face anti-spoofing Face recognition distance: 0.3 m to 1.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 2 Appearance The appearance of the device with fingerprint is as follows: Figure 2-1 Appearance(With Fingerprint) The appearance of the device without fingerprint is as follows: Figure 2-2 Appearance(Without Fingerprint) Table 2-1 Appearance Description No.
DS-K1T343 Series Face Recognition Terminal User Manual No. Name 4 IR Light 5 Power Interface 6 Camera 7 Camera 8 IR Light 9 Card Presenting Area 10 Fingerprint Module Note Only devices that support the fingerprint function contain a fingerprint module.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 3 Installation 3.1 Installation Environment ● ● Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. Note For details about installation environment, see Tips for Installation Environment. 3.2 Install with Gang Box Steps 1. Make sure the gang box is installed on the wall. Note You should purchase the gang box separately.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 3-2 Install Mounting Plate 3. Route the cables through the cable hole of the mounting plate, and connect to the corresponding peripherals cables. 4. Buckle into the mounting plate after aligning the device with the mounting plate. Use 1 supplied screw (M3) to secure the device on the mounting plate.
DS-K1T343 Series Face Recognition Terminal User Manual 3.3 Base Mounting Steps 1. Route the cables through the cable hole of the bracket, and connect the terminals with peripherals cables. Place the bracket close to the back side of the device. Figure 3-4 Place Bracket Close to Device Back Side 2. Press the bracket with both hands, and make sure that the buckle of the bracket fits with the back side of the device. Fasten the bracket in the direction of the arrow. Figure 3-5 Fasten Bracket 3.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 3-6 Complete Installation 7
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 4 Wiring You can connect the RS-485 terminal with the RS-485 card reader, connect the NC and COM terminal with the door lock, connect the SENSOR terminal with the door contact, the BTN/GND terminal with the exit button, and connect the Wiegand terminal with the Wiegand card reader or the access controller.
DS-K1T343 Series Face Recognition Terminal User Manual Group No. Function Color C3 Group D Name Description White/Black GND Ground White/Purple NC Lock Wiring (NC) D2 White/Yellow COM Common D3 White/Red NO Lock Wiring (NO) D4 Yellow/Green SENSOR Door Contact D5 Black GND Ground D6 Yellow/Gray BUTTON Exit Door Wiring D7 Yellow/Black GND Ground D1 Door Lock 4.2 Wire Normal Device You can connect the terminal with normal peripherals.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● ● Note You should set the face recognition terminal's Wiegand direction as Input to connect to a Wiegand card reader. If connects to an access controller, you should set the Wiegand direction as Output to transmit authentication information to the access controller. For details about Wiegand direction settings, see Set Wiegand Parameters . Do not wire the device to the electric supply directly. 4.
DS-K1T343 Series Face Recognition Terminal User Manual Type 1 Note The fire system controls the power supply of the access control system. Figure 4-3 Wire Device Figure 4-4 Wire Secure Door Control Unit Type 2 Note The fire system (NO and COM, normally open when powering off) is connected with the lock and the power supply in series. When an fire alarm is triggered, the door remains open. In normal times, NO and COM are closed.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 4-5 Wiring Device Figure 4-6 Wiring Secure Door Control Unit 4.4.2 Wiring Diagram of Door Locked When Powering Off Lock Type: Cathode Lock, Electric Lock, and Electric Bolt (NC) Security Type: Door Locked When Powering Off Scenario: Installed in Entrance/Exit with Fire Linkage ● ● Note The Uninterpretable Power Supply (UPS) is required.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 4-7 Device Wiring Figure 4-8 Wiring Diagram 13
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 5 Activation You should activate the device before the first login. After powering on the device, the system will switch to Device Activation page. Activation via the device, SADP tool and the client software are supported. The default values of the device are as follows: ● The default IP address: 192.0.0.64 ● The default port No.: 8000 ● The default user name: admin 5.
DS-K1T343 Series Face Recognition Terminal User Manual Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● ● ● ● After activation, you should select a language according to your actrual needs. After activation, you should select an application mode. For details, see Set Application Mode . After activation, if you need to set privacy, you should check the item. For details, see .
DS-K1T343 Series Face Recognition Terminal User Manual The following steps show how to activate a device and modify its IP address. For batch activation and IP addresses modification, refer to User Manual of SADP for details. Steps 1. Run the SADP software and search the online devices. 2. Find and select your device in online device list. 3. Input new password (admin password) and confirm the password.
DS-K1T343 Series Face Recognition Terminal User Manual Steps Note This function should be supported by the device. 1. Enter the Device Management page. 2. Click on the right of Device Management and select Device. 3. Click Online Device to show the online device area. The searched online devices are displayed in the list. 4. Check the device status (shown on Security Level column) and select an inactive device. 5. Click Activate to open the Activation dialog. 6.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 6 Quick Operation 6.1 Select Language You can select a language for the device system. After the device activation, you can select a language for the device system. Figure 6-1 Select System Language By default, the system language is English. Note After you change the system language, the device will reboot automatically. 6.2 Set Application Mode After activating the device, you should select an application mode for better device application.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 6-2 Welcome Page 2. Tap OK to save. ● ● ● ● Note You can also change the settings in System Settings. If you install the device indoors near the window or the face recognition function is not working well, select Others. If you do not configure the application mode and tap Next, the system will select Indoor by default. If you activate the device via other tools remotely, the system will select Indoor as the application mode by default. 6.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 6-3 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added. : Face forward at the camera. Make sure the face is in the face recognition area. Click to capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm. : Enter the card No. or present card on the card presenting area. Click OK. 4. Click OK. You will enter the authentication page.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● Enter the device room No. and tap OK to call. Tap to call the center. Note The device should be added to the center, or the calling operation will be failed. Enter PIN code to authenticate.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 7 Basic Operation 7.1 Login Login the device to set the device basic parameters. 7.1.1 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page. Figure 7-1 Admin Login 2.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-2 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login. 4. Optional: Tap and you can exit the admin login page. 7.1.2 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login. Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-3 Home Page 7.1.3 Forgot Password If you forget the password during authentication, you can reset the password by imprting the key. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the page. 2. Tap in the pop-up admin authentication page. 3. Tap Forget Password in the upper right corner of the page. 4. Plug USB flash drive into the USB interface.
DS-K1T343 Series Face Recognition Terminal User Manual 7.2.1 Set Wired Network Parameters You can set the device wired network parameters, including the IP address, the subnet mask, the gateway, and DNS parameters. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap Wired Network. Figure 7-4 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway.
DS-K1T343 Series Face Recognition Terminal User Manual Steps Note The function should be supported by the device. 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap. Figure 7-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password.
DS-K1T343 Series Face Recognition Terminal User Manual 7.2.3 Set RS-485 Parameters The face recognition terminal can connect external access controller, secure door control unit or card reader via the RS-485 terminal. Steps 1. Tap Comm. (Communication Settings) on the Home page to enter the Communication Settings page. 2. On the Communication Settings page, tap RS-485 to enter the RS-485 tab. Figure 7-6 Set RS-485 Parameters 3. Select an peripheral type according to your actual needs.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-7 Wiegand Settings 3. Enable the Wiegand function. 4. Select a transmission direction. ● Output: A face recognition terminal can connect an external access controller. And the two devices will transmit the card No. via Wiegand 26 or Wiegand 34. ● Input: A face recognition terminal can connect a Wiegand card reader. 5. Tap to save the network parameters.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-8 ISUP Settings 2. Enable the ISUP function and set the ISUP server parameters. ISUP Version Set the ISUP version according to your actual needs. If you choose V5.0, you should create an account and ISUP key. If you choose other version, you should create an ISUP account only. ● ● Note Remember the ISUP account and ISUP key.
DS-K1T343 Series Face Recognition Terminal User Manual IP Address Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535. Device ID Set device serial no. 7.2.6 Platform Access You can change the device verification code and set the server address before you add the device to the Hik-Connect mobile client. Before You Start Make sure your device has connected to a network. Steps 1. Tap Comm.
DS-K1T343 Series Face Recognition Terminal User Manual 3. Edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers. ● The employee ID should not be duplicated. 4. Tap the Name field and input the user name on the soft keyboard. Note ● Numbers, upper case letters, lower case letters, and special characters are allowed in the user name. ● Up to 32 characters are allowed in the user name. 5.
DS-K1T343 Series Face Recognition Terminal User Manual For details about adding a card, see Add Card . For details about adding a password, see View PIN code . 6. Optional: Set the administrator's authentication type. ● ● Note For details about setting the authentication type, see Set Authentication Mode . 7. Enable the Administrator Permission function. Enable Administrator Permission The user is the administrator.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-9 Add Face Picture 6. Look at the camera. ● ● ● Note Make sure your face picture is in the face picture outline when adding the face picture. Make sure the captured face picture is in good quality and is accurate. For details about the instructions of adding face pictures, see Tips When Collecting/ Comparing Face Picture .
DS-K1T343 Series Face Recognition Terminal User Manual Steps ● ● Note The function should be supported by the device. Up to 3000 fingerprints can be added. 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and enter the device backend. 2. Tap User → + to enter the Add User page. 3. Tap the Employee ID. field and edit the employee ID. Note ● The employee ID should be less than 32 characters.
DS-K1T343 Series Face Recognition Terminal User Manual Steps Note Up to 3000 cards can be added. 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the backend. 2. Tap User → + to enter the Add User page. 3. Connect an external card reader according to the wiring diagram. 4. Tap the Employee ID. field and edit the employee ID. Note ● The employee ID should be less than 32 characters.
DS-K1T343 Series Face Recognition Terminal User Manual 7.3.5 View PIN code Add a PIN code for the user and the user can authenticate via the PIN code. Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture and log in the backend. 2. Tap User → + to enter the Add User page. 3. Tap the Employee ID. field and edit the employee ID. Note ● The employee ID should be less than 32 characters. And it can be a combination of lower letters, upper letters, and numbers.
DS-K1T343 Series Face Recognition Terminal User Manual 2. Tap User → Add User/Edit User → Authentication Mode . 3. Select Device or Custom as the authentication mode. Device If you want to select device mode, you should set the terminal authentication mode in Access Control Settings page first. For details see Setting Access Control Parameters. Custom You can combine different authentication modes together according to your actual needs. to save the settings. 4. Tap 7.3.
DS-K1T343 Series Face Recognition Terminal User Manual 3. Tap User Data, Face Data or Access Control Parameters . Note The imported access control parameters are configuration files of the device. 4. Enter the created password when you exported the data. If you do not create a password when you exported the data, leave a blank in the input box and tap OK immediately.
DS-K1T343 Series Face Recognition Terminal User Manual 7.5 Identity Authentication After network configuration, system parameters configuration and user configuration, you can go back to the initial page for identity authentication. The system will authenticate person according to the configured authentication mode. 7.5.1 Authenticate via Single Credential Set the user authentication type before authentication. For details, see Set Authentication Mode . Authenticate face, fingerprint or card.
DS-K1T343 Series Face Recognition Terminal User Manual ● ● Note For detailed information about scanning fingerprint, see Tips for Scanning Fingerprint. For detailed information about authenticating face, see Tips When Collecting/Comparing Face Picture. If authentication succeeded, the prompt "Authenticated" will pop up. 7.6 Basic Settings You can set the shortcut key, voice, time, language, white light brightness, community No., building No., Unit No., beauty, and advertisement.
DS-K1T343 Series Face Recognition Terminal User Manual shortcut key, voice, time, language, supplement light, community No., building No., and Unit No. Shortcut Key Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function. Note You can select call type from Call Room, Call Center, and Call Specified Room No. Call Room When you tap the call button on the authentication page, you should dial a room No.
DS-K1T343 Series Face Recognition Terminal User Manual You can enable the beauty function and set the smooth and the whiten parameter. Tap + or - to control the effect strength. Note By default, the function is disabled. Advertisement You can enable the advertisement function, and the advertisement will be displayed on the authentication page. The advertisement can be added in web browser. For details, see Set Notice Publication . 7.
DS-K1T343 Series Face Recognition Terminal User Manual Table 7-1 Face Picture Parameters Parameter Description Select Application Mode Select either others or indoor according to actual environment. Face Liveness Level After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication. Face Recognition Distance Set the valid distance between the user and the camera when authenticating.
DS-K1T343 Series Face Recognition Terminal User Manual 7.8 Set Access Control Parameters You can set the access control permissions, including the functions of authentication mode, enable NFC card, door contact, and door open time. On the Home page, tap ACS (Access Control Settings) to enter the Access Control Settings page. Edit the access control parameters on this page.
DS-K1T343 Series Face Recognition Terminal User Manual Parameter Description ● ● ● Note Only the device with the fingerprint module supports the fingerprint related function. Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes. If you adopt multiple authentication modes, you should authenticate other methods before authenticating face. Reader Auth.
DS-K1T343 Series Face Recognition Terminal User Manual Tap T&A Status to enter the T&A Status page. Figure 7-13 Disable Attendance Mode Set the Attendance Mode as Disable. You will not view or configure the attendance status on the initial page. And the system will follow the attendance rule that configured on the platform. 7.9.2 Set Manual Attendance via Device Set the attendance mode as manual, and you should select a status manually when you take attendance.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-14 Manual Attendance Mode 3. Enable the Attendance Status Required. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. Result You should select an attendance status manually after authentication.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 7-15 Auto Attendance Mode 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. The name will be displayed on the T & A Status page and the authentication result page. 6. Set the status' schedule. 1) Tap Attendance Schedule. 2) Select Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or Sunday.
DS-K1T343 Series Face Recognition Terminal User Manual 7.9.4 Set Manual and Auto Attendance via Device Set the attendance mode as Manual and Auto, and the system will automatically change the attendance status according to the configured schedule. At the same time you can manually change the attendance status after the authentication. Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Tap T&A Status to enter the T&A Status page. 2.
DS-K1T343 Series Face Recognition Terminal User Manual Result On the initial page and authenticate. The authentication will be marked as the configured attendance status according to the schedule. If you tap the edit icon on the result tab, you can select a status to take attendance manually, the authentication will be marked as the edited attendance status.
DS-K1T343 Series Face Recognition Terminal User Manual Note Parts of the device models support displaying the fingerprint number. Refers to the actual page for details. Upgrade Plug the USB flash drive in the device USB interface. Tap Upgrade → OK , and the device will read the digicap.dav file in the USB flash drive to start upgrading. Unlink APP Account Unlink the Hik-Connect account from the platform. Restore to Factory All parameters will be restored to the factory settings.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 8 Configure the Device via the Mobile Browser 8.1 Login You can login via mobile browser. ● ● Note Parts of the model supports Wi-Fi settings. Make sure the device is activated. Obtain the IP address from the device after Wi-Fi is enabled. Make sure the IP segment of the device and the computer is the same. For details, refers to Set Wi-Fi Parameters .
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-1 Add User 2) Set the following parameters. Employee ID Enter the employee ID. The Employee ID cannot be 0 or exceed 32 characters. It can be a combination of uppercase, lowercase letters and numbers. Name Enter your name. The name supports numbers, uppercase and lowercase English, and characters. The name is recommended to be within 32 characters. Gender Select the gender. User Role Select your user role. Floor No./Room No.
DS-K1T343 Series Face Recognition Terminal User Manual Enter the floor No./room No. Face Add Face picture. Tap Face, then tapImport, and select the mode to import the face. Fingerprint Add fingerprint. Tap Fingerprint, then tap +, and add fingerprint via the fingerprint module. Start Date/End Date Set Start Date and End Date of user permission. Administrator If the user needs to be set as administrator, you can enable Administrator. Authentication Type Set the authentication type. 3) Tap Save. 3.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-2 Time Settings Tap Save to save the settings. Time Zone Select the time zone where the device is located from the drop-down list. Time Sync. Mode Manual By default, the device time should be synchronized manually. You can set the device time manually. NTP Set the NTP server's IP address, port No., and interval. 8.4.
DS-K1T343 Series Face Recognition Terminal User Manual HTTP It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.0.0.65:81 in the browser for login. RTSP It refers to the port of real-time streaming protocol. HTTPS Set the HTTPS for accessing the browser. Certificate is required when accessing. Server It refers to the port through which the client adds the device.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-3 Wi-Fi 3. Add Wi-Fi. 1) Tap +. Figure 8-4 Add Wi-Fi 2) Enter Wi-Fi Name and Wi-Fi Password, and select Working Mode and Encryption Type.
DS-K1T343 Series Face Recognition Terminal User Manual 3) Tap Save. 4. Select the Wi-Fi name, and tap Connect. 5. Enter the password and tap Save. 6. Set WLAN parameters. 1) Set the IP address, subnet mask, and gateway. Or enable DHCP and the system will allocate the IP address, subnet mask, and gateway automatically. 2) Tap Save. 8.4.5 General Settings Set Authentication Parameters Set Authentication Parameters. Steps 1. Tap Configuration → General Settings → Authentication Settings .
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-5 Authentication Settings 2. Tap Save. Device Type Main Card Reader You can configure the device card reader's parameters. If you select main card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Minimum Card Swiping Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max.
DS-K1T343 Series Face Recognition Terminal User Manual Sub Card Reader You can configure the connected peripheral card reader's parameters. If you select sub card reader, you need to configure the following parameters: Card Reader Type, Card Reader Description, Enable Card Reader, Authentication, Recognition Interval (s), Max. Authentication Failed Attempts Alarm/Alarm of Max. Failed Attempts, Enable Tampering Detection, Communication with Controller Every (s) and Max. Interval When Entering Password (s).
DS-K1T343 Series Face Recognition Terminal User Manual Set Privacy Parameters Set the event storage type, picture upload and storage parameters, and the picture clearing parameters. Tap Configuration → General Settings → Privacy .
DS-K1T343 Series Face Recognition Terminal User Manual 62
DS-K1T343 Series Face Recognition Terminal User Manual Event Storage Settings Select a method to delete the event. You can select from Delete Old Events Periodically, Delete Old Events by Specified Time, or Overwriting. Delete Old Events Periodically Enter number to set the period for event deleting. All events will be deleted according to the configured time duration. Delete Old Events by Specified Time Set a time and all events will be deleted on the configured time.
DS-K1T343 Series Face Recognition Terminal User Manual Clear Registered Face Pictures Select Face Picture, and tap Clear. All registered pictures in the device will be deleted. Clear Authentication/Captured Picture Select Authentication/Captured Picture, and tap Clear. All authentication/captured pictures in the device will be deleted. Set Card Security Tap Configuration → General Settings → Card Security to enter the settings page. Figure 8-7 Card Security Set the parameters and click Save.
DS-K1T343 Series Face Recognition Terminal User Manual Enable EM Card Enable EM card and authenticating by presenting EM card is available. Note If the peripheral card reader supports presenting EM card, the function is also supported to enable/disable the EM card function. Enable CPU Card The device can read the data from CPU card when enabling the CPU card function. CPU Card Read Content After enable the CPU card content reading function, the device can read the CPU card content.
DS-K1T343 Series Face Recognition Terminal User Manual Face Parameters Settings Tap Configuration → Smart → Intelligent Parameter . Figure 8-9 Face Parameters Note The functions vary according to different models. Refers to the actual device for details. Set Face Parameters. Face Anti-spoofing Enable or disable the live face detection function. If enabling the function, the device can recognize whether the person is a live one or not.
DS-K1T343 Series Face Recognition Terminal User Manual Live Face Detection Security Level After enabling the face anti-spoofing function, you can set the matching security level when performing live face authentication. Recognition Distance Select the distance between the authenticating user and the device camera. Application Mode Select Indoor or Others according to actual environment. In the outdoor scene, indoor scene near the window, or bad environment, you can choose Others.
DS-K1T343 Series Face Recognition Terminal User Manual Face Recognition Timeout Value Configure the timeout period for face recognition. If the face recognition time exceeds the configured value, the device will prompt the face recognition timeout. ECO Mode After enabling the ECO mode, the device will use the IR camera to authenticate faces in the low light or dark environment. And you can set the ECO mode threshold, ECO mode (1:N), and ECO mode (1:1).
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-10 Device ID Settings (Door Station) Device Type The device can be used as a door station, outer door station, or access control device. Select a device type from the drop-down list. Note If you change the device type, you should reboot the device. Floor No. Set the device installed floor No. Door Station No. Set the device installed floor No. Note If you change the No., you should reboot the device.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you change the No., you should reboot the device. Configure SIP Parameters Set the device's IP address and the SIP server's IP address. After setting the parameters, you can communicate among the access control device, door station, indoor station, main station, and the platform.
DS-K1T343 Series Face Recognition Terminal User Manual 8.4.8 Access Control Settings Set Door Parameters Tap Configuration → Access Control → Door Parameters . Figure 8-13 Door Parameters Settings Page Click Save to save the settings after the configuration.
DS-K1T343 Series Face Recognition Terminal User Manual Door No. Select the device corresponded door No. Name You can create a name for the door. Open Duration Set the door unlocking duration. If the door is not opened for the set time, the door will be locked. Door Open Timeout Alarm An alarm will be triggered if the door has not been closed within the configured time duration. Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 8-14 RS-485 Page Tap Save to save the settings after the configuration. Peripheral Type Select a peripheral from the drop-down list according the actual situation. You can select from Card Reader, Extension Module, or Access Controller. Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs.
DS-K1T343 Series Face Recognition Terminal User Manual Data Bit The data bit when the devices are communicating via the RS-485 protocol. Stop Bit The stop bit when the devices are communicating via the RS-485 protocol. Parity/Flow Ctrl/Communication Mode Enabled by default. Set Wiegand Parameters You can set the Wiegand transmission direction. Steps 1. Tap Configuration → Access Control → Wiegand Settings . Figure 8-15 Wiegand Page 2. Enable Wiegand to enable the Wiegand function. 3.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 9 Operation via Web Browser 9.1 Login You can login via the web browser or the remote configuration of the client software. Note Make sure the device is activated. For detailed information about activation, see Activation . Login via Web Browser Enter the device IP address in the address bar of the web browser and press Enter to enter the login page. Note Make sure that the IP address starts with "Https:".
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-1 Live View Page Function Descriptions: Select the image size when starting live view. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds. You can capture image when starting live view. Reserved function. You can zoom in the live view image. Start or stop live view. Start or stop video recording. Select the streaming type when starting live view.
DS-K1T343 Series Face Recognition Terminal User Manual 9.3 Person Management Click and add the person's information, including the basic information, card, authentication mode, and the picture. Click OK to save the person. Add Basic Information Click User → Add to enter the Add Person page. Add the person's basic information, including the employee ID, the person's name, the gender, user level, floor No., and room No. Click OK to save the settings. Add Card Click User → Add to enter the Add Person page.
DS-K1T343 Series Face Recognition Terminal User Manual 9.4 Search Event Click Search to enter the Search page. Figure 9-2 Search Page Enter the search conditions, including the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel. 9.5 Configuration 9.5.1 Set Local Parameters Set the live view parameters, record file saving path, and captured pictures saving path.
DS-K1T343 Series Face Recognition Terminal User Manual Set Captured Pictures Saving Path Click Configuration → Local to enter the Local page. Select a saving path from your local computer and click Save. You can also click Open to open the file folder to view details. 9.5.2 View Device Information View the device name, language, model, serial No., QR code, version, number of channels, alarm input, alarm output, lock and RS-485, device capacity, etc.
DS-K1T343 Series Face Recognition Terminal User Manual By default, the device time should be synchronized manually. You can set the device time manually or check Sync. with Computer Time to synchronize the device time with the computer's time. 9.5.4 Set DST Steps 1. Click Configuration → System → System Settings → DST . Figure 9-4 DST Page 2. Check Enable DST. 3. Set the DST start time, end time and bias time. 4. Click Save to save the settings. 9.5.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-5 Upgrade and Maintenance Page Click Reboot to start reboot the device. Restore Parameters Click Configuration → System → Maintenance → Upgrade & Maintenance . Restore All All parameters will be restored to the factory settings. You should activate the device before usage. Default The device will restore to the default settings, except for the device IP address and the user information.
DS-K1T343 Series Face Recognition Terminal User Manual Note Do not power off during the upgrading. 9.5.7 Log Query You can search and view the device logs. Go to Configuration → System → Maintenance → Log Query . Set the major and minor type of the log type. Set the start time and end time for searching, and click Search. The results will be displayed below, which including the No., time, the major type the minor type, the channel No., the local/remote user information, the remote host IP, etc. 9.5.
DS-K1T343 Series Face Recognition Terminal User Manual Note The function is only supported by certain device models. Create and Install Self-signed Certificate Steps 1. Go to Configuration → System → Security → Certificate Management . 2. In the Certificate Files area, select a Certificate Type from the drop-down list. 3. Click Create. 4. Input certificate information. 5. Click OK to save and install the certificate. The created certificate is displayed in the Certificate Details area.
DS-K1T343 Series Face Recognition Terminal User Manual Note The input certificate ID cannot be the same as the existing ones. 3. Upload a certificate file from the local. 4. Click Install. 9.5.10 Change Administrator's Password Steps 1. Click Configuration → User Management . 2. Click . 3. Enter the old password and create a new password. 4. Confirm the new password. 5. Click OK. Caution The password strength of the device can be automatically checked.
DS-K1T343 Series Face Recognition Terminal User Manual Set Basic Network Parameters Click Configuration → Network → Basic Settings → TCP/IP . Set the parameters and click Save to save the settings. DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, MTU, and the device port. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, and the IPv4 default gateway automatically. NIC Type Select a NIC type from the drop-down list.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-6 Wi-Fi Settings Page 2. Check Wi-Fi. 3. Select a Wi-Fi - Click of a Wi-Fi in the list and enter the Wi-Fi password. - Click Add, and enter the SSID, working mode, and encryption type. Click Connect. When the Wi-Fi is connected, click OK. 4. Optional: Set the WLAN parameters. 1) Click Network Settings. 2) Set the IP address, subnet mask, and default gateway.
DS-K1T343 Series Face Recognition Terminal User Manual Platform Access Platform access provides you an option to manage the devices via platform. Steps 1. Click Configuration → Network → Advanced → Platform Access to enter the settings page. 2. Select the Platform Access Mode. Note Hik-Connect is an application for mobile devices. With the App, you can view live image of the device, receive alarm notification and so on. 3. Check the checkbox of Enable to enable the function. 4.
DS-K1T343 Series Face Recognition Terminal User Manual Before You Start The destination IP or host name should support the HTTP protocol/HTTPS protocol to receive the alarm information. Note The function should be supported by the device. Steps 1. Click Configuration → Network → Advanced → HTTP Listening . 2. Edit the destination IP or host name, URL and port. 3. Optional: Click Test to test whether the entered IP address or host name are valid. 4.
DS-K1T343 Series Face Recognition Terminal User Manual Set Audio Parameters Click Configuration → Video/Audio → Audio . Set the audio stream type and audio encoding. You can also drag the block to adjust the device input and output volume. Click Save to save the settings after the configuration. Note The functions vary according to different models. Refers to the actual device for details. 9.5.14 Customize Audio Content Customize the output audio content when authentication succeeded and failed. Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Note If authentication is succeeded in the configured time duration, the device will broadcast the configured content. 3) Enter the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration. 7. Set the time duration when authentication failed. 1) Click Add. 2) Set the time duration and the language.
DS-K1T343 Series Face Recognition Terminal User Manual Video Standard Set the video frame rate when performing live view remotely. After changing the standard, you should reboot the device to take effect. PAL 25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East countries, Europe countries, etc. NTSC 30 frames per second. Suitable for the USA, Canada, Japan, Taiwan (China), Korea, the Philippines, etc. WDR Enable or disable the WDR function.
DS-K1T343 Series Face Recognition Terminal User Manual Figure 9-10 Supplement Light Settings Page 2. Select a supplement light type and mode from the drop-down list. If you select the mode as ON, you should set the brightness. 9.5.
DS-K1T343 Series Face Recognition Terminal User Manual Time Settings Steps 1. Click Configuration → Time Settings to enter the settings page. 2. Select Status Type. 3. Optional: Edit Schedule Name according to the actual needs. 4. Drag mouse to set the schedule. Note Set the schedule from Monday to Sunday according to the actual needs. 5. Optional: Select a timeline and click Delete. Or click Delete All to clear the settings. 6. Click Save.
DS-K1T343 Series Face Recognition Terminal User Manual Before You Start Add at least one user, and set the user's authentication mode. For details, see User Management. Steps 1. Click Configuration → Attendance to enter the settings page. 2. Set the Attendance Mode as Auto. 3. Enable the Attendance Status function. 4. Enable a group of attendance status. Note The Attendance Property will not be changed. 5. Optional: Select an status and change its name if required. 6. Set the status' schedule.
DS-K1T343 Series Face Recognition Terminal User Manual 9.5.18 General Settings Set Authentication Parameters Click Configuration → General → Authentication Settings . Note The functions vary according to different models. Refers to the actual device for details. Figure 9-11 Set Authentication Parameters Click Save to save the settings after the configuration. Device Type Select Main Card Reader or Sub Card Reader from the drop-down list.
DS-K1T343 Series Face Recognition Terminal User Manual If select Main Card Reader: Card Reader Type/Card Reader Description Get card reader type and description. They are read-only. Enable Card Reader Enable the card reader's function. Authentication Select an authentication mode according to your actual needs from the drop-down list. Recognition Interval You can set the interval between 2 continuous recognition of a same person during the authentication.
DS-K1T343 Series Face Recognition Terminal User Manual You can set the authentication interval of the same person when authenticating. The same person can only authenticate once in the configured interval. A second authentication will be failed. Alarm of Max. Failed Attempts Enable to report alarm when the card reading attempts reach the set value. Max. Authentication Failed Attempts Enable to report alarm when the card reading attempts reach the set value.
DS-K1T343 Series Face Recognition Terminal User Manual Authentication Settings Display Authentication Result You can check Face Picture, Name, Employee ID and Temperature, to display the authentication result. Name De-identification You can check Name De-identification, and the whole name will not be displayed. Picture Uploading and Storage Upload Captured Picture When Authenticating Upload the pictures captured when authenticating to the platform automatically.
DS-K1T343 Series Face Recognition Terminal User Manual Set Card Security Click Configuration → General → Card Security to enter the settings page. Set the parameters and click Save. Enable NFC Card In order to prevent the mobile phone from getting the data of the access control, you can enable NFC card to increase the security level of the data. Enable M1 Card Enable M1 card and authenticating by presenting M1 card is available.
DS-K1T343 Series Face Recognition Terminal User Manual The device will read card via Wiegand 34 protocol (read 4 bytes). 9.5.19 Video Intercom Settings Set Video Intercom Parameters The device can be used as a door station, outer door station, or access control device. You should set the device No. before usage. Click Configuration → Video Intercom → Device No. . Figure 9-12 Set Video Intercom Parameters If set the device type as Door Station and Access Control Device, you can set the floor No.
DS-K1T343 Series Face Recognition Terminal User Manual Note If you change the No., you should reboot the device. Community No. Set the device installed community No. Building No. Set the device installed building No. Unit No. Set the device installed unit No. If set the device type as Outer Door Station, you can set the outer door station No., and click Advanced Settings to set the community No. Outer Door Station No.
DS-K1T343 Series Face Recognition Terminal User Manual - Edit call No. for every button. - Check Call Management Center to set the button calling center. Note If you check Call Management Center and set the call No. as well, call management center has higher privilege than call No. 9.5.20 Access Control Settings Set Door Parameters Click Configuration → Access Control → Door Parameters . Figure 9-13 Door Parameters Settings Page Click Save to save the settings after the configuration. Door No.
DS-K1T343 Series Face Recognition Terminal User Manual Door Contact You can set the door contact as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Closed. Exit Button Type You can set the exit button as Remain Open or Remain Closed according to your actual needs. By default, it is Remain Open. Door Lock Powering Off Status You can set the door lock status when the door lock is powering off. By default, it is Remain Closed.
DS-K1T343 Series Face Recognition Terminal User Manual Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No.
DS-K1T343 Series Face Recognition Terminal User Manual 4. Click Save to save the settings. Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 9.5.21 Set Biometric Parameters Set Basic Parameters Click Configuration → Smart → Smart . Note The functions vary according to different models. Refers to the actual device for details. Click Save to save the settings after the configuration.
DS-K1T343 Series Face Recognition Terminal User Manual Continuous Face Recognition Interval Set the time interval between two continuous face recognitions when authenticating. Pitch Angle The maximum pitch angle when starting face authentication. Yaw Angle The maximum yaw angle when starting face authentication. Min. Detection Area (Width) Set the minimum width of the detection area. Min. Detection Area (Height) Set the minimum height of the detection area.
DS-K1T343 Series Face Recognition Terminal User Manual Set Recognition Area Click Configuration → Smart → Area Configuration . Drag the yellow frame in the live video to adjust the recognition area. Only the face within the area can be recognized by the system. Set Area Configuration, Margin (Left), Margin (Right), Margin (Top) and Margin (Bottom) as desired. Click Save to save the settings. Click or to record videos or capture pictures. 9.5.22 Set Notice Publication You can set the theme for the device.
DS-K1T343 Series Face Recognition Terminal User Manual Enable Sleep and the device will enter the sleep mode when no operation within the configured sleep time. Theme Management You can click + Add Program in the frame and upload the screen saver pictures from the local PC. Note By now, there is only one theme can be added. Play Schedule After you have created a theme, you can select the theme and draw a schedule on the time line to set the theme play schedule.
DS-K1T343 Series Face Recognition Terminal User Manual Chapter 10 Client Software Configuration 10.1 Configuration Flow of Client Software Follow the flow diagram below to configure on the client software. Figure 10-1 Flow Diagram of Configuration on Client Software 10.2 Device Management The client supports managing access control devices and video intercom devices.
DS-K1T343 Series Face Recognition Terminal User Manual 10.2.1 Add Device The client provides three device adding modes including by IP/domain, IP segment, and EHome protocol. The client also supports importing multiple devices in a batch when there are large amount of devices to be added. Add Device by IP Address or Domain Name If you know the IP address or domain name of the device to add, you can add devices to the client by specifying the IP address (or domain name), user name, password, etc. Steps 1.
DS-K1T343 Series Face Recognition Terminal User Manual Note ● This function should be supported by the device. ● If you have enabled Certificate Verification, you should click Open Certificate Directory to open the default folder, and copy the certificate file exported from the device to this default directory to strengthen the security. See for details about enabling certificate verification. ● You can log into the device to get the certificate file by web browser. 6.
DS-K1T343 Series Face Recognition Terminal User Manual Enter the device user name. By default, the user name is admin. Password Enter the device password. Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K1T343 Series Face Recognition Terminal User Manual characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 10.2.
DS-K1T343 Series Face Recognition Terminal User Manual 10.3.1 Add Group You can add group to organize the added device for convenient management. Steps 1. Enter the Device Management module. 2. Click Device Management → Group to enter the group management page. 3. Create a group. - Click Add Group and enter a group name as you want. - Click Create Group by Device Name and select an added device to create a new group by the name of the selected device.
DS-K1T343 Series Face Recognition Terminal User Manual 10.4.1 Add Organization You can add an organization and import person information to the organization for effective management of the persons. You can also add a surbodinate organization for the added one. Steps 1. Enter Person module. 2. Select a parent organization in the left column and click Add in the upper-left corner to add an organization. 3. Create a name for the added organization. Note Up to 10 levels of organizations can be added. 4.
DS-K1T343 Series Face Recognition Terminal User Manual 5. Click Download Template for Importing Person to download the template. 6. Enter the person information in the downloaded template. Note ● If the person has multiple cards, separate the card No. with semicolon. ● Items with asterisk are required. ● By default, the Hire Date is the current date. 7. Click to select the CSV/Excel file with person information from local PC. 8. Click Import to start importing. ● ● Note If a person No.
DS-K1T343 Series Face Recognition Terminal User Manual Export Person Information You can export the added persons' information to local PC as a CSV/Excel file. Before You Start Make sure you have added persons to an organization. Steps 1. Enter the Person module. 2. Optional: Select an organization in the list. Note All persons' information will be exported if you do not select any organization. 3. Click Export to open the Export panel. 4. Check Person Information as the content to export. 5.
DS-K1T343 Series Face Recognition Terminal User Manual Steps ● ● ● Note If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client. The gender of the persons will be Male by default. If the card number or person ID (employee ID) stored on the device already exists in the client database, the person with this card number or person ID will not be imported to the client. 1. Enter Person module. 2.
DS-K1T343 Series Face Recognition Terminal User Manual 10.4.5 Report Card Loss If the person lost his/her card, you can report the card loss so that the card's related access authorization will be inactive. Steps 1. Enter Person module. 2. Select the person you want to report card loss for and click Edit to open the Edit Person window. 3. In the Credential → Card panel, click on the added card to set this card as lost card.
DS-K1T343 Series Face Recognition Terminal User Manual Serial Port It is only available when the model is DS-K1F100-M. Select the COM the card enrollment station connects to. Buzzing Enable or disable the buzzing when the card number is read successfully. Card No. Type Select the type of the card number according to actual needs. M1 Card Encryption This field is only available when the model is DS-K1F100-D8, DS-K1F100-D8E, or DS-K1F180-D8E.
DS-K1T343 Series Face Recognition Terminal User Manual Note Up to 16 holiday periods can be added to one holiday. 1) Click Add in the Holiday List field. 2) Drag the cursor to draw the time duration, which means in that duration of time, the configured access group is activated. Note Up to 8 time durations can be set to one holiday period. 3) Optional: Perform the following operations to edit the time durations.
DS-K1T343 Series Face Recognition Terminal User Manual The access authorization is invalid in each day of the week and it has no holiday. 2. Click Add on the left panel to create a new template. 3. Create a name for the template. 4. Enter the descriptions or some notification of this template in the Remark box. 5. Edit the week schedule to apply it to the template. 1) Click Week Schedule tab on the lower panel. 2) Select a day of the week and draw time duration(s) on the timeline bar.
DS-K1T343 Series Face Recognition Terminal User Manual Steps When the access group settings are changed, you need to apply the access groups to the devices again to take effect. The access group changes include changes of template, access group settings, person's access group settings, and related person details (including card number, fingerprint, face picture, linkage between card number and fingerprint, linkage between card number and fingerprint, card password, card effective period, etc). 1.
DS-K1T343 Series Face Recognition Terminal User Manual Apply All to Devices This operation will clear all the existed access groups of the selected devices and then apply the new access group to the device. Apply Changes to Devices This operation will not clear the existed access groups of the selected devices and only apply the changed part of the selected access group(s) to the device(s). 4) View the applying status in the Status column or click Applying Status to view all the applied access group(s).
DS-K1T343 Series Face Recognition Terminal User Manual ● ● ● Note For the card related functions(the type of access control card), only the card(s) with access group applied will be listed when adding cards. The advanced functions should be supported by the device. Hover the cursor on the Advanced Function, and then Click to customize the advanced function(s) to be displayed. 10.7.
DS-K1T343 Series Face Recognition Terminal User Manual Normal Mode Recognize face via the camera normally. Deep Mode The device can recognize a much wider people range than the normal mode. This mode is applicable to a more complicated environment. Enable NFC Card If enable the function, the device can recognize the NFC card. You can present NFC card on the device. Enable M1 Card If enable the function, the device can recognize the M1 card. You can present M1 card on the device.
DS-K1T343 Series Face Recognition Terminal User Manual Name Edit the card reader name as desired. Door Contact You can set the door sensor as remaining closed or remaining open. Usually, it is remaining closed. Exit Button Type You can set the exit button as remaining closed or remaining open. Usually, it is remaining open. Door Locked Time After swiping the normal card and relay action, the timer for locking the door starts working.
DS-K1T343 Series Face Recognition Terminal User Manual Note The door or floor's status duration settings will be copied to the selected door/floor(s) as well. Configure Parameters for Card Reader After adding the access control device, you can configure its card reader parameters. Before You Start Add access control device to the client. Steps 1. Click Access Control → Advanced Function → Device Parameter . 2.
DS-K1T343 Series Face Recognition Terminal User Manual When the access control device cannot connect with the card reader for longer than the set time, the card reader will turn offline automatically. Buzzing Time Set the card reader buzzing time. The available time ranges from 0 to 5,999s. 0 represents continuous buzzing. Card Reader Type/Card Reader Description Get card reader type and description. They are read-only.
DS-K1T343 Series Face Recognition Terminal User Manual Max. Failed Attempts for Face Auth. Set the maximum live face detection failed attempts. The system will lock the user's face for 5 minutes if the live face detection is failed for more than the configured attempts. The same user cannot authenticate via the fake face within 5 minutes. Within the 5 minutes, the user can authenticate via the real face twice continuously to unlock.
DS-K1T343 Series Face Recognition Terminal User Manual Set Parameters for Face Recognition Terminal For face recognition terminal, you can set its parameters including face picture database, QR code authentication, etc. Steps Note This function should be supported by the device. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3. Select an access control device in the device list and click Face Recognition Terminal. 4. Set the parameters.
DS-K1T343 Series Face Recognition Terminal User Manual Set RS-485 Parameters You can set the access control device's RS-485 parameters including the baud rate, data bit, the stop bit, parity type, flow control type, communication mode, work mode, and connection mode. Steps Note The RS-485 Settings should be supported by the device. 1. Enter the Access Control module. 2. On the navigation bar on the left, enter Advanced Function → More Parameters . 3.
DS-K1T343 Series Face Recognition Terminal User Manual 7. Click Save. ● The configured parameters will be applied to the device automatically. ● After changing the communication direction, the device will reboot automatically. Enable M1 Card Encryption M1 card encryption can improve the security level of authentication. Steps Note The function should be supported by the access control device and the card reader. 1. Enter the Access Control module. 2.
DS-K1T343 Series Face Recognition Terminal User Manual Before You Start ● Add person and assign access authorization to designed person, and person will have the access authorization to the access points (doors). For details, refer to Person Management and Set Access Group to Assign Access Authorization to Persons . ● Make sure the operation user has the permission of the access points (doors). For details, refer to . Steps 1. Click Monitoring to enter the status monitoring page. 2.
DS-K1T343 Series Face Recognition Terminal User Manual Note The Capture button is available when the device supports capture function. The picture is saved in the PC running the client. For setting the saving path, refer to Set File Saving Path in the user manual of the client software. Result The icon of the doors will change in real-time according to the operation if the operation is succeeded. 10.8.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
DS-K1T343 Series Face Recognition Terminal User Manual Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression ● ● ● Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below. Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function. Do not make your hair cover your eyes, ears, etc.
DS-K1T343 Series Face Recognition Terminal User Manual 139
DS-K1T343 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix D.
DS-K1T343 Series Face Recognition Terminal User Manual Appendix E. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure E-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
UD24342B