Network PTZ Camera·Quick Start Guide Network PTZ Camera Quick Start Guide i
Network PTZ Camera·Quick Start Guide Quick Start Guide © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Network PTZ Camera·Quick Start Guide TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK.
Network PTZ Camera·Quick Start Guide PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
Network PTZ Camera·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Network PTZ Camera·Quick Start Guide 2015/35/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, please see: www.recyclethis.info.
Network PTZ Camera·Quick Start Guide Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Network PTZ Camera·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network PTZ Camera·Quick Start Guide Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. Make sure that the plug is firmly connected to the power socket. Make sure that the power has been disconnected before you wire, install or dismantle the PTZ camera. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
Network PTZ Camera·Quick Start Guide Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, replace the lens cap to protect the sensor from dirt. Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise (which is not a malfunction), and affect the endurance of sensor at the same time.
Network PTZ Camera·Quick Start Guide Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion. Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.
Network PTZ Camera·Quick Start Guide Table of Contents 1 Overview ....................................................................................1 1.1 Introduction ................................................................................... 1 1.2 Cable Descriptions ......................................................................... 1 1.3 Alarm Output ................................................................................. 2 2 Installation .........................................
Network PTZ Camera·Quick Start Guide 2.6.3 Base Mounting ..................................................................... 39 2.7 Installing DE4AxxxI Series PTZ Camera ....................................... 40 2.7.1 Ceiling Mounting .................................................................. 41 2.7.2 In-ceiling Mounting .............................................................. 41 2.8 Installing DE3AxxxI Series PTZ Camera ....................................... 44 2.8.1 Wall Mounting........
Network PTZ Camera·Quick Start Guide 1 Overview 1.1 Introduction The network PTZ camera has the following series: DE1Axxx(I) Series PTZ Camera DE2Axxx(I) Series PTZ Camera DE2xxx(I) Series Mini PTZ Camera DE3xxx Series PTZ Camera DY3xxx Series PTZ Bullet Camera DE4AxxxI Series PTZ Camera DE3AxxxI Series PTZ Camera Integrated with an optical zoom lens, this series of cameras feature in the PTZ limits, 3D positioning, Day/Night auto switch, 3D DNR, etc.
Network PTZ Camera·Quick Start Guide Power Cord DC12V IN Video Cable RS-485 Alarm Cable .. Audio Cable Network Cable Figure 1-1 Cables of PTZ Camera Power Cord: Supports 12 VDC power supply. Video Cable: Connect BNC Cable to test the video output. Alarm Cable: Connect terminal ALARM-IN with GND interface, and connect terminal ALARM-OUT with ALARM-COM interface. Audio Cable: Connect terminal AUDIO-IN with GND interface.
Network PTZ Camera·Quick Start Guide GND Output DC 30V 1A Power Supply JQC-3FG Relay (10A 250VAC) Direct load Relay Output OUT (n) OUT (n) + DC - ~220V AC Relay Output OUT (n) OUT (n) Figure 1-2 Alarm Output 3 FireWire Zero Line
Network PTZ Camera·Quick Start Guide 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Do not drag the PTZ camera with its waterproof cables; otherwise the waterproof performance is affected. Do not touch the bubble directly by hand. The image blurs otherwise. Do not power up the camera until the installation is finished.
Network PTZ Camera·Quick Start Guide Crack Cover 2.0 Figure 2-1 Open the Cover 2. Unscrew the screws on the camera base with the cross screwdriver, and remove the bubble, as shown in Figure 2-2. Bubble Screw Figure 2-2 Remove the Bubble 3. The position of memory card are various according to different camera model. Type I: open the memory card slot in the camera, and insert the memory card.
Network PTZ Camera·Quick Start Guide Reset Memory Card Slot Figure 2-3 Insert the Memory Card Type II: align the memory card with the memory card slot and insert it. Reset Memory Card Slot Figure 2-4 Insert the Memory Card 4. Align the bubble with the camera base, and install the bubble back. Fix the bubble with four screws, as shown in Figure 2-5.
Network PTZ Camera·Quick Start Guide Figure 2-5 Install the Bubble 5. Align the cover with the camera, and install the cover back, as shown in Figure 2-6.
Network PTZ Camera·Quick Start Guide 2.1.2 DE2Axxx(I) Series PTZ Camera Note: The installation steps are similar to the installation steps of DE1Axxx(I) series camera. Refer to section 2.1.1 DE1Axxx(I) Series PTZ Camera. 2.1.3 DE2xxx(I) Series Mini PTZ Camera Steps: Model Name: DS- 2DE2204I W- DE3/ W, DS- 2DE2402I W- DE3/ W 1. Open the memory card cover.
Network PTZ Camera·Quick Start Guide 2. Rotate the cover to a proper position, align the memory card with the memory card slot and insert it. Figure 2-9 Insert the Memory Card 3. Rotate the cover and push it back. 2.1.4 DE3xxx Series PTZ Camera Steps: 1. Loosen three screws on the bottom of camera to reveal the memory card slot, as shown in Figure 2-10.
Network PTZ Camera·Quick Start Guide 2. Align the memory card with the memory card slot and insert it. 3. Fix the screws and assemble the PTZ camera. 2.1.5 DY3xxx Series PTZ Bullet Camera For DY3xxx series PTZ bullet camera, the memory card slot is in the camera module and if you need, the memory card can be installed before the camera leaves the factory. In order to prevent damage, we highly recommend that you do not disassemble the PTZ bullet camera by yourself. 2.1.
Network PTZ Camera·Quick Start Guide Decorative Rim Bubble Flange Srews Figure 2-12 Remove the Bubble and the Decorative Rim 3. Open the memory card cover and insert the memory card into the card slot as shown in Figure 2-13 and Figure 2-14.
Network PTZ Camera·Quick Start Guide Memory Card Slot Memory Card Cover Figure 2-14 For 4× Camera Module 4. Close the memory card cover. Fix the four flange screws and push four silicone plugs back to assemble the PTZ camera. 2.1.7 DE3AxxxI Series PTZ Camera Steps: 1. Pull the decorative cover out and loosen 2 screws on memory card cover with screwdriver as shown in Figure 2-15.
Network PTZ Camera·Quick Start Guide 2. Remove the memory card cover, including sealing ring, and insert the memory card as printed mark. Memory card Figure 2-16 Insert the memory card 3. Screw the memory cover back, making sure the sealing ring is flat, and then close the decorative cover.
Network PTZ Camera·Quick Start Guide 2.2 Installing DE1Axxx(I) Series PTZ Camera 2.2.1 Ceiling Mounting Notes: The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories. Steps: 1. Rotate the installation plate anticlockwise, and remove the installation plate, as shown in Figure 2-18. OPEN Installation Plate Figure 2-18 Remove the Installation Plate 2.
Network PTZ Camera·Quick Start Guide Figure 2-19 Fix the Installation Plate 4. Route the cables from the cable hole in the installation plate. Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 5. Align the camera with the installation plate, and rotate the camera clockwise to fix it, as shown in Figure 2-20.
Network PTZ Camera·Quick Start Guide 2.2.2 Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps: 1.
Network PTZ Camera·Quick Start Guide Fixing Screw Bracket Base Figure 2-22 Remove the Bracket Base 3. Install the bracket base on the wall with four screws. Figure 2-23 Install the Bracket Base 4. Route the cables. Align the camera with the installation plate on the wall mounting bracket, and rotate the camera clockwise to fix it on the bracket.
Network PTZ Camera·Quick Start Guide 5. Connect the cables. Install the wall mounting bracket to the bracket base on the wall, and fix it with the supplied screw. Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. Figure 2-25 Fix the Bracket 6. Remove the protective film after installation. 2.3 Installing DE2Axxx(I) Series PTZ Camera Note: The installation steps are similar to the installation steps of DE1Axxx(I) series camera. Refer to section 2.
Network PTZ Camera·Quick Start Guide 2.4.1 Wall Mounting Notes: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its accessories. Steps: 1.
Network PTZ Camera·Quick Start Guide OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-27 Base Plate for DE2xxxI Series (IR) PTZ Camera 2. Align the cable hole on the base plate with the hole on the bracket for wiring. And install the base plate to the bracket by fixing three PM4×10 screws (supplied) to the holes marked with digit “2” on the bracket.
Network PTZ Camera·Quick Start Guide Figure 2-29 For DE2xxxI Series (IR) PTZ Camera 3. Route the cables through the cable hole. 4. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise to the base plate, and the PTZ camera is secured with the base plate by three locks on the plate.
Network PTZ Camera·Quick Start Guide OPEN LOCK Figure 2-31 Secure DE2xxxI Series (IR) PTZ Camera × 5. Secure the mounting base to the wall with four PA4 25 screws (supplied). Figure 2-32 Install the Mounting Base 6. Install the PTZ camera to the bracket. 1). Route the cables of the PTZ camera through the wall bracket. 2). Connect the corresponding cables. 3). Hang the bracket together with the PTZ camera on the mounting base. 4). Fix the mounting base with a PM4×10 screw.
Network PTZ Camera·Quick Start Guide Figure 2-33 Secure the Mounting Base Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 2.4.2 Ceiling Mounting Purpose: There are two ceiling mounting types provided for the camera, and we take the mounting without the junction box as the example. Notes: The ceiling mounting is applicable to the indoor/outdoor solid ceiling construction.
Network PTZ Camera·Quick Start Guide For the cables routed from the top of the back box, it is required to drill a cable hole in the ceiling. Figure 2-34 Cabling for DE2xxx Series PTZ Camera Figure 2-35 Cabling for DE2xxxI Series (IR) PTZ Camera Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. Ceiling Mounting without Junction Box Steps: 1.
Network PTZ Camera·Quick Start Guide Figure 2-36 Attach the Drill Template 3. Drill a cable hole in the ceiling according to the circle A on the template if you want to route the cables through the ceiling. Pull out the cable slot cover if you want to route the cables on the surface of the ceiling, as shown in Figure 2-37.
Network PTZ Camera·Quick Start Guide Cable Slot Cover Figure 2-38 For DE2xxxI Series (IR) PTZ Camera 4. Attach the base plate to the ceiling and secure it with the supplied three self-tapping screws by aligning with three screw holes in the ceiling, and the front arrows on the drill template and base plate should be aligned together as well, as shown in Figure 2-39 and Figure 2-40.
Network PTZ Camera·Quick Start Guide Figure 2-40 For DE2xxxI Series (IR) PTZ Camera 5. Route the cables through the cable hole. 6. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate.
Network PTZ Camera·Quick Start Guide 2.4.3 Installing with Junction Box Notes: The thickness of the ceiling shall range from 5 mm to 40 mm. Make sure the ceiling is strong enough to withstand more than four times the weight of the PTZ camera and its accessories. Steps: 1. Rotate the base plate counterclockwise to separate it from the PTZ camera. Notes: The base plate is not required when you install the PTZ camera with junction box. Keep it properly.
Network PTZ Camera·Quick Start Guide OPEN Base Plate on the Bottom of the Dome Front View of Base Plate Figure 2-43 For DE2xxxI Series (IR) PTZ Camera 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and make sure the front arrow appoints to the monitoring area. 3. Insert two PM4×10 screws into the ceiling, as shown in Figure 2-44. Figure 2-44 Attach the Drill Template 4.
Network PTZ Camera·Quick Start Guide on the drill template and junction box should be aligned together as well. Figure 2-45 Fix the Junction Box 5. Connect the cables and route the cables clockwise through the hooks and fix the camera and the junction box with three hooks. Tighten it clockwise and loosen it anticlockwise.
Network PTZ Camera·Quick Start Guide 6. Secure the PTZ camera and remove the protective film. 2.5 Installing DE3xxx Series PTZ Camera DE3xxx series PTZ camera supports ceiling mounting and in-ceiling mounting. Note: Wall mounting, installation with junction box, and installation with tripod are supported for DE3xxx series PTZ camera. The corresponding accessories shall be purchased separately. 2.5.1 Ceiling Mounting Notes: The thickness of the ceiling shall range from 5 mm to 40 mm.
Network PTZ Camera·Quick Start Guide Figure 2-47 Attach the Drill Template 3. Insert the expansion screws into the ceiling. (Optional) 4. Insert four PM4×10 screws into the ceiling and fix the base plate, as shown in Figure 2-48. Make sure the FRONT arrow of the base plate is of the same direction as the arrow of the drill template. Figure 2-48 Fix the Base Plate 5. Connect the cables and route the cable through the cable outlet. Align the PTZ camera with the base plate.
Network PTZ Camera·Quick Start Guide clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 6. Fix the screws on the side with a screwdriver, as shown in Figure 2-49. ③ ① OPEN ② LOCK Figure 2-49 Fix the Camera 7. Secure the PTZ camera and remove the protective film. 2.5.
Network PTZ Camera·Quick Start Guide 1. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and drill a hole in the ceiling according to the template. Figure 2-50 Drill Template 2. Fix the base plate onto the in-ceiling bracket with the four screws in the package (supplied). Make sure that the cable holes of the base plate are aligned to the cable holes of the bracket, as shown in Figure 2-51.
Network PTZ Camera·Quick Start Guide 3. Connect the cables and route the cable through the cable hole. Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 4. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 5. Fix the screws on the side with a screwdriver, as shown in Figure 2-52. ③ ① OPEN ② LOCK Figure 2-52 Fix the Camera 6.
Network PTZ Camera·Quick Start Guide Figure 2-53 Assemble the Decorative Rim 7. Secure the camera and remove the protective film. 2.6 Installing DY3xxx Series PTZ Bullet Camera 2.6.1 Dimensions of DY3xxx Series PTZ Bullet Camera Two structures of DY3xxx Series PTZ bullet cameras are available: wall-mounted PTZ bullet camera and base-mounted PTZ bullet camera. Select the proper PTZ bullet camera and the installation method according to its working environment.
Network PTZ Camera·Quick Start Guide 367 157 242 122 φ105 4-φ7 (74.2) Unit: mm (74.2) Figure 2-54 Wall-mounted PTZ Bullet Camera Dimensions of base mounted PTZ bullet camera is shown in Figure 2-55.
Network PTZ Camera·Quick Start Guide 2.6.2 Wall Mounting Before you start: The wall-mounted PTZ bullet camera can be installed on cement wall and pole mounting. The installing environment shall meet the following conditions: For cement wall, you need to use the expansion screw to fix the bracket. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the bracket. For wooden wall, you can just use the self-tapping screw to fix the bracket.
Network PTZ Camera·Quick Start Guide 3. Fix the camera on the wall by knocking the expansion screws into the wall through the bracket, as shown in Figure 2-57. Figure 2-57 Install the Wall-mounted PTZ Bullet Camera Notes: To install the PTZ bullet camera with the pole, you can use hexagon socket screws instead of the expansion screws. Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 2.6.
Network PTZ Camera·Quick Start Guide 1. Drill screw holes on the plane surface according to the dimensions of base-mounted camera. 2. Insert four M6 hexagon socket screws (with length of 30 mm) through the camera bracket and the plane structure, and then lock the screw nuts to fix the camera, as shown in Figure 2-58. Figure 2-58 Install Base-mounted Camera Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 2.
Network PTZ Camera·Quick Start Guide 2.7.1 Ceiling Mounting Ceiling mounting for DE4AxxxI series (IR) PTZ camera is similar to ceiling mounting for DE2xxx series & DE2xxxI series (IR) PTZ camera. Refer to section 2.4.2 Ceiling Mounting for details. Note: After DE4AxxxI series (IR) PTZ camera is installed, tighten the fixing screw with a screwdriver as shown in Figure 2-59. Fixing Screw Figure 2-59 Tighten the Fixing Screw 2.7.
Network PTZ Camera·Quick Start Guide Separate the Base Plate from the PTZ Camera Rotate Counterclockwise Figure 2-60 Separate the Base Plate from the PTZ camera 2. Attach the drill template (supplied) to the place where you want to fix the PTZ camera, and drill a hole in the ceiling according to the template. Ø 2 21 Figure 2-61 Drill Template 3.
Network PTZ Camera·Quick Start Guide Figure 2-62 Fix the Base Plate to In-ceiling Bracket 4. Connect the cables and route the cables through the cable hole. Note: Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 5. Align the PTZ camera with the base plate. Rotate the PTZ camera clockwise into the base plate, and the PTZ camera is secured with the base plate by three locks on the plate. 6.
Network PTZ Camera·Quick Start Guide 7. Place the camera and the bracket into the hole drilled in step 2, and rotate the screws clockwise to fix the camera. 8. Fix the decorative rim with the bubble and the decorative rim will be attached to the in-ceiling bracket automatically, as shown in Figure 2-64. ① Fix the Screw ② Fix the Decorative Rim Figure 2-64 Assemble the Decorative Rim 2.8 Installing DE3AxxxI Series PTZ Camera DE3AxxxI series PTZ camera only supports wall mounting. 2.8.
Network PTZ Camera·Quick Start Guide For wooden wall, you can just use the self-tapping screw to fix the bracket. Make sure that the wall is strong enough to withstand more than eight times the weight of the PTZ camera and its cable Steps: 1. Pull the bracket out from the side of the camera, and unclench the decorative cover as shown in Figure 2-65. Decorative cover Bracket Figure 2-65 Open the Decorative cover and pull out bracket 2.
Network PTZ Camera·Quick Start Guide and connect cables through the wall and the cable hole on the bracket. For the cables routed on the wall surface, you need to route the cables through the middle slot on the bottom of the back box, as shown in Figure 2-66. Cable slot Figure 2-66 Wiring on the wall 3. Fix the bracket to the target position with four screws (PA4×25) in the package (supplied), making sure the direction of the sign ”UP” is upward as shown in Figure 2-67.
Network PTZ Camera·Quick Start Guide Figure 2-67 Fix the bracket 4. Fix the camera to the mounting bracket. a. Route the cables. b. Align the camera to the wall mounting bracket, and push camera body until hear a click sound. c. Tighten the screws under the bracket. Figure 2-68 Fix the camera 5. Connect all the cables properly.
Network PTZ Camera·Quick Start Guide Water-proof treatment is required for cable connectors. Refer to section 2.9 and 2.10 for details. 6. Put cables in the back box, then close the decorative cover as shown in Figure 2-69. Back box Figure 2-69 Connect the cables 2.9 Installation of Network Cable Water-proof Jacket Purpose: If the camera is installed outdoor, you can assemble the water-proof accessory for the network cable to prevent the equipment from water.
Network PTZ Camera·Quick Start Guide ② ① ③ ④ ⑤ ⑥ Align ③ ④ ⑥ ① Figure 2-70 Installation of waterproof jacket Steps: 1. Feed the network cable through ① and ③ in order. 2. Fix ② on the network cable between ① and ③. 3. Place ⑤ onto the end of ⑥, and plug the RJ45 male connector into RJ45 female connector. 4. Screw ③ to ⑥ clockwise 5. Push ② into ③. 6. Secure ① with the ③ in clockwise direction. 2.
Network PTZ Camera·Quick Start Guide Steps: 1. Tear off the yellow release paper on the back of the water-proof tape. 2. Stretch the water-proof tape to reach twice the initial length. Initial Length Stretch Stretch Waterproof Tape Length After Stretching Figure 2-71 Stretch the Water-proof Tape 3. Wrap the water-proof tape around the cable connector tightly as the figure below.
Network PTZ Camera·Quick Start Guide Cable Connector Figure 2-72 Wrap the Water-proof Tape Note: Make sure that all naked wires are all firmly wrapped in the water-proof tape. 4. Press the tape on both ends of the connector to make sure no water can get in as the figure below.
Network PTZ Camera·Quick Start Guide 5. Wrap the water-proof tape around the remaining unused cables tightly as the figure below. Figure 2-74 Wrap the Unused Cables Note: Make sure that all naked wires are all firmly wrapped in the water-proof tape. 6. Press the tape to make sure no water can get in as the figure below.
Network PTZ Camera·Quick Start Guide 2.11 Protective Measures for Outdoor Installation If the device is installed outdoors, necessary protective measures should be taken to ensure safety. Scan the following QR code to get protective measures for outdoor installation.
Network PTZ Camera·Quick Start Guide 3 Activate and Access Network Camera Scan the QR code to get Activate and Visit Network Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
Network PTZ Camera·Quick Start Guide 55 UD11955B-B