Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition Related HIKOB products: GATEWAY H-GW103A GATEWAY H-GW103D-G INJ PH-AC100A INJ RH-AC100A ARM RH-AC100A ARM H-AC100A-ARM This document may not be reproduced (even partially) or communicated to 3rd parties without the written authorization of the company’s General Management. Copyright © HIKOB.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition Table of contents 1 Introduction........................................................................................................ 3 1.1 Symbols and conventions used in this guide ........................................................ 3 1.2 Safety instructions .................................................................................................... 3 1.3 Compliance and conformity ................................................
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition 1 Introduction When using GATEWAY, safety precautions must be taken to avoid injury and damages. Please read this guide before installing, using the product, or performing any maintenance operation. Failure to read, understand and follow herein instructions may result in personal injury. In no event shall HIKOB be held liable for any damages arising out of or related to misunderstanding instructions detailed in this manual. 1.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition 1.3 Compliance and conformity 1.3.1 Europe HIKOB SAS declares that the HIKOB GATEWAY LITE product is in accordance with stipulations of the RED 2014/53/UE, CEM 2014/30/UE and 2014/35/UE directives. 1.3.2 USA Information to user: This device complies with part 15 of the FCC Rules.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition 1.4 WEEE Information on disposal for users of waste electrical electronical equipment: This symbol on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be accepted free of charge.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition 2 General description 2.1 HIKOB Wireless sensor network acquisition system The GATEWAY is one of the elements that constitutes the HIKOB wireless sensor radio network. This system is a set of wireless sensors doing multi-point distributed measures in various domains. These sensors radio transmit their acquired data to the GATEWAY, possibly via LION routers, depending on environment constraints for radio transmission.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition ingress of dust, the second number 5, identifies protection against the effects of spraying water. Should you decide to perform cleaning tasks on the GATEWAY, don’t perform high pressure cleaning, prefer wiping with a dry cloth, or with a neutral agent.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition 3 Technical information 3.1 Global Power supply Power consumption Dimensions Type of fixing Weight Operating temperature Water index 3.2 Power over Ethernet with RJ45 connector following the 802.3at, 802.3af norm. (which corresponds for this product to 36 - 57 VDC, 0.1Amax). < 3W 22 x 12 x 3.8 cm Pole 360g Operating and Storage -20°C +60°C IP65 Radio 3.2.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition 4 Installation 4.1 Overall Methodology Installing an HIKOB radio network requires a good topology analysis of your site to maximize radio transmission quality by optimizing positions and numbers of HIKOB nodes in the network. A preliminary study done with your vendor determines elements that will constitute your HIKOB radio network acquisition.
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition • • 4.3 The PoE connector stamped IN goes to your IP network. You supply the PoE injector with cables and plugs following your country / area safety directives for electrical devices. Outdoor deployment The GATEWAY is suitable for outdoor use: the envelope has maximum protection against dust ingress and is water resistant (IP65).
Installation Guide INSTALL_GATEWAY-V5 2019/01 Edition Plug this set up connector to the female Ethernet connector on the back of the GATEWAY. 4.3.2 GATEWAY arm’s mounting process The GATEWAY is delivered ready to be installed. HIKOB highly recommends using RAM MOUNTS® products that can be optionally purchased with your GATEWAY, ask your vendor. This is a set of 3 elements: A first ball joint with a male screw that does the female thread on any 4 holes of the GATEWAY casing.