Handheld Thermography Camera User Manual .
© 2021 Hangzhou Microimage Software Co., Ltd. All rights reserved. About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the HIKMICRO website (www.hikmicrotech.com/).
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다. Safety Instruction The symbols that may be found in this document are defined as follows. Symbol Danger Caution Note Description Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
● If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. ● Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary. ● If the equipment is used in a manner not specified by the manufacturer, the protection provided by the device may be impaired.
CONTENTS 1 Introduction .................................................... 1 1.1 Product Introduction ................................. 1 1.2 Main Function ........................................... 1 2 Appearance ..................................................... 1 3 Preparation...................................................... 2 3.1 Charge Device............................................ 2 3.2 Power On/Off ........................................... 3 3.3 Interface Description ................
1 Introduction 1.1 Product Introduction The handheld thermography camera is a camera with thermal and optical images. The built-in high-sensitivity IR detector and high-performance sensor detects the temperature change and measure the real-time temperature. The accuracy of temperature measurement is ± 2 °C (3.6 °F) or ± 2% when the ambient temperature is from 15 °C to 35 °C (59 °F to 95 °F) and the object temperature is above 0 °C (32 °F).
Function Button Hold: Power On/Off Press: Display menu or confirm operation Exit the menu or return to previous menu. Navigation Button Press ▽, △ to select parameters. Press to confirm. Optical Lens Thermal Lens White Light Lens Protector Switch Trigger Hand Strap Hole Tripod Interface Component Function Charging Indicator When the device is charging, the LED indicator is solid red. When the device is fully charged, the LED indicator is solid green.
1. 2. Open the top cover of the camera. Connect the device interface and the power adaptor with Type-C cable. Type-C 3.2 Power On/Off Power On Remove the lens cover, and hold for over three seconds to turn on the device. You can observe the target when the interface of the device is stable. Power Off When the device is turned on, hold for three seconds to power off the device.
4.1 Set Thermography Parameters You can set thermography parameters to improve the accuracy of temperature measurement. Steps: 1 In the live view interface, press to show the menu. 2 Press / to select desired setting bar. 3 Press button to go to the setting interface. ⚫ Emissivity: Set the emissivity of your target as the effectiveness in emitting energy as thermal radiation. ⚫ Distance: Set the distance between the target and the device. ⚫ Unit: Set the temperature unit. Meas.
3 4 5 4.4 Go to Display, and select the hotspot, cold spot, center spot, or custom spot that you want to show on live view. Optional: You can customize the custom spot if needed. 1) Go to Custom Spot. Select the certain custom spot, and press . 2) Press / / / to adjust the position of the spot. 3) Press the trigger to finish setting. The device shows the real-time temperature on the upper left side of live view interface.
5 Capture Snapshots Steps: 1. In the live view interface, press show the menu. 2. to Press / , and select Picture Type. ● Offline Picture: Select this type when analyzing the picture with the HIKMICRO Analyzer. ● Thermal Graphic: Select this type for custom software development. 3. In the live view interface, pull the trigger to capture snapshot. The live view freezes and device displays the snapshot with temperature information. 4. Press press button to save the picture, button to cancel it.
● DO NOT disconnect the Type-C connection from PC or pull out the Micro SD card during drive installation or it may cause the device damage. 6 HIKMICRO Viewer Connection The device supports both Wi-Fi connection and WLAN hotspot. Connect the device to HIKMICRO Viewer App, and you can control the device via mobile App. 6.1 Connect via Wi-Fi Before You Start Download and install app on your phone. Steps: 1 In the live view interface, press to show the menu. 2 Press / , and select Wi-Fi.
You can view the live view, or capture snapshots via the app. 7 Image Settings Steps: 1. In the live view interface, press to show the menu. 2. Press / , and select Image. 3. Press , go to Image->Preview Mode, and select the preview mode needed. ⚫ Thermal: Display the thermal image only. ⚫ Fusion: Fuse the optical image with the thermal image. The fused image with clear edge is displayed in this mode. ⚫ Picture in Picture: Display a part of the thermal image on the optical image.
Steps: 1 In the live view interface, press to show the menu. 2 Press / , and enable Cast Screen. 3 Open HIKMICRO Analyzer and you can view the live view and operation of the device on HIKMICRO Analyzer. 10 Maintenance 10.1 View Device Information In the live view interface, press and select About to view the device information. 10.2 Set Date and Time In the live view interface, press and select Time & Date to set the information. 10.3 Format Memory Card Steps: 1.
After the upgrading, the device automatically reboot. You can view the current version in Menu > About. 10.5 Restore Device In the live view interface, press and select Restore to initialize the device and restore default settings. 11 Appendix 11.1 Common Material Emissivity Reference Material Emissivity Human Skin 0.98 PCB 0.91 Cement Concrete 0.95 Ceramics 0.92 Rubber 0.95 Paint 0.93 Wood 0.85 Asphalt 0.96 Brick 0.95 Sand 0.90 Soil 0.92 Cotton 0.98 Cardboard 0.
Q: The PC cannot identify the camera. A: Examine whether the device is connected to your PC with standard Type-C cable. Q: The camera can not be operated or no responding. A: Hold to reboot the camera.
Facebook: HIKMICRO Thermography LinkedIn: HIKMICRO Instagram: hikmicro_thermography YouTube: HIKMICRO E-mail: info@hikmicrotech.com Website: https://www.hikmicrotech.
