Handheld Thermal Camera HIKMICRO E Series User Manual Contact Us
Regulatory Compliance and Safety Information Read all information and instructions in this document carefully before using the device and keep it for further reference. For more device information and instructions, please visit our website at www.hikmicrotech.com. You can also refer to other documents (if any) accompanying the device or scan the QR code (if any) on the packaging to get more information. ©2023 Hangzhou Microimage Software Co., Ltd. All rights reserved.
PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. These clauses apply only to the products bearing the corresponding mark or information.
specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.
● The input voltage should meet the Limited Power Source (5 VDC, 2 A) according to the IEC61010-1 standard. Please refer to technical specifications for detailed information. ● Make sure the plug is properly connected to the power socket. ● DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire hazards caused by overload. ● Use the power adapter provided by a qualified manufacturer. Refer to the product specification for detailed power requirements.
radiation or dusty environments. ● DO NOT aim the lens at the sun or any other bright light. ● When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out. ● The device is suitable for indoor and outdoor uses, but do not expose it in wet conditions. ● The level of protection is IP 54. ● The pollution degree is 2.
CONTENTS 1 Introduction ..................................................... 1 1.1 Packing List ............................................... 1 1.2 Product Introduction ................................ 1 1.3 Main Function .......................................... 1 2 Appearance ...................................................... 2 2.1 Dimensions .............................................. 2 2.2 Components ............................................. 2 3 Preparation ...............................
1 Introduction 1.1 Packing List Handheld Thermal Camera (× 1) USB Cable (× 1) Wrist Strap (× 1) QSG (× 1) Calibration Certificate (× 1) 1.2 Product Introduction The handheld thermal camera is a camera with thermal and optical images. The built-in highsensitivity IR detector and high-performance sensor detects the temperature change and measures the real-time temperature.
Device supports superior to increase the image quality. Client Software Connection PC: You can download HIKMICRO Analyzer (https://www.hikmicrotech.com/en/industrialproducts/hikmicro-analyzer-software.html) to analyze pictures offline professionally, and generate a custom format report on your PC. You can cast the real-time live view of the device to your PC through the UVC alarm client. 2 Appearance 2.
2.2 Components Screen Charging Indicator Back Power/OK /Menu Button Navigation Function Hold: Power On/Off Press: Display menu or confirm operation Exit the menu or return to previous menu. In menu mode: Press and to select parameters. In live view mode: Press to switch image modes (only supported by certain models). Press to switch palettes.
Tripod Mount Wrist Strap Hole Component Function Charging Indicator Type-C Interface Solid Red: Charging. Solid Green: Fully charged. Charge the battery or export snapshots. In live view: Press: Capture snapshots. Hold: Locate the target with laser light, and release to capture snapshots. In menu mode, press the trigger to go back to live view. Trigger Tripod Mount Connect to UNC 1/4”-20 tripod. Note The appearance and button functions vary according to different models.
1 2 Lift the type-C interface cover. Connect the device to power supply using the type-C cable to charge the device. Type-C Interface Note The device is equipped with the built-in battery. For the first charge, charge the device for more than 3 hours when the device is turned on. 3.2 Power On/Off Power On Remove the lens cover, and hold for over six seconds to turn on the device. You can observe the target when the interface of the device is stable.
4 Display Settings 4.1 Set Image Mode You can set image modes of the device. Image Mode is only supported by certain models. Please refer to the actual device or the datasheet. Steps: 1 Select an image mode by the following ways: − Go to Settings → Image Settings → Image Mode, and select a preferred image mode. − Press modes. 2 3 in live view to switch image Thermal: Display the thermal image only. Fusion: Fuse the optical image with the thermal image.
Go to Settings → Palettes to select a preferred palette, and press to save and exit. Press in live view to switch palettes. 4.3 Set Level & Span Set a display temperature range and palette only works for targets within the temperature range. You can get better image contrast by adjusting the level & span parameters. Steps: 1 In the live view interface, press to show the menu. 2 Press / , and select Level & Span. 3 Select Setting Mode, and press to switch auto and manual adjustment.
5.1 Set Measurement Parameters You can set temperature measurement parameters to improve the accuracy of temperature measurement. Steps: 1 In the live view interface, press to show the menu. 2 Press / to select desired parameters. 3 Press to go to the setting interface. 4 Emissivity: Enable Custom, and select Emissivity to set the emissivity of the target as the effectiveness in emitting energy as thermal radiation by pressing / . Or you can select a preset emissivity.
Center: Display the center spot in the scene and show the center temperature. 4 Press to save and exit. Result: The device shows the real-time temperature on the upper left side of live view interface. 5.3 Enhance High-Temperature Target In target enhancement function, when the target’s temperature is higher than the set value, the target will become red. Steps: 1 You can enable target enhancement function by the following ways: − Go to Settings → Palettes, and select Above Alarm.
Steps: 1 In the live view interface, you can capture snapshots by the following ways. − Press the trigger in live view to capture snapshots. − Hold the trigger in live view to locate the target with laser light, and release the trigger to capture snapshots. Note ● Go to More Settings → Laser to turn on/off laser light. ● You cannot capture snapshots when the device is connected with PC.
3 Copy and paste the snapshots to PC and view the files. Disconnect the device from your PC. 4 Note ● For the first connection, the driver will be installed automatically. ● DO NOT disconnect the Type-C cable from PC during drive installation, or it may cause damage to the device. 7 Cast Screen The device supports casting screen to PC by UVC protocol-based client software or player.
Note Format storage before first use. 8.4 Upgrade Before You Start: Download the upgrade file from the official website first. Steps: 1 Connect the device to your PC with Type-C cable and open the detected disk. 2 Copy the upgrade file and replace it to the root directory of the device. 3 Disconnect the device from your PC. 4 Reboot the device and then it will upgrade automatically. The upgrading process will be displayed in the main interface. Note After the upgrading, the device automatically reboot.
9 Appendix 9.1 Common Material Emissivity Reference Material Emissivity Human Skin 0.98 PCB 0.91 Cement Concrete 0.95 Ceramics 0.92 Rubber 0.95 Paint 0.93 Wood 0.85 Asphalt 0.96 Brick 0.95 Sand 0.90 Soil 0.92 Cotton 0.98 Cardboard 0.90 White Paper 0.90 Water 0.96 9.2 Frequently Asked Questions (FAQ) Q: The charge indicator flashes red. A: Examine the items below. 1. Examine whether the device is charged with the standard power adapter. 2.
Facebook: HIKMICRO Thermography LinkedIn: HIKMICRO Instagram: hikmicro_thermography YouTube: HIKMICRO Thermography E-mail: support@hikmicrotech.com Website: www.hikmicrotech.
