Bodhi 10' x 10' Pergola Assembly Guide highwood NATURE'S CLOSEST RIVAL For information on Care and Cleaning or to register your highwood product, please visit www.highwood-usa.com. AD-PGLA-1010 12.20.
INCLUDED HARDWARE INCLUDED TOOLS x16 A 5/32" HEX BIT (Bolts A , B ) 1/4"-20 X 1.25" #2 SQUARE BIT (Screw E ) x96 B T15 TORX BIT (Screws C , "D") 1/4"-20 X 2.00" x16 C CUSTOMER-SUPPLIED HARDWARE #7 x 2.25" D E x56 ANCHORS SUITABLE FOR THE INSTALLATION SURFACE (MAX. 5 16 " x16 DIAMETER). #7 x 3.00" x16 #8 x 1.
PARTS LIST POST x4 LOWER SUPPORT BEAM x4 UPPER SUPPORT BEAM x4 JOIST x4 TOP SLAT x7 GUSSET ASSEMBLY x8 SLAT SPACER x2 JOIST INDEX x1 TOP SLAT INDEX x1 MAIN BEAM SPACER x1 highwood NATURE'S CLOSEST RIVAL For information on Care and Cleaning or to register your highwood product, please visit www.highwood-usa.com. AD-PGLA-1010 12.20.
PERGOLA ASSEMBLY Post (x2) "F" Metal Angle Bracket (2 per Post) 1) Set Two Posts on a Flat Surface Approximately 6 Feet Apart as Shown. 2) Align (1) "F" Metal Angle Bracket with the Corresponding Hole Pattern on the Side of Each Post. "A" Bolt (2 per Bracket) 3) Attach (2) "F" Metal Angle Brackets to the Bottom of Each Post using (2) "A" Bolts as Shown. Holes in the Brackets will Align with Holes in the Posts.
PERGOLA ASSEMBLY "B" Bolt (x8) 5) Place a Lower Support Beam Across the Top End of the Posts from Step 1, with the Brackets on the Lower Support Beam Facing UP. The Posts should be Oriented so the Holes in the Lower Support Beam Align with the Lower Set of (4) Holes in the Post. 6) Attach the Lower Support Beam to Each Post Using (4) "B" Bolts. Lower Support Beam highwood NATURE'S CLOSEST RIVAL For information on Care and Cleaning or to register your highwood product, please visit www.highwood-usa.
PERGOLA ASSEMBLY 7) Stand the Arch Assembly Up and Move to the Desired Location. If a Specific Orientation is Desired, Measure from Each Post to the Edge of an Adjacent Surface or Structure, Making Adjustments to Each Post as Needed to Achieve Equal Measurements. This Will Ensure the Pergola is Square with the Surface it Sits on, such as a Patio or Deck. Space the Bottoms of the Posts to Ensure the Spacing Shown Below.
PERGOLA ASSEMBLY "B" Bolt (x4) "B" Bolt (x4) DETAIL A B DETAIL B Upper Support Beam A 9) Lift an Upper Support Beam into Place as Shown. Support One End of the Beam Until Step 10, and Secure the Other End to the Arch Assembly from the Previous Step Using (4) B Bolts, as Shown in Detail A . 10) Place a Post at the Other End of the Upper Support Beam, Aligning the Support Beam with the Upper Set of Holes in the Post, and Secure Using (4) B Bolts as Shown in Detail B .
PERGOLA ASSEMBLY 11) Lift a Lower Support Beam into Place as Shown with Brackets Facing Outward. Support One End of the Beam Until Step 12, and Secure the Other End to the Post Using (4) B Bolts, as Shown in Detail A. A 12) Place a Post at the Other End of the Lower Support Beam, Aligning the Support Beam with the Lower Set of Holes in the Post, and Secure Using (4) B Bolts as Shown in Detail B . At this Point the Pergola Will Stand without Need for Additional Supports.
PERGOLA ASSEMBLY "B" Bolt (x4) DETAIL B B 13) Lift an Upper Support Beam into Place as Shown and Set on Top of the Lower Support Beams. Secure Both Ends to the Posts Using (8) B Bolts, as Shown in Details A and B . A Upper Support Beam "B" Bolt (x4) DETAIL A highwood NATURE'S CLOSEST RIVAL For information on Care and Cleaning or to register your highwood product, please visit www.highwood-usa.com. AD-PGLA-1010 12.20.
PERGOLA ASSEMBLY A 14) Attach the Remaining (2) Lower Support Beams Using (16) B Bolts, as Shown to the Right and in Detail A . These Should be Installed on the Opposite Sides of Each Post as the Lower Support Beams Installed Previously, with Metal Brackets Facing Inward. Quick Tip: Do not Fully Tighten Bolts Until all Bolts are Aligned and Started.
PERGOLA ASSEMBLY Upper Support Beam 15) Attach the Remaining (2) Upper Support Beams Using (16) B Bolts, as Shown to the Right and in Detail A . These Should be Installed on the Opposite Sides of Each Post as the Upper Support Beams Installed Previously. A Quick Tip: Do not Fully Tighten Bolts Until all Bolts are Aligned and Started. "B" Bolt (x4) DETAIL A highwood NATURE'S CLOSEST RIVAL For information on Care and Cleaning or to register your highwood product, please visit www.highwood-usa.com.
PERGOLA ASSEMBLY B Bolt (x4) 16) Place a Gusset Assembly Between the Lower Support Beams in Each of the (4) Locations Shown to the Right. The Threaded Inserts in the Gusset End Block Should Align with the Pre-Drilled Holes in the Lower Support Beams. 17) Secure Each Gusset Assembly to the Lower Support Beams Using (4) B Bolts, as Shown in Detail A . DETAIL A Gusset Assembly (x4) 18) Secure Each Gusset Assembly to the Adjacent Post using (2) C Screws as Shown in Detail B .
PERGOLA ASSEMBLY "B" Bolt (x4) DETAIL A 19) Place a Gusset Assembly Between the Upper Support Beams in Each of the (4) Locations Shown to the Right. The Threaded Inserts in the Gusset End Block Should Align with the Pre-Drilled Holes in the Upper Support Beams. Gusset Assembly (x4) 20) Secure Each Gusset Assembly to the Upper Support Beams Using (4) B Bolts, as Shown in Detail A . 21) Secure Each Gusset Assembly to the Adjacent Post Using (2) C Screws as Shown in Detail B .
PERGOLA ASSEMBLY 96 5/16" 22) Before Anchoring the Remaining Posts, Ensure the Pergola is Square by Adjusting the Two Unanchored Posts to Achieve the Post-to-Post and Diagonal Dimensions Shown to the Right. Measurements Should be Taken at the Bottom of the Posts. 124 3/16" 96 5/16" 96 5/16" 124 3/16" 23) Once the Pergola Frame is Square, the Remaining (2) Posts can be Anchored. Using Anchors Appropriate for the Anchoring Surface, Secure the Posts Using (2) Anchors in Each "F" Metal Angle Bracket.